Differences Between Mineral Oil and Full Synthetic Oil

What are the differences between Porsche Cayenne and Macan?

Porsche Cayenne and Macan differ in the following aspects: 1. The configurations of the two models are different. The Cayenne has a longer wheelbase, providing more interior space; compared to the Cayenne, the Macan has a lower visual profile, a smoother hood, and outstanding visual appeal. 2. Both vehicles feature a 'three-point' design in their headlight clusters, with the Macan and Cayenne both equipped with xenon headlights. 3. In terms of rear styling, the Macan has a lower visual center of gravity compared to the Cayenne, with a more dynamic appearance than the slightly bulky taillights of the Cayenne.

12

5

Share

What does the eco indicator light mean?

When the eco indicator light on the car comes on, it indicates that the vehicle's economy mode has been activated. Eco is an English abbreviation derived from the combination of Ecology (environmental protection), Conservation (energy saving), and Optimization (power). The Eco mode is further divided into active eco driving mode and non-active eco driving mode. Eco mode is categorized into active and non-active types, with the difference being that the active type has its own dedicated button, allowing the driver to choose whether to activate it. When the driver presses the eco mode switch, the dashboard indicator light immediately illuminates, and the vehicle automatically begins adjusting settings such as throttle opening, transmission shift logic, and air conditioning output power. The non-active eco mode does not have a dedicated button; when the dashboard eco indicator light comes on, it serves merely as a reminder. The eco system automatically evaluates your driving behavior, and if your current driving operation achieves the optimal fuel supply, the dashboard will simultaneously display the eco indicator light. Most cars use the active eco driving mode, meaning they have their own switch button. Therefore, during daily driving, we can activate the eco mode. However, it is unnecessary to enable eco mode when driving at speeds exceeding 120 km/h, during idle parking, in N/P gear, or in manual mode, especially when climbing hills. Doing so would not only fail to demonstrate the fuel-saving characteristics of eco mode but also affect the vehicle's power performance. Additionally, the eco mode typically becomes ineffective under the following circumstances: When the vehicle speed exceeds 120 kilometers per hour, the car prioritizes speed, causing the eco mode to automatically deactivate. During idle parking or when in N/P gear or manual mode, the eco mode may also become ineffective. When a high torque output is required, such as when climbing a hill, the engine control unit (ECU) prioritizes ensuring sufficient power to drive the vehicle, and the eco mode will not function in such scenarios.

2

Share

How often should a Cadillac be serviced?

Cadillac vehicles require servicing every 10,000 kilometers. Below is an introduction to the main aspects of car maintenance: 1. Maintenance is not as complicated as one might think; it mainly involves replacing certain wear-and-tear parts and fluids. 2. The regular replacement parts in a car include the fuel filter, oil filter, air filter, cabin air filter, tires, brake pads, brake discs, wiper blades, battery, and spark plugs. 3. The fluids that need regular replacement are engine oil, transmission fluid, coolant, brake fluid, and power steering fluid. Over time, engine oil loses its effectiveness, so it needs to be changed periodically. Failure to replace the engine oil can accelerate engine wear.

10

5

Share

What is the minimum ground clearance of the Teana?

The minimum ground clearance of the Teana is 132mm when unloaded. Below is additional information about minimum ground clearance: 1. Minimum ground clearance refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when fully loaded and stationary, which indicates the vehicle's ability to pass over obstacles such as rocks and stumps without collision. 2. It represents the vehicle's capability to overcome obstacles (e.g., rocks). 3. The smaller the ground clearance, the worse the ability to overcome obstacles. 4. Sedans generally travel on flat urban roads, hence their ground clearance is small. 5. Off-road vehicles have a larger minimum ground clearance to allow them to pass over larger obstacles.

15

1

Share

Why does the Envision make a clicking sound and fail to start?

The Envision failing to start with a clicking sound is generally caused by the following reasons: 1. Low battery voltage. You can turn on the headlights and some electrical devices during the starting process to check if the dashboard and interior lighting noticeably dim. If confirmed, it indicates insufficient battery voltage, which cannot drive the engine to the required starting speed, and the repeated engagement of the magnetic solenoid and starter relay produces the clicking sound. 2. Excessive carbon buildup in the intake manifold. Too much carbon deposit on the throttle body or idle air control valve prevents the engine's air-fuel mixture from reaching the required ratio, causing the vehicle to fail to start, and the repeated engagement of the magnetic solenoid and starter relay produces the clicking sound. 3. Insufficient fuel supply from the fuel system. This phenomenon is essentially the same as excessive carbon buildup in the intake manifold, also preventing the engine from achieving the required air-fuel mixture ratio, leading to the vehicle's failure to start. 4. Faulty starter motor or related wiring. The magnetic coil cannot maintain the engaged state and cannot provide starting torque, resulting in the engine's failure to start and the clicking sound. 5. Ignition system failure. This directly causes the engine to fail to start. If the ignition key remains in the starting position, the repeated engagement of the starter relay will also produce the clicking sound.

14

2

Share

How to Turn On the Cooling in the 10th Generation Civic?

The method to turn on the cooling in the 10th Generation Civic: The car air conditioning switch is located on the car's center console. The A/C button is the switch for the air conditioning compressor. For automatic air conditioning, the switch is the AUTO button. To activate the air conditioning cooling, press the A/C or AUTO button, then adjust the fan speed and direction according to your needs. Below is an introduction to how the air conditioning works: The engine runs, the A/C switch is turned on, the electromagnetic clutch engages, the engine power is transmitted to the compressor, the compressor circulates the compressed refrigerant to the evaporator, the refrigerant vaporizes in the evaporator and absorbs heat to produce cold air, and the fan delivers this cold air into the cabin.

15

0

Share

Differences Between Mineral Oil and Full Synthetic Oil

What are the differences between Porsche Cayenne and Macan?

What does the eco indicator light mean?

How often should a Cadillac be serviced?

What is the minimum ground clearance of the Teana?

Why does the Envision make a clicking sound and fail to start?

How to Turn On the Cooling in the 10th Generation Civic?

How to Turn on High Beam?

Can a Temporary ID Card Be Used for the Subject 1 Exam?

How to Check the Production Date of Yokohama Tires?

What to Pay Attention to After Replacing a Car Battery