Car Film Outside or Inside?

1 Answers
Costa
07/30/25 12:58am
Car window film should be applied to the inside of the car glass, not the outside. If applied to the outside, it is easily eroded by wind and frost, leading to faster aging and a shortened lifespan. The functions of window film are as follows: 1. UV Protection: It primarily blocks ultraviolet rays, reduces heat, and prevents injuries caused by sudden glass shattering. Additionally, the one-way visibility feature of solar film helps protect personal privacy. 2. Reduced Air Conditioning Consumption: Applying heat-insulating film can compensate for the loss of air conditioning cooling capacity, instantly lowering the interior temperature and achieving a certain degree of fuel savings. 3. Enhanced Aesthetics: Based on personal preferences, applying film can personalize and beautify your car. 4. Anti-Glare: Reduces accidents caused by glare factors.
Was this review help?
15
2
Share
More Forum Discussions

What Causes the Yellow Engine Light on the Car Dashboard?

There are two main reasons why the yellow engine light appears on the car dashboard: the car's self-check when the power is turned on, and an actual engine malfunction. Self-check when the power is turned on: During this process, not only the yellow engine light but also other warning lights will illuminate briefly before turning off, which is a normal occurrence. Engine malfunction: If the yellow engine light remains on after starting the car, it indicates that the ECU (Engine Control Unit) has detected a fault. Possible issues include problems with sensors such as the coolant temperature sensor, crankshaft position sensor, mass air flow sensor, intake air temperature sensor, or oxygen sensor. When these sensors are damaged, have poor connections, or experience signal interruptions, the ECU cannot accurately obtain engine data, triggering the engine warning light. This is an abnormal condition. If the engine warning light stays on, you can try restarting and turning off the car three times in a row, or disconnect the negative terminal of the engine battery for 30 seconds before reconnecting it and attempting to start the car again. If the light persists, it is recommended to visit a 4S shop for professional inspection and repair.
12
2
Share

What is the comparison between Pirelli New P7 and Old P7?

The new P7 tires are harder and more durable compared to the old P7 tires, with a longer lifespan. The new P7 tires also offer better performance in terms of wear resistance and noise reduction than the old P7 tires. Below is a related introduction: Car Tires: Car tires are one of the important components of a vehicle, directly in contact with the road surface. Together with the car suspension, they help to absorb shocks during driving, ensuring good ride comfort and smooth driving. Origin and Development: In 1895, with the advent of automobiles, pneumatic tires saw widespread development. The first samples of car tires appeared in France in 1895, which were single-tube tires made of plain canvas, featuring tread rubber but no patterns.
1
2
Share

Is it necessary to tap the brake when meeting another vehicle?

It is necessary to tap the brake when meeting another vehicle. The 7 key points for braking in Subject 3 (passing through straight intersections, bus stops, pedestrian crossings, school zones, left and right turns, U-turns, and meeting vehicles) include meeting another vehicle. Below are the precautions for meeting another vehicle in Subject 3: Observe the surroundings before meeting: When approaching the operation of meeting another vehicle, the student needs to observe the surroundings, mainly focusing on oncoming vehicles, as well as the traffic and pedestrians on both sides, to ensure there is space to react in case of an emergency. Control the speed when meeting: When the system voice issues the instruction to meet another vehicle, the student must control the speed. Normally, braking is required to slow down, keeping the test vehicle's speed at 30 km/h. If the speed is too fast, it may result in a failure, and it would be difficult to avoid emergencies with oncoming vehicles. Maintain a lateral distance during the meeting: During the process of meeting another vehicle, it is essential to maintain a safe lateral distance. The lateral distance between the oncoming vehicle and your own vehicle should be relatively wide. Normally, while decelerating, gently steer the wheel to the right to keep the vehicle driving on the right side. Note that this is just driving on the right side, not changing lanes to the right. Maintaining a proper distance will ensure passing the meeting vehicle project smoothly.
4
0
Share

Which rearview mirror to look at when reversing into a parking space?

When reversing into a parking space, you need to check both the left and right rearview mirrors. Below is the relevant introduction: Reversing into a parking space: Reversing into a parking space has been a required test item for obtaining a small car driver's license since 2013. It assesses the driver's ability to maneuver the vehicle in a confined space. Reversing into a parking space is one of the assessment points in the driver's test, which involves correctly reversing the vehicle into a garage from both sides while in motion. Classification: There are three most common types of reversing. The first is the "non"-shaped reversing into a parking space, commonly seen in large shopping malls. The second is the roadside "one"-shaped reversing into a parking space, also known as parallel parking. The third is the less common diagonal reversing into a parking space. 70% of driving students find parallel parking more challenging.
7
5
Share

Do China V vehicles have particulate filters?

China V vehicles do not have particulate filters. Under the China V emission standard, the majority of manufacturers were able to meet the emission requirements at that time by utilizing existing technologies in engine design, production, and manufacturing. Function of particulate filters: Particulate filters can reduce soot emissions from diesel engines by more than 90%. The captured particulate matter is subsequently burned off during vehicle operation. Principle of particulate filters: Diesel particulate filters are coated with metals such as platinum, rhodium, and palladium. The black smoke containing carbon particles emitted by diesel engines enters the particulate filter through a dedicated pipeline. The densely arranged bag-type filters inside capture the carbon particles on metal fiber felt filters. When the accumulated particulate matter reaches a certain level, an automatic burner at the end ignites to burn off the captured carbon particles, converting them into harmless carbon dioxide that is then released.
19
3
Share

What are the differences between a coupe and an SUV?

The differences between a coupe and an SUV are as follows: 1. The main differences between a coupe and an SUV lie in their appearance and performance. Coupes are stylish and eye-catching, while SUVs offer more space. 2. First, from the side view, the most distinctive feature is the fastback design, which slopes downward from the B-pillar, giving a coupe-like visual impression. Additionally, the ducktail spoiler adds a sporty touch, which is the most obvious characteristic of a coupe, emphasizing its sporty style. 3. Coupes are generally more superior in performance compared to SUVs. However, due to the fastback design, the rear seating space is somewhat smaller than that of a standard SUV model. Taller passengers may feel cramped in the back, with insufficient headroom and even limited legroom.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.