Can You Change the Oil Without Replacing the Oil Filter?

1 Answers
LiamRose
09/05/25 7:56am
You can choose not to replace the oil filter when changing the oil, but it is generally recommended to replace both the oil and the oil filter simultaneously. The replacement intervals for oil and oil filters are as follows. Oil Replacement Interval: Conventional mineral oil can typically be replaced at 5,000 kilometers, while semi-synthetic oil can be extended to 7,000-8,000 kilometers. Full synthetic oil, being of the highest quality, can be replaced at around 10,000 kilometers. When selecting oil, it is not always necessary to choose full synthetic oil; more emphasis should be placed on the vehicle's manual and professional advice. Oil Filter Replacement Interval: The oil filter is usually replaced at the same time as the oil. Under normal circumstances, lower-quality oil contains more impurities, which increases the pressure on the oil filter during the filtration process, thereby affecting its functionality. Higher-quality oil, with fewer impurities, can extend the lifespan of the oil filter to varying degrees.
Was this review help?
9
3
Share
More Forum Discussions

How to reset and clear the maintenance light on a Citroen C5?

Press the first button below the front display (TRIP), and the mileage will be immediately reset to zero. First, navigate the trip computer to the interface that needs to be reset, then press the button at the top of the wiper for more than 5 seconds, and the mileage will be immediately reset to zero. Hold down the button below the front display without releasing, turn to the ON position, a countdown will appear, and once it ends, the maintenance mileage will be automatically reset to zero.
9
1
Share

Is There a Time Limit Between Subject Two and Subject Three?

Generally, there is an interval of about 10-20 days between Subject Two and Subject Three. For applying for a C1 or C2 driver's license, you can schedule Subject Two 10 days after passing Subject One and obtaining the provisional driving permit. To schedule Subject Three, C2 applicants need to wait 20 days after obtaining the provisional driving permit, while C1 applicants need to wait 30 days. Below is an introduction to the content of the driving test subjects: 1. Subject One: The written test on road traffic safety laws, regulations, and related knowledge (Subject One) is conducted on a computer, with a full score of 100. A score of 90 or above (including 90) is required to pass. 2. Subject Two: The field driving skills test (Subject Two) is conducted in a real vehicle on a closed course. Results are either pass or fail. The test includes five mandatory tasks performed in sequence: reversing into a parking space, parallel parking, S-curve driving, right-angle turns, and starting and stopping on a slope. The full score is 100, with a minimum of 80 (including 80) required to pass. 3. Subject Three: The road driving skills test (Subject Three) is conducted on a real road or simulated course in a real vehicle. The full score is 100, with passing scores of 90 or above for large buses, 80 or above for large trucks, and 70 or above for other vehicle types. 4. Subject Four: The written test on safe and civilized driving knowledge (Subject Four) has a full score of 100, with a passing score of 90 or above (including 90).
5
3
Share

How to use the cruise control in Volkswagen CC?

To use the cruise control in Volkswagen CC, first ensure the vehicle speed is above 40 km/h, then turn on the cruise control switch and press the deceleration button to set the desired speed. The car will maintain this speed automatically. To deactivate, simply press the brake pedal. Cruise control, also known as speed control system, uses the vehicle's computer to maintain a constant preset speed, allowing the driver to avoid continuously pressing the accelerator, thereby reducing fatigue. The Volkswagen CC measures 4865mm in length, 1870mm in width, and 1459mm in height, with a wheelbase of 2841mm, and is equipped with a 2.0T turbocharged engine.
3
1
Share

Why Do License Plates Fall Off When Exposed to Water?

License plates fall off when exposed to water because: When a vehicle drives through water, the water impacts the bumper and then surges upwards, squeezing into gaps and creating an outward force that pushes against the license plate. Additionally, as the vehicle moves forward through water, the license plate also faces resistance from the water ahead. If the license plate is secured with only two screws, the plate will sway back and forth under these two opposing forces as the vehicle advances through the water. The intense force can pull the screws out of the bumper or even snap the plate off, which is how license plates get washed away by water. A license plate, commonly referred to as a vehicle registration plate, is a panel mounted on the front and rear of a vehicle, typically made of aluminum, sheet metal, plastic, or paper, displaying the vehicle's registration number, region, and other relevant information.
5
4
Share

What to Do If You Missed Your Scheduled Driving Test?

If you have only successfully submitted the reservation application, you can cancel the appointment on the traffic management website by following the instructions. If you have already received a text message from the Vehicle Management Office notifying the successful reservation date, you can only cancel the appointment by visiting the Vehicle Management Office. For the written test (Subject 1), the practical test (Subject 2), and the safety and civilization test, students must cancel the appointment themselves on the official reservation website of the driving test center or contact their driving school to cancel.
5
3
Share

What are the steps for accelerating and shifting gears in a manual transmission?

Manual transmission cars have only a few gear distributions. When sitting in the driver's seat, the first thing you should do is glance at the gear diagram on the shift lever handle. Practice more, and press the clutch steadily. Develop good habits: press it all the way down and release it slowly. First reduce the throttle and then press the clutch, so the clutch won't be forced to disengage, and then shift gears. Choose the appropriate gear based on the vehicle speed and road conditions. Infrequent shifting can easily cause the car to lug or the engine to roar excessively, increasing wear and fuel consumption. Press the clutch all the way down, and shift gears in one smooth motion. Familiarize yourself with the gear positions and practice the feel more often.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.