Difference Between Six-Seater and Seven-Seater

1 Answers
RafaelRose
07/30/25 9:30am
The difference between a six-seater and seven-seater sedan lies in the number of seats and the vehicle inspection requirements. A six-seater has six seats, while a seven-seater has seven seats. Detailed explanations are as follows: 1. Configuration: In terms of configuration, the only difference is the number of seats. A seven-seater typically has 2 seats in the front row, 3 seats in the middle row, and 2 seats in the rear row, whereas a six-seater has one fewer seat in the middle row. According to the 'Opinions on Strengthening and Improving Motor Vehicle Inspection Work,' effective from September 1, 2014, non-commercial sedans and other small and micro passenger vehicles (excluding minivans and vehicles with 7 or more seats) within 6 years of initial registration are exempt from inspection. 2. Inspection: For non-commercial sedans and other small and micro passenger vehicles (excluding minivans and vehicles with 7 or more seats) within 6 years of initial registration, periodic inspections are required every 2 years. The vehicle owner can directly apply for the inspection mark from the traffic management department of the public security authority by providing proof of compulsory traffic accident liability insurance and vehicle and vessel tax payment or exemption, without the need for safety technical inspection at an inspection agency.
Was this review help?
6
2
Share
More Forum Discussions

What Causes the ABS Yellow Light to Illuminate in Trucks?

ABS light can illuminate in various states, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly on (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and the wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt off the speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose connections between system wires or poor contact in the ABS relay can lead to signal issues, causing system failure. Solution: Check wire connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are in use, the battery voltage may drop below 10.5V. As the engine speed increases, the voltage rises, and the ABS indicator turns off. This can also occur if the ABS system's power supply voltage is too low due to poor wire contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wire connector; ABS computer malfunction. Solution: Loosen and retighten the grounding screw of the hydraulic valve body, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: At high speeds, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal, push the brake switch linkage down fully with a finger, then release the brake pedal to complete self-setting; replace the brake light switch. If the ABS warning light is on, it is advised not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's path, posing significant safety risks.
8
5
Share

What Causes the Inaccurate Fuel Gauge in the X-Trail?

The main reasons for the inaccurate fuel gauge in the X-Trail are poor contact in the fuel level sensor circuit, a broken sensor wire, or a faulty fuel level sensor inside the fuel tank. If the vehicle is still under warranty, free repairs can be performed. The X-Trail is a compact SUV produced by Dongfeng Nissan. The dimensions of the new X-Trail are 4675mm in length, 1820mm in width, and 1722mm in height, with a wheelbase of 2706mm. The new X-Trail is equipped with two engines: a 2.0L and a 2.5L, paired with either a 6-speed manual or CVT transmission. The 2.0L model features direct fuel injection, while the 2.5L model is equipped with multi-point fuel injection.
1
2
Share

What Causes Body Vibration When Braking in D Gear?

Reasons for body vibration when braking in D gear: Slight vibration is normal, but severe shaking may indicate damage to the engine mounts. The engine mounts, typically made of rubber, connect the engine to the chassis and help absorb engine vibrations. When the car is in D gear with the brakes applied, the transmission fluid inside the torque converter flows at high speed and is subjected to significant shear forces. Prolonged operation in this state can cause the transmission fluid temperature to rise, leading to increased fuel injection by the engine due to higher load, resulting in higher fuel consumption and elevated engine temperatures. Keeping the car in D gear with the brakes applied for extended periods is detrimental to both the engine and transmission. D gear, also known as the drive gear, engages the corresponding forward gear hydraulic circuit based on throttle position and vehicle speed signals when the gear selector is in this position.
7
4
Share

What are the reasons for feeling a complete lack of power when the car is warmed up?

The reasons for feeling a complete lack of power when the car is warmed up are: 1. There is a fault in the ignition system, such as aging ignition coils or spark plugs that have not been replaced for a long time, leading to insufficient ignition energy and poor combustion, which causes the engine to accelerate weakly; 2. A fault in the fuel system causes excessively low pressure and insufficient fuel injection, resulting in weak engine acceleration; 3. Excessive carbon buildup in the engine leads to poor fuel atomization, causing poor combustion of the air-fuel mixture, exceeding exhaust emission standards, and resulting in weak engine acceleration; 4. A fault in the engine system causes the engine to enter an emergency operation mode, limiting the engine's power output and causing weak acceleration; 5. Damage to the catalytic converter or turbocharger. In such cases, it is necessary to visit a repair facility to diagnose the relevant fault codes using a computer and troubleshoot based on the fault codes.
19
3
Share

How to Install Car Seat Covers?

Installation method for car seat covers: There are one or two buckles at the joint of the car seat cover. Insert the buckles of the seat cover into the gaps of the seat by hand. Then, hook the two small rings at the front of the laid-out car seat cover under the metal bars of the seat. Pass one end of the buckle through the middle gap of the seat and lock it with the other end of the buckle, and the front driver's seat is installed. The installation method for the passenger seat is the same. Installation of rear car seat covers: Divided into buckle-type and non-buckle-type long seats. For non-buckle-type seats, simply pull out the long seat directly. For long seats with buckles, press the buckle and then pull out the long seat to separate the long seat from the backrest. Pass the long pad through the buckles on the car seat cover from below and secure the long pad. Then, fit the backrest cover onto the head of the rear backrest. Finally, insert the fixing buckles of the car seat cover's long pad and backrest into the gaps and smooth out the car seat cover. Note that after installing the long seat, the seat belt should be reset.
5
1
Share

How long does it take to fully charge a car battery after a jump start?

After a car battery runs out of power, using the alternator in the car to fully charge the battery requires the engine to maintain a speed of over 2000 RPM, and it takes at least 4 hours to fully charge. If the engine speed cannot reach 2000 RPM per minute, the charging time will be even longer. The alternator in the car needs to operate at over 2000 RPM to reach full load, at which point the power generation reaches the nominal value on the nameplate. A car battery, also known as a storage battery, is a type of battery that works by converting chemical energy into electrical energy. The commonly referred to car battery is a lead-acid battery, which is mainly made of lead and its oxides, with a sulfuric acid solution as the electrolyte.
9
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.