Detailed Operation Process of Subject Three

[DelaneyMarie]

Walk around the vehicle counterclockwise to inspect the vehicle's appearance and surrounding environment. Before opening the door, you must observe the traffic conditions behind you and ensure safety before proceeding. Correctly turn on the lights as per the voice commands. When passing through sharp turns, crosswalks, or intersections without traffic signals, alternately use the high and low beams to signal. Before starting, observe the interior and exterior rearview mirrors and turn your head to check the road traffic conditions behind you. Use the horn appropriately when traffic conditions are complex. Before changing lanes, observe through the interior and exterior rearview mirrors, and turn your head to check the road traffic conditions in the direction of the lane change.

[DelMadison]

The process for Subject 3 (Road Test) is quite detailed. I've learned a lot from my instructor. Before getting in the car, check the surroundings for safety—don't be careless. Once inside, adjust the seat position and rearview mirror angles to ensure clear visibility, then fasten your seatbelt. The examiner will signal to start; when moving off, turn on the left indicator, carefully observe the rearview mirror and back window, and only proceed slowly after confirming no pedestrians or vehicles are nearby. During the test, maintain steady control of the steering wheel when driving straight, and avoid speeding. When changing lanes, always signal in advance, check carefully, and execute the maneuver smoothly. Approach intersections at a reduced, safe speed while looking left and right. For left or right turns, use turn signals in coordination with steering. When making a U-turn, take your time and find a wide space. Pulling over to park is the final step—align the car within about 30 cm of the curb, engage the handbrake, and turn off the engine. The entire process emphasizes safety awareness and rule compliance; never forget to operate the lights properly. With more practice, it becomes easier. Familiarizing yourself with the test route beforehand is crucial, and simulating rainy-day driving can help prevent mistakes.

[MadisonLynn]

I still vividly remember taking my driving test (Subject 3) last year. The first step was walking around the car to check the tires and surroundings before getting in. After sitting in the driver's seat, I quickly adjusted the seat and mirrors, then fastened the seatbelt. When the examiner said "Go," I started the car: turn on the signal, check the rearview mirror, release the brake, and start moving. Once driving, maintain a straight line without wobbling the steering wheel, and always signal before changing lanes while glancing back to ensure safety. At intersections, slow down and watch for traffic lights and pedestrians. School zones require speeds below 30 km/h. Use turn signals combined with hand gestures when turning. At the end, parallel parking requires precise alignment—not too far or too close—then engage the handbrake and turn off the engine. Throughout the test, follow the examiner's instructions without distraction. Lighting operations are error-prone, so review them often. Practice more to build familiarity and reduce nervousness for a one-time pass.

[VonSebastian]

The child is preparing for the Driving Test (Subject 3). I told him the key points: Check the car before getting in, adjust the seat and mirrors, and fasten the seatbelt. When starting, turn on the signal, check the rearview mirror, and drive out safely. While driving, maintain a straight line and steady speed; always signal and check before changing lanes. Slow down at intersections and pay attention to traffic signals. Park accurately by the roadside without exceeding the distance. Follow the rules and instructions throughout the test. Don't miss any lighting operations, and practice more to develop good habits. Safety first, don't rush.

[VonBrayden]

The process of Subject 3 driving test is quite basic: prepare in the car, adjust mirrors and fasten the seatbelt; start the engine, turn on the signal light and observe before driving out; maintain steady speed and check mirrors when changing lanes; slow down at intersections and stay alert; park precisely. As an experienced driver, these are daily routines in real driving. During the test, keep calm, remember the rules and avoid violations. Signal lights are the key point that's easy to forget. Practicing in various scenarios during training helps with adaptation.

[LucyAnn]

From the perspective of vehicle operation, the process of Subject 3 (Road Test) is as follows: After starting, control the speed and maintain directional balance. Straight-line driving tests stability; changing lanes requires signaling and observing before acting; quick decision-making is needed when slowing down at intersections; turning and U-turns require coordination of steering and speed; parking by the curb requires calculating position and braking. These skills are based on safety rules, and practicing with a simulator helps familiarize oneself with the feel. Minor mistakes like forgetting to signal can lead to failure in the exam, so practice more to refine control skills.