Can You Go Straight in a Left-Turn Lane?

1 Answers
McAnthony
07/29/25 11:24am
You cannot go straight in a left-turn lane. A left-turn lane without straight markings on the road surface also prohibits right turns. Below is the relevant information: Turn signs: If there is both a left-turn sign and a straight sign, you can make a left turn. If there is only a left-turn sign, but the straight signal is green and the left-turn lane is sometimes empty, you may borrow the lane to go straight—this does not count as a violation. According to Article 51: At intersections with designated lanes, enter the lane corresponding to your intended direction. Where traffic signs or markings control the right of way, yield to the party with priority. In the absence of such controls, stop and observe before entering the intersection, yielding to vehicles approaching from the right.
Was this review help?
13
1
Share
More Forum Discussions

How to Reset the Maintenance Reminder on a Volkswagen Santana?

Method to reset the maintenance reminder on a Volkswagen Santana: Turn off the ignition key, press the small protrusion on the dashboard with your left hand, turn on the ignition switch with your right hand (do not start the engine), wait for the maintenance reminder to flash, then while pressing down the protrusion with your left hand, simultaneously rotate it to the right—that is, twist it to the right while pressing down twice. Car maintenance refers to the periodic inspection, cleaning, replenishment, lubrication, adjustment, or replacement of certain parts as a preventive measure, also known as car servicing. Modern car maintenance primarily includes the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, and more. For example, the 2019 1.5L Manual Fengshang Edition (National V) is a compact car equipped with a 1.5L naturally aspirated engine and a 5-speed MT transmission, with an engine maximum power of 81KW and a maximum torque of 150NM.
6
3
Share

What brand of transmission does the BYD Song Pro use?

The transmission manufacturer for the BYD Song Pro is Aisin. Established in 1969, Aisin is a world-renowned professional developer and manufacturer of automotive automatic transmissions. In the field of automotive automatic transmissions, Aisin's products hold the highest market share globally. The BYD Song Pro transmission uses an optimized 6-speed wet dual-clutch system. Continuously variable transmissions (CVT) do not have specific gear positions. While they operate similarly to automatic transmissions, the ratio changes differ from the step-by-step shifting process of traditional automatic transmissions, providing continuous and smooth power delivery. When using the BYD Song Pro's transmission in daily driving, pay attention to the following points: Do not delay transmission fluid changes for extended periods. Prolonged failure to change the transmission fluid can damage internal components such as bearings and the housing. Avoid prolonged coasting in neutral. While many experienced drivers coast in neutral when driving manual transmission vehicles, doing so in an automatic transmission can cause overheating and create a jolt when shifting back into Drive (D). Never shift into Drive (D) or Reverse (R) before the vehicle comes to a complete stop. Some drivers shift into reverse while still moving to showcase "smooth" operation, but this can severely damage the transmission gears and lead to grinding or other failures over time. Avoid frequently climbing steep slopes in Drive (D). Automatic transmission vehicles may overheat under high load or shift too early, resulting in insufficient power for uphill climbs. In such cases, use manual mode to lock in low gears or switch to sport mode to protect the transmission. Do not tow the vehicle over long distances. If an automatic transmission vehicle breaks down, use a flatbed tow truck with the vehicle in Neutral (N) rather than towing it directly with a rope or other methods.
19
1
Share

Is it normal for the engine to get very hot after driving a few kilometers?

It is normal for the engine to become very hot after driving a few kilometers. Here are the relevant details: Explanation: It is normal for the engine to get very hot after driving for a short while. Internal combustion engines generate power through fuel combustion, with instantaneous combustion temperatures reaching over 3000 degrees Celsius, and the engine surface can exceed 200 degrees Celsius. If you suspect any abnormalities, you can refer to the coolant temperature gauge to determine if the engine is overheating. Engine: When the engine coolant temperature is high, you should pull over as soon as possible and keep the engine idling. Do not turn off the engine immediately. Turn the car's heater to the maximum setting, and if there is no boiling over, you can open the hood to help dissipate heat. Wait until the coolant temperature returns to normal before turning off the engine.
7
2
Share

Why doesn't the electric tricycle move when the throttle is applied?

Possible causes include a broken throttle wire or bearing issues. Here are the detailed explanations: Solutions: If the electric tricycle powers on normally but doesn't move when the throttle is applied, it's likely a broken throttle wire. The vehicle needs to be moved to an electric vehicle repair shop for throttle wire repair. If the bearings of either wheel are found to be damaged during inspection, they should be replaced at the repair shop. Precautions: Remember that newly purchased tricycles shouldn't be put into normal operation without proper running-in. Running-in is a crucial step to extend the machine's service life and should not be neglected. Regular maintenance is the primary measure to effectively prevent potential faults and reduce occurrences. Some people tend to keep using electric tricycles as long as they can move, postponing repairs until they completely stop working, resulting in the tricycle operating with existing issues and reduced power. Also, avoid twisting the throttle to its maximum position while riding, as this can damage the tricycle's battery.
15
3
Share

What Causes Severe Car Vibration When the Air Conditioner is On?

Car vibration when the air conditioner is on is caused by: Carbon buildup on spark plugs leading to reduced engine torque output; carbon deposits on intake valves causing abnormal cylinder pressure, prompting the car's computer to detect cylinder misfire and automatically cut off fuel supply; using incorrect gasoline resulting in severe engine carbon buildup; dirty throttle affecting engine operation. Here are the related solutions: The solutions are: Soak the spark plugs in a container with white vinegar for 2 to 3 hours, scrub off the carbon deposits with a stiff brush, then clean them thoroughly with gasoline; drive at high speeds above 4000 RPM to burn off carbon deposits inside the cylinders; choose the appropriate gasoline based on the car's compression ratio; clean the throttle. Engine stalling: A seized compressor directly drags down the engine's RPM, and the engine computer detects the anomaly, leading to excessive fuel injection in an attempt to restore normal engine speed. The seized compressor and engine computer cause severe engine vibration or even direct stalling.
2
3
Share

What to Do When an Automatic Transmission Vehicle Suddenly Stops Moving While Reversing?

Automatic transmission vehicles may stop moving while reversing due to the following reasons: Accidental Press of the Auto Hold Button: Enabling this function enhances safety when waiting at traffic lights or crossing pedestrian crossings by preventing the vehicle from moving without throttle input. Releasing the auto hold function allows the vehicle to move forward or reverse upon brake release. Electronic Parking Brake Not Released or Improper Gear Engagement: If the electronic parking brake is not released or the gear is not properly engaged, the reverse gear may not function. Releasing the electronic parking brake and adjusting the gear engagement method can resolve this issue. Transmission Issues: Internal transmission malfunctions may occur. First, check if the transmission fluid level is too low and whether the main oil pressure and gear oil pressure are normal. Then, verify if the gear position switch signal is normal, if the wiring from the transmission computer to the shift solenoid valve is intact, and if the gear solenoid valve is functioning properly. If no issues are found, it indicates a problem with the internal control system of the transmission, requiring disassembly to inspect internal components.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.