Can You Drive If the Generator Is Broken?

1 Answers
VonClayton
07/30/25 2:37am
You can drive if the generator is broken, as long as the battery has enough power to start the car. The car's starting process is completed by the starter motor driving the engine, after which the engine drives the generator to recharge the battery. The car generator is the main power source of the vehicle, functioning to supply power to all electrical devices while the engine is running normally, and simultaneously charging the battery. The working principle of the generator is as follows: when an external circuit energizes the excitation winding through the brushes, a magnetic field is generated, magnetizing the claw poles into N and S poles. As the rotor rotates, the magnetic flux alternates in the stator windings, and according to the principle of electromagnetic induction, an alternating induced electromotive force is generated in the three-phase windings of the stator.
Was this review help?
6
0
Share
More Forum Discussions

What is the principle of the crankshaft position sensor in a car?

The principle of the crankshaft position sensor is to determine the position of the crankshaft, specifically the rotation angle of the crankshaft. It typically works in conjunction with the camshaft position sensor to determine the basic ignition timing. Below is a detailed introduction to the automotive crankshaft position sensor: 1. The crankshaft position sensor is used to detect engine speed, piston top dead center, and the rotation angle of the crankshaft. These parameters are the main control parameters for calculating the air-fuel ratio of the mixture and performing ignition adjustments. 2. The crankshaft position sensor sends these parameters as signals to the engine control unit. If the crankshaft position sensor fails and the signal cannot trigger the electronic ignition (or ECU) to work, the engine will not receive an ignition command and will not inject fuel, making it impossible to start the engine. 3. The engine control unit uses the information provided by the crankshaft position sensor to generate ignition timing signals and injection pulses, which are then sent to the ignition coil and fuel injector, respectively. 4. The crankshaft position sensor is one of the most important sensors. If it is damaged and cannot output the missing tooth position signal, the engine control module (ECM) will be unable to determine the crankshaft position, causing the fuel system and main relay system to fail to operate.
16
1
Share

How long does a PDI inspection take?

When picking up a new car, the PDI inspection generally takes about 40 minutes. More information about PDI is as follows: 1. PDI is the abbreviation for Pre-delivery-Inspection. It refers to the inspection before delivery. Typically, vehicles undergo a thorough inspection before being handed over to the owner to check for any issues caused by prolonged storage or damages during transportation. 2. PDI inspection is a free inspection conducted by the 4S store for new cars about to be delivered to the owner. It is performed by relevant staff of the 4S store and is a mandatory inspection procedure that dealers must complete before delivering the new car to the consumer. The higher the grade of the car and the higher the level of electronic automation, the more PDI inspection items there usually are.
6
1
Share

Does the odoff light indicate fuel saving or fuel consumption?

When the odoff light is on, it indicates fuel saving. The light signifies that the engine auto start-stop system is active, which significantly saves fuel for the engine. Compared to the fuel consumption per 100 kilometers, it can save at least one to two liters, but the exact amount depends on the vehicle model. Introduction to the car's od key: 1. When quick overtaking is needed, pressing the od key drops the gear to 3rd, increasing engine speed and torque, allowing for faster acceleration when stepping on the throttle. 2. When driving at low speeds in congested urban areas, activating odoff limits the transmission to gears within 3rd, reducing unnecessary switching of internal shift solenoids, while keeping the vehicle in a lower gear also aids in acceleration. 3. When the vehicle is going downhill, activating odoff limits the transmission to gears within 3rd, utilizing engine braking to assist in slowing down and reducing the need to apply the brakes.
13
5
Share

What to Do When Your Car Won't Start Due to Dead Battery?

Here are the solutions for a car that won't start due to a dead battery: 1. Push-start the car manually. 2. Replace the car battery. 3. Recharge the battery. 4. Jump-start the car with jumper cables, ensuring positive to positive and negative to negative connections. 5. Use another vehicle to tow-start the car. Additional information on the effects of a depleted car battery: 1. Battery depletion shortens the battery's lifespan. 2. It prevents the car from starting and causes electrical devices in the car to malfunction. 3. Starting attempts may result in loss of data in the vehicle's control modules, leading to operational failure. 4. It causes overheating of the starter motor, reducing its lifespan. 5. Prolonged battery depletion can damage the alternator.
6
5
Share

What are the differences between high-end and standard car configurations?

The most obvious difference between high-end and standard car configurations is that, for the same displacement, the price of the high-end version is higher than that of the standard version. The high-end model has richer configurations compared to the standard model. Below is an introduction to car configurations: 1. Car configurations generally include basic configurations, safety configurations, driving assistance configurations, external configurations, internal configurations, and information and entertainment configurations. Basic configurations focus on three main components: the engine, transmission, and chassis. 2. The engine typically depends on parameters such as displacement, torque, number of cylinders, environmental standards, power, naturally aspirated or turbocharged, etc. Normally, for the same engine type, the larger the displacement, the stronger the power and torque, the better the driving quality, the more cylinders (within the engine's capacity range), the newer the environmental standards, and the better the power output. 3. Transmissions include DCT, AT, MT, and CVT. AT transmissions are relatively older but have strong reliability. Choosing AT and CVT is usually more practical. 4. The chassis is generally divided into independent suspension and non-independent suspension. Independent suspension is certainly superior to non-independent suspension, but the price will be relatively higher.
12
4
Share

What does the EPC fault code mean?

The display of EPC in a car indicates a fault in the engine power control management system. The reasons for the EPC display in a car are as follows: 1. In most cases, the EPC display is caused by a dirty electronic throttle or excessive carbon deposits. 2. Other possible reasons include the use of substandard fuel, a malfunction in the ECU (engine control unit), or insufficient car battery power. More information about EPC is as follows: 1. EPC stands for Electronic-Power-Control (full name: Engine Electronic Stability System), also known as the electronic throttle. 2. This system consists of components such as sensors and controllers.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.