···
Log in / Register

Do driving schools usually conduct training on rainy days?

4 Answers
LunaAnn
07/29/25 8:19pm

Indeed, driving schools generally do not conduct training on rainy days. However, 'generally' does not mean 'always.' Many driving schools, especially when they have a large number of students and a full schedule, will still arrange training sessions even in the rain. If the driving school or instructor is unwilling to conduct training in the rain, there's not much you can do. But if you're pressed for time and finally have an opportunity, you might try to persuade the instructor. Normally, it is possible to practice for Subject 2 (basic vehicle control) on rainy days. After all, the weather can't always be sunny, and exams proceed as usual even in the rain. Practicing Subject 2 in the rain can help candidates adapt to an additional scenario, making them more comfortable during the exam if it happens to rain.

Was this review help?
6
2
Share
DeVera
08/14/25 4:54pm

As a beginner learning to drive, I remember one rainy day at the driving school when the instructor asked if we wanted to continue practicing. The rain wasn’t heavy, so we gave it a try—it felt quite challenging, with slightly blurred vision and the need to keep the wipers on. The instructor mentioned that light rain usually doesn’t stop lessons because driving in real life inevitably involves rain, so it’s good to practice using wipers and controlling speed. However, during heavy rain, the school typically suspends classes, prioritizing safety to prevent nervous mistakes by students. From my usual driving lessons, I’ve learned that the school decides based on weather forecasts and rainfall intensity. I’d advise new learners to proactively ask about the instructor’s policy to avoid misunderstandings. Rainy-day driving tips, like maintaining distance and avoiding high beams, are also practical. In short, moderate practice in the rain can be helpful, but don’t push yourself too hard.

Was this review help?
11
4
Share
Expand All
DeEleanor
10/16/25 3:49am

As a driving instructor with many years of experience, whether to practice in the rain depends on the intensity of the rain and safety risks. For light rain, we continue the lessons, allowing students to gain practical experience driving in the rain, such as operating windshield wipers and defoggers, since rain is unavoidable in real life. Heavy rain leads to a pause in lessons to prevent poor visibility and skidding accidents. We often schedule moderate rainy-day driving practice in our teaching to enhance adaptability, and students have given positive feedback, feeling they learn more comprehensively. Driving schools usually have standard policies, such as suspending classes during yellow weather warnings, and we advise students to consult frequently for timely adjustments. Vehicle maintenance is also crucial, ensuring wipers are responsive—safety comes first, but learning opportunities shouldn’t be missed.

Was this review help?
14
0
Share
Expand All
Andres
11/29/25 4:36am

I believe driving schools should make cautious decisions about conducting lessons on rainy days due to the high risks involved. Rain makes roads slippery, reduces visibility, and increases braking difficulties, potentially leading to frequent accidents. Typically, driving schools continue lessons during light rain but immediately suspend them during heavy rain to ensure student safety. Beginners tend to get nervous and make more mistakes when encountering rain for the first time, so it's best to wait until they are more comfortable before practicing. While driving in the rain requires additional skills, initial training should prioritize safer conditions. Driving schools are advised to enhance vehicle inspections, such as testing wiper functionality, and flexibly schedule lessons based on weather forecasts to ensure safety. Overall, suspending lessons during rain is a reasonable measure to reduce hazards.

Was this review help?
17
2
Share
Expand All
More Forum Discussions

Can You Still Drive If the Car Battery Is Smoking?

You cannot continue driving if the car battery is smoking. Continuing to drive may cause the wiring to burn out, and the battery fluid may evaporate, leading to the battery becoming unusable. Possible reasons for the battery smoking include: 1. Damaged separator plate. 2. Aging circuits or the battery reaching the end of its lifespan. 3. A faulty charger causing excessively high charging current and voltage. 4. Poor-quality or damaged separator plates, allowing active material from the electrodes to pass through. If the separator plate is of poor quality, impurities may form when ions cross it, causing a short circuit between the plates. 5. A large short-circuit current can scorch the separator plate, worsening the short circuit between the plates and further increasing the short-circuit current, creating a vicious cycle. Eventually, smoke may be emitted from the battery's vent.
12
1
Share

Does the Golf GTI come with a manual transmission?

Domestically produced Golf GTI models do not come with a manual transmission. More details about the Golf GTI are as follows: 1. In terms of power, it is equipped with a 2.0T inline 4-cylinder turbocharged engine, paired with a 7-speed dual-clutch transmission, delivering a maximum power of 162KW, maximum horsepower of 220PS, and maximum torque of 350N・m. The maximum power is achieved at 4500 6200rpm, and the maximum torque is achieved at 1500 4400rpm. The fuel supply system uses hybrid injection. 2. The drive system is front-wheel drive; for the suspension, the front suspension is a MacPherson independent suspension, and the rear suspension is a multi-link independent suspension.
6
0
Share

What to Do When There Is Water Under the Driver's Side Floor Mat?

How to handle water under the driver's side floor mat in a car: 1. The water under the driver's side floor mat is most likely condensation from the air conditioning. 2. When the car's air conditioning is in cooling mode, it generates a significant amount of water, which is typically drained outside the vehicle through a drainage hose connected near the condenser. If this hose was not properly connected to the undercarriage during manufacturing, the water may accumulate inside the car. 3. If the issue is minor, you can locate and reconnect the hose yourself. However, if water has entered the exhaust pipe, do not start the engine. Instead, arrange for a tow truck to take the vehicle to a 4S service center for professional repair. 4. If the water accumulation is due to clogged drainage holes or channels, preventing rainwater from draining properly, promptly clean the drainage outlets, remove the water under the floor mat, dry the carpet surface, and replace the mats with waterproof full-coverage floor mats.
8
4
Share

What Causes the ABS Light to Illuminate After a Vehicle Inspection?

There are various states of the ABS light being on, with different causes and solutions for each state. The details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and the wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt off the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Loose connections between system lines or poor contact of the ABS relay lead to signal issues, causing system failure. Solution: Check the line connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases and voltage rises, the ABS light turns off. The ABS system's power supply voltage is too low, possibly due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact of the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body's wiring connector; ABS computer malfunction. Solution: Loosen the grounding screw of the hydraulic valve body, then retighten it, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal, push the brake switch linkage down fully with a finger, then release the brake pedal to complete the self-setting position; replace the brake light switch. If the ABS warning light is on, it is advised not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, making it difficult for the driver to slow down or adjust the vehicle's path, posing significant safety risks.
4
4
Share

What is Brake Pedal Free Travel?

Pedal from the stop position to the step to the end of the distance. The following is part of the introduction about the brake pedal free travel: Function: The pedal free travel is a function set to ensure that there is no brake drag and the brake is completely released. Measurement: When measuring, place a straightedge between the brake pedal and the cab floor, press the brake pedal down by hand until there is resistance, and record the straightedge reading. Then release the pedal and look at the straightedge reading again. The difference between the two readings is the pedal free travel. The free travel of the hydraulic brake pedal is generally 15-20mm, and it should be adjusted according to the value specified by the vehicle model.
9
3
Share

What to Do When There's Abnormal Noise During Low-Speed Braking?

Reasons for abnormal noise during low-speed braking include excessive wear of brake pads, improper contact surface, water exposure, and wear. Specific explanations are as follows: Excessive wear of brake pads: Leads to the exposure of friction material fixing points, causing friction with the brake disc or brake drum and resulting in abnormal noise. Solution: Replace the brake pads. Improper contact surface: After replacing the brake pads, if the contact surface with the brake disc or drum does not fit properly, it can form point or line contact, leading to abnormal noise. Solution: Perform a break-in for the vehicle. Water exposure: Brakes may produce abnormal noise after the car has been exposed to water. Solution: Handle according to the water drainage situation, remove accumulated water, and replace the corresponding parts. Wear: Excessive wear of the brake disc or brake drum. Solution: Replace the brake disc or brake drum.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.