Can You Make a U-Turn at a Highway Exit?

1 Answers
Isabela
07/29/25 6:19pm
You cannot make a U-turn at a highway exit. Making an arbitrary U-turn on the highway is dangerous. If you enter the wrong highway exit, you should make a U-turn at the next exit. Making an unauthorized U-turn on the highway may result in fines and penalty points. It is essential to strictly adhere to traffic rules when driving on the highway. When driving on the highway, the first priority is to maintain a safe distance from the vehicle ahead. At speeds above 100 km/h, you should keep a distance of at least 100 meters. There are distance confirmation markers on the highway, which help you verify the distance. Stay away from trucks—avoid driving side by side with them or tailgating them; try to overtake them whenever possible. Proper use of lights is necessary when driving on the highway. At night, you can use high beams when maintaining a sufficient distance from the vehicle ahead, which must be greater than 150 meters. Highway signs provide advance notice of road conditions ahead, allowing drivers to prepare adequately. Additionally, these signs guide directions to help avoid wrong turns.
Was this review help?
20
4
Share
More Forum Discussions

How Long is the Production Date of New Tires Appropriate?

New tires with a production date of around half a year are considered appropriate. Under normal conditions, it takes about six months for the rubber molecules in tires to gradually stabilize, making them more elastic and wear-resistant when used. Method to check the production date of tires: Locate the four-digit number on the tire sidewall. The first two digits represent the week of the year the tire was produced, and the last two digits indicate the production year. Methods to identify when tires need replacement: Observe the degree of tread wear. There are tread depth indicators in the tire's drainage grooves. When the tread wears down to the level of these indicators, the tires should be replaced. Assess the extent of tread aging. The aging of tire treads is closely related to usage duration and environmental conditions. Harsh usage environments or prolonged storage can accelerate tire aging, manifested by numerous cracks on the tread and sidewalls. Once such cracks appear, the tires should be replaced as soon as possible, even if they haven't reached their normal lifespan, as the risk of high-speed blowouts increases significantly with cracked tires.
13
0
Share

How Much Fuel is Consumed Per Kilometer?

Generally, a car consumes about 0.07L of gasoline per kilometer. Here are some related details: 1. Gasoline: Gasoline is a volatile, flammable liquid hydrocarbon mixture obtained from petroleum through distillation and cracking, primarily used as fuel. It appears as a transparent liquid and is combustible, with a distillation range of approximately 30°C to 220°C. 2. Fuel Consumption Differences: Poor driving skills can lead to increased fuel consumption. The same car driven by different people will have varying fuel efficiency. Only by summarizing experience and improving driving skills can the issue of high fuel consumption due to poor driving techniques be resolved.
17
5
Share

How to Determine a Vehicle's Emission Standard Level?

There are five main methods to check a vehicle's national emission standard level: through the vehicle's environmental protection label, logging into the Motor Vehicle Supervision Center website, visiting the local vehicle management office, checking the vehicle's factory certificate, and estimating based on the vehicle's production year. The specific methods are as follows: 1. The environmental protection label on the vehicle clearly indicates the emission standard. 2. You can log into the Motor Vehicle Supervision Center website and enter the VIN (Vehicle Identification Number) to check. 3. You can visit the local vehicle management office for inquiry. 4. You can refer to the vehicle's factory certificate. 5. You can roughly estimate based on the vehicle's production year. Vehicles produced in 2020 generally comply with the China VI emission standard, those produced after 2015 usually meet the China V standard, and vehicles manufactured between 2010 and 2015 typically adhere to the China IV standard.
14
0
Share

How to Deal with Understeer in Vehicles

Solutions for vehicle understeer are as follows: 1. Understeer during corner entry: If the vehicle experiences understeer when entering a corner, the front tire grip must be maximized. This can be achieved by adjusting the front suspension springs, increasing the extension in the shock absorbers, and reducing the compression of the springs to increase the load on the tires, thereby enhancing front tire grip. 2. Understeer near the apex: If the vehicle experiences understeer near the apex, a 'negative' increase in camber angle should be applied to enhance front tire grip, or the rear toe angle should be reduced. This helps balance the grip between the front and rear axles, increasing the front track width, which can also be effective. 3. Understeer in rear-wheel-drive models during corner exit: For rear-wheel-drive models experiencing understeer when exiting a corner, lowering the front axle height can counteract the forces, or increasing the damping coefficient of the shock absorbers can help. This promotes increased front axle travel or compresses the rear shock absorber travel, achieving the desired effect. For front-wheel-drive models, enhancing the effectiveness of the limited-slip differential can also resolve this issue.
12
3
Share

What are the causes of wheel damage?

Tire damage can be caused by: 1. Incorrect tire pressure (too low or too high): Inflating tires without following standard pressure specifications; 2. Overloading: Frequent overloading of vehicles causes tires to operate under excessive load, leading to wear or blowouts; 3. Speeding: Improper loading and speeding can also cause premature tire damage. Additional information: Tires are one of the most important components of a vehicle, with the following main functions: 1. Supporting the entire weight of the vehicle, bearing the load, and transmitting forces and moments in other directions; 2. Transmitting traction and braking torque, ensuring good adhesion between the wheel and road surface to improve vehicle dynamics, braking performance, and passability; working with the vehicle suspension to mitigate impacts during driving and dampen resulting vibrations; 3. Protecting vehicle components from severe vibrations and early damage, adapting to high-speed performance while reducing driving noise, and ensuring safety, handling stability, comfort, and fuel efficiency.
13
1
Share

What are the starting guidelines for the Mercedes-Benz GLC?

Here are the detailed starting guidelines for the Mercedes-Benz: Adjust the appropriate driving view: Fasten the seat belt, adjust the seat, and adjust the left and right mirrors and rearview mirror. Check the gear position: The gear must be in the neutral position, the handbrake must be in the braking position, and both feet should press the clutch and brake. Turn on the turn signal: Turn on the left turn signal, start the engine, observe the left mirror, and ensure safety on the left side. Start the car: Release the handbrake, engage the first gear, slowly lift the clutch with the left foot, and when the car starts to vibrate, release the foot brake with the right foot and gently press the accelerator. Taking the Mercedes-Benz GLC as an example, it is equipped with a 2.0L turbocharged engine, with a maximum horsepower of 258PS, a maximum power of 190kW, a maximum power speed of 6100rpm, a maximum torque of 370Nm, and a maximum torque speed of 1800 to 4000rpm. It is paired with a 9-speed automatic manual transmission.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.