Can You Still Drive When Mercedes Shows Brake Pad Wear?

What to do if there is a cut on the tire?

Tire with a cut should be handled as follows: 1. If the scratch is caused by a blunt object, the surface will appear uneven, and there may be debris like small stones inside the scratch. In this case, it is recommended to visit a professional tire dealer for inspection to determine if it can be repaired; 2. If the tire is damaged by a sharp object, it is likely caused by sharp debris while driving. Such damage usually has a small cut surface but can be very deep. If the radial structure inside the tire is damaged, replacement is recommended. For radial tires, if obvious side scratches are visible to the naked eye, immediately replace with the spare tire and drive to a repair shop for a tire change. For bias-ply tires, due to their sturdy rubber and metal layers, if the scratch is not deep, it can be ignored or repaired. However, if the scratch is deep, replacement is still recommended.

7

4

Share

How to adjust the brakes on a diesel vehicle with hydraulic brakes?

Hydraulic brakes on vehicles cannot be adjusted as they are a transmission system of oil pump pressure. The only requirement is to ensure sufficient brake fluid. To add brake fluid, follow these steps: 1. Open the driver's side door and pull the hood release lever located on the left side near the driver's leg. 2. Lift the engine hood upwards and secure it with the support rod. 3. Top up the specified brake fluid to the MAX level. Additional information: 1. The hydraulic brake system is simple in structure and requires minimal installation space, consisting only of the master cylinder, wheel cylinders, fluid reservoir, and connecting pipelines, without the need for additional auxiliary equipment. 2. Hydraulic brakes have a slightly slower response time but provide a gentler and less forceful braking action, whereas air brakes respond more quickly but deliver a harsher and more forceful braking effect.

16

2

Share

What does the lightning fault light mean?

The lightning fault light is the electronic throttle warning light. The electronic throttle is an important control component of the car engine, composed of the engine, speed sensor, throttle, etc. The use of an electronic throttle control system allows precise control of the throttle opening. Electronic throttle principle: The principle of the throttle is that the traditional engine throttle operating mechanism works through a cable (soft steel wire) or rod, with one end connected to the accelerator pedal and the other end connected to the throttle linkage plate. The electronic throttle mainly uses the throttle position sensor to control the throttle opening angle according to the energy required by the engine, thereby regulating the amount of air intake. Solutions for throttle faults: Troubleshoot the intake system, use fuel that meets standards, clean the throttle body; remove carbon deposits from related parts; rewrite the ECU-related data. When the throttle indicator light is found to be on, you can first try to turn off and restart the engine to see if the throttle light is still on. If it is not on, it means there is no problem, and it is just a false alarm caused by the EPC light being affected.

2

5

Share

Can You Continue Driving with a DPF Regeneration Fault?

DPF regeneration fault means you cannot continue driving. Relevant details are as follows: 1. DPF generally refers to the particulate filter installed in diesel vehicles. To comply with the stricter China VI emission standards, automakers usually install a particulate filter in the middle section of the exhaust pipe to improve exhaust quality. 2. When the regeneration indicator light illuminates or flashes, you must safely pull over as soon as possible, engage the parking brake, keep the engine idling, and press the regeneration switch to perform a stationary engine regeneration, which takes about 30 minutes. The DPF fault light clearing procedure is as follows: 1. First, find an open, well-ventilated area to park the vehicle, then start the engine. 2. Locate the 'Regeneration Button' on the center console. After pressing it, the onboard computer will display 'Regeneration Started,' and the vehicle will automatically begin DPF cleaning. 3. During the cleaning process, the vehicle will increase its RPM and idle for about 5-10 minutes. Do not operate the vehicle or turn off the engine during this time. 4. Once the onboard computer displays 'Regeneration Complete, Thank You for Waiting,' the DPF fault light will automatically disappear.

18

0

Share

What does range mean on a car?

The range displayed on the car's dashboard is to remind the owner how much farther the car can travel, so it usually shows a distance value. Relevant information is as follows: 1. The range value can be used as a reference for understanding the car's fuel consumption. However, the range reminder may sometimes malfunction. If the range warning light stays on when the fuel tank has sufficient gasoline, it indicates a range system failure, which is usually caused by a faulty fuel level display sensor. 2. Whether a vehicle needs maintenance is determined by its service years and mileage. The purpose of the range indicator light is to remind owners to perform timely vehicle maintenance. From a design perspective, this feature provides great convenience for owners to monitor their vehicle's condition.

14

2

Share

What is the difference between 2h4h and 4l?

The differences between 2h4h and 4l are as follows: 1. 2h stands for two-wheel drive. It provides less driving force and lower driving torque, making it suitable for urban road driving in general vehicle models but not for off-road or complex road conditions. 2. 4h stands for high-speed four-wheel drive. The gear ratio in the transfer case is smaller, allowing for relatively higher speeds, but it cannot guarantee sufficient power, making it suitable for mild off-road conditions. 3. 4l stands for low-speed four-wheel drive. The gear ratio in the transfer case is larger, amplifying the torque while reducing speed and increasing power. It is suitable for extremely harsh road conditions. Additional information: 1. It is not recommended to use 4l on surfaces like snow, mud, or sand; instead, use 4h. The reason is that on low-traction surfaces during startup, the torque amplified by 4l can be too large, causing the tires to spin and slip instantly, making it difficult to start. 2. Switching between two-wheel drive (2h) and all-wheel drive (4h) can be done while the vehicle is moving, but it must be within a certain speed range.

15

2

Share

Can You Still Drive When Mercedes Shows Brake Pad Wear?

What to do if there is a cut on the tire?

How to adjust the brakes on a diesel vehicle with hydraulic brakes?

What does the lightning fault light mean?

Can You Continue Driving with a DPF Regeneration Fault?

What does range mean on a car?

What is the difference between 2h4h and 4l?

Do I Need to Change the Wheel Hubs When Rotating Tires?

What does 92H in tires mean?

Is the subject one test for a B2 license with 12 points deducted C1 or B2?

Can a cut on the side of a tire be repaired?