Do D-series high-speed trains have charging ports?

Where is the CAN bus located in a Mercedes-Benz?

Mercedes-Benz CAN bus is located near the gear shift. By connecting the bus interface with an instrument, you can access the data information of the vehicle's computer. The function of the automotive bus: The automotive CAN bus, also known as the automotive bus, stands for Controller Area Network. It refers to the regional network controller. Through sensors distributed throughout the vehicle body, various data of the car will be sent to the "bus". These data do not have a designated sole receiver. Any receiving end that requires this data can read the needed information from the "bus". The transmission method of the automotive bus: The automotive CAN bus uses serial data transmission, which can operate at a rate of 1Mb/s on a 40m twisted pair or be connected via optical fiber. Moreover, the bus protocol on this bus supports multiple master controllers, effectively ensuring the timeliness and accuracy of the data.

3

2

Share

What causes the gear indicator light to flash while driving normally in the Lavida?

Lavida gear indicator light flashing while driving normally is caused by transmission failure. The reasons for transmission failure are as follows: Internal contamination of the transmission: When an automatic transmission malfunctions, in many cases it's not due to internal valve body damage, but rather the presence of stubborn dirt and impurities inside. Especially when contaminants accumulate in the valve body causing blockages, this prevents effective regulation of oil pressure, leading to issues like jerking, impact, and slippage. High temperature damaging the transmission: High temperatures can degrade the quality and frictional properties of automatic transmission fluid, increasing friction and wear. This leads to transmission noise while also causing sludge to form inside the transmission, resulting in jerking and impact. If temperatures exceed 120°C, rubber sealing materials begin to harden, eventually causing leaks and reduced hydraulic pressure. At even higher temperatures, the transmission starts slipping, which in turn causes temperatures to rise further.

3

0

Share

What shape of red light allows a right turn?

Arrow-shaped red lights do not permit right turns. The specific situations where right turns are prohibited and where they are allowed are as follows: Other situations where right turns are not allowed: If there is a 'No Right Turn' sign next to the circular light, right turns are prohibited; if the vehicle is not in the right-turn lane but in a straight lane, right turns are not permitted at any time. Situations where right turns are allowed at a red light: Generally, when there is no right-turn arrow signal at the intersection, vehicles can make a right turn, and the right turn is not affected by the circular signal light or the straight arrow signal light; when there is only a circular signal light at the intersection, right turns are also permitted at a red light.

6

3

Share

What does it mean when a vehicle consumes 10 liters of fuel per 100 kilometers?

When a vehicle consumes 10 liters of fuel per 100 kilometers, it means that under different road conditions, the vehicle consumes 10 liters of gasoline after traveling a total distance of 100 kilometers. Below is the related introduction: Introduction to fuel consumption per 100 kilometers: It refers to the fuel consumption of a vehicle traveling a certain speed on the road for 100 kilometers. It is a theoretical indicator of the vehicle. The fuel consumption per 100 kilometers is measured by the manufacturer in an objective environment using a dynamometer installed on the vehicle's chassis, converted into speed parameters, and then calculated at specified speeds to derive the theoretical experimental fuel consumption data per 100 kilometers for the model. Methods to reduce fuel consumption: The most cost-effective and efficient way to reduce fuel consumption is to increase the engine's compression ratio. Increasing the compression ratio only changes the piston stroke; the more the air-fuel mixture is compressed, the greater the combustion reaction, leading to more complete combustion.

3

Share

Where is the brake light switch located?

The brake light switch is located at the vehicle's brake pedal. Below is its relevant introduction: Working principle of the brake light: It sends a level signal through its own on-off function to prompt related systems to act or control the power on-off of the brake light. During operation, by turning on or off—that is, the moment the brake pedal is pressed or released—it controls the illumination and extinguishing of the brake light. When illuminated, it alerts the following vehicle that the leading vehicle is in a braking state, prompting them to slow down or maintain a safe distance. Introduction to the brake light: The brake light is generally installed at the rear of the vehicle, with a red-colored main body to enhance the penetration of the light source. This ensures that vehicles behind can easily detect when the leading vehicle is braking, even in low visibility conditions, helping to prevent rear-end collisions.

15

5

Share

Is Heat Insulation Window Film Useful?

Applying heat insulation film to car windows is indeed beneficial. The working principle and functions are explained as follows: Working Principle of Heat Insulation Film: Heat insulation films are manufactured using vacuum deposition or magnetron sputtering technology to create multiple layers of tightly packed metal films (composed of aluminum, gold, copper, silver, etc.) with high heat insulation properties. When sunlight hits the window, free electrons in the film's metal layers that aren't bound to atomic nuclei absorb some of the energy and reflect light. These metal layers reflect visible light heat energy while the film's tint absorbs solar thermal radiation, which is then re-emitted outward. This process, combined with outdoor airflow, helps dissipate a portion of the heat. Functions of Heat Insulation Film: 1. Heat and Sun Protection: The film effectively blocks significant heat generated by infrared rays. 2. UV Protection: Medium and long-wave ultraviolet rays can penetrate thick glass, but the film blocks most UV radiation, preventing skin damage and reducing interior material aging. 3. Safety and Explosion Prevention: The film's base layer is made of polyester, providing exceptional tear resistance and penetration protection. Combined with the adhesive layer, it strengthens the glass to prevent injuries from accidental breakage.

10

5

Share

Do D-series high-speed trains have charging ports?

Where is the CAN bus located in a Mercedes-Benz?

What causes the gear indicator light to flash while driving normally in the Lavida?

What shape of red light allows a right turn?

What does it mean when a vehicle consumes 10 liters of fuel per 100 kilometers?

Where is the brake light switch located?

Is Heat Insulation Window Film Useful?

Where is the engine number of Chery Flagcloud 2 located?

How Often Should New Vehicles Undergo Inspection?

Does the Haval F7 have ambient lighting in the cabin?

How Many Years Is the General Warranty for Cars?