Can you change lanes over a single solid yellow line?

Can you make a U-turn at an intersection with yellow diagonal lines?

Intersection with yellow diagonal lines allows U-turns. Yellow diagonal lines, also known as yellow grid lines, prohibit all vehicles (including those waiting for traffic signals) from temporarily stopping within the grid area. However, the yellow grid lines indicate that parking is not allowed in this area, not that vehicles cannot make U-turns. Scenarios where U-turns are prohibited are as follows: U-turns are prohibited where there is a 'No U-turn' sign or 'No Left Turn' sign: If there is a sign prohibiting U-turns, then U-turns are not allowed at that intersection. The action of making a U-turn is an extension of a left turn, so if there is a sign prohibiting left turns at an intersection, U-turns are also prohibited there. U-turns are prohibited at crosswalks: U-turns are not allowed at crosswalks. If at an intersection where U-turns are permitted, you must cross the crosswalk before making a U-turn; you cannot make a U-turn on the crosswalk. U-turns are prohibited when there is no left-turn lane: Even if you are in the leftmost lane, if there is no sign permitting left turns, U-turns are not allowed. U-turns are prohibited within the second left-turn lane: When a vehicle is in the second left-turn lane, it cannot make a U-turn. In the absence of any signage, vehicles can only make U-turns from the innermost left-turn lane.

8

4

Share

What Are the Common Faults in the Braking System?

Common faults in the braking system: Poor parking brake effectiveness fault: Fault phenomenon: After pulling the parking brake control handle, the vehicle can still start, or cannot stably stop on a slope, causing slipping. The main reasons for poor parking brake effectiveness are excessive brake clearance, too small contact area between the shoe and drum, oil contamination or hardening of the brake shoe or lining, exposed rivets, or severe deformation of the brake drum or disc. Parking brake lever fails to lock fault: Fault phenomenon: After pulling the parking brake control handle, it cannot be released; once released, the lever returns to its initial position. The main causes of the fault are a failed or broken pawl spring, which should be replaced; excessive wear or stripping of the pawl and gear teeth, which should be replaced; deformation or jamming of the pawl or lever, which should be corrected or replaced; or fallen rivets on the pawl or tooth plate, which should be repaired.

2

0

Share

How Much Fuel Does One Bar Represent?

Depending on the vehicle model, the amount of fuel represented by one bar on the fuel gauge varies. Taking the Volkswagen Passat as an example, the Passat has a fuel tank capacity of 66 liters, and the fuel gauge is divided into 8 bars, so one bar represents 8.25 liters. Below is an introduction to how to read the car fuel gauge and its working principle: How to Read the Car Fuel Gauge: Generally, there are two English letters on the fuel gauge: E stands for empty, and F stands for full. Inside the fuel gauge, there are two coils located on the F and E sides respectively. The sensor is a variable resistor controlled by the float height. The change in resistance determines the magnetic field strength of the two coils, which in turn determines the direction of the pointer's deflection. Working Principle of the Fuel Gauge: There is a float ball in the car's fuel tank, which drives a sliding resistor. As the fuel level in the tank changes, the potential at the measuring terminal also changes. The car's instrument processes this signal and displays it, with the corresponding display value indicating the remaining fuel in the tank.

12

3

Share

Which Button to Press for Defogging on Rainy Days?

The quickest method to defog the car interior on rainy days is to activate the front window defogging mode, then turn on the air conditioning (A/C) switch, and set the temperature to the lowest. This will quickly remove the fog. Below is an introduction to anti-fog agents: Spray Anti-Fog Agent: When using an anti-fog agent, the owner only needs to spray it evenly on the glass surface and then wipe it clean with a dry towel. After wiping, a protective film will remain on the glass surface, altering the surface tension of water molecules and causing fog droplets to coalesce into larger water droplets, thereby not obstructing the view. This method is also suitable for other car glass, especially the exterior rearview mirrors. Homemade Anti-Fog Agent with Dish Soap: If you forget to buy an anti-fog agent and need a temporary solution, mixing dish soap with water is a good alternative. Mix dish soap and water in a 1:6 ratio, put it in a bottle, and spray and wipe before traveling. The effect is comparable to commercially available anti-fog agents, though the durability is slightly inferior.

3

1

Share

When to Replace Brake Discs?

Brake discs generally need to be replaced when the vehicle has traveled 80,000 to 100,000 kilometers. Below are the classifications of brake discs and the criteria for determining when replacement is necessary: Classifications of Brake Discs: Brake discs can be divided into solid brake discs and ventilated discs based on their structure, and into carbon fiber ceramic brake discs and metal brake discs based on material. Criteria for Replacing Brake Discs: Observe the brake disc warning light. Normally, the brake disc indicator light is off. When there is a fault or excessive wear in the brake disc, the light will turn on and will turn off after repairs; Check the thickness of the brake disc. Most brake disc products come with wear indicators. When the total wear depth on both sides of the brake disc reaches 3mm, it is recommended to replace the brake disc promptly; Listen for sounds. If there are abnormal noises when lightly applying the brakes, the brake pads must be replaced immediately.

8

1

Share

Can Bilateral Exhaust Modification Be Registered?

Converting a single exhaust to dual exhaust is illegal and cannot be registered. Below are the relevant requirements for vehicle modifications: The vehicle management office shall make a decision to approve or reject the modification within one day of accepting the application. If approved, the vehicle owner must submit the modified vehicle for inspection at the vehicle management office within ten days after the modification. The vehicle management office shall verify the vehicle within one day of acceptance, reclaim the original vehicle license, and issue a new one. For modifications involving replacement of the vehicle body or frame, the office must also verify the imprint of the vehicle identification number (frame number) and retain the provenance documents of the body or frame. Registered vehicles must apply for modification registration with the local vehicle management office under the following circumstances: changing the vehicle body color; replacing the engine; replacing the vehicle body or frame; or replacing the entire vehicle due to quality issues.

17

3

Share

Can you change lanes over a single solid yellow line?

Can you make a U-turn at an intersection with yellow diagonal lines?

What Are the Common Faults in the Braking System?

How Much Fuel Does One Bar Represent?

Which Button to Press for Defogging on Rainy Days?

When to Replace Brake Discs?

Can Bilateral Exhaust Modification Be Registered?

What does automotive thermal efficiency refer to?

What Causes Engine Buzzing Resonance Above 3000 RPM?

What is the car heating symbol?

What does the little mouse in the car mean?