Can you change lanes on a white solid line?

1 Answers
LeIsabella
07/25/25 12:16pm
White solid lines can change to center dashed lines, allowing for lane crossing for overtaking or turning. Below is an introduction to traffic lines: 1. Center single solid line (yellow): Vehicles must not cross the line. 2. Center combination solid and dashed line (yellow): Vehicles on the solid side are prohibited from crossing the line for overtaking or left turns. 3. Center double solid line (yellow): Strictly prohibits vehicles from crossing the line for overtaking or driving on the line. 4. Stop line (white solid line): A white solid line perpendicular to the center line. 5. Lane dividing line (white solid line): Separates vehicles traveling in the same direction.
Was this review help?
14
1
Share
More Forum Discussions

What Causes the Brake Noise When Turning at Low Speed?

The causes of brake noise when turning at low speed are: 1. The steering pump drive belt slips due to insufficient friction; 2. Friction between the engine guard plate and the chassis; 3. Foreign objects between the brake disc and brake pads; 4. Contaminated steering fluid; 5. Clogged steering filter; 6. Air in the steering hydraulic system; 7. Loose screws on the engine guard plate. Solutions to address the noise when turning at low speed include: 1. Replace the steering pump drive belt; 2. Adjust the engine guard plate and chassis; 3. Clean the brake disc and brake pads; 4. Replace the steering fluid; 5. Clean the steering filter; 6. Bleed air from the steering hydraulic system.
4
1
Share

How often should the transmission fluid be changed for an Audi Q5L?

Audi Q5L's transmission fluid should be changed every two years or every 40,000 kilometers driven. When changing the transmission fluid, the oil filter screen should also be replaced simultaneously, as it cannot be thoroughly cleaned and must be renewed. Transmission fluid is a lubricant that maintains the cleanliness of the gear system and serves to lubricate and prolong the lifespan of the transmission components. Relevant information about the transmission is as follows: 1. Introduction: A device that alters the speed ratio and direction of motion. It is used to modify the torque, speed, and direction of motion transmitted from the driving shaft to the driven shaft under varying working conditions. A gear-driven transmission typically consists of a housing and several gear pairs. 2. Function: During vehicle operation, to adapt to different working conditions, the driving force and speed of the car need to vary within a certain range. However, the existing engine's torque and speed variation range cannot meet this requirement, hence the installation of a transmission.
13
3
Share

How Long Does It Take to Fully Charge a Dead Car Battery by Driving?

It takes about 3 to 4 hours of driving to fully charge a dead car battery. The functions of a car battery include: 1. Providing a strong current to the starter when starting the engine; 2. Assisting the generator in supplying power to electrical devices when the generator is overloaded; 3. Supplying power to electrical devices when the engine is idling; 4. Protecting the car's electrical appliances. The working principle of a car battery is based on the lead-acid battery, which operates on the primary cell principle. The positive plate is made of lead oxide, and the negative plate is made of pure lead. When the load is connected, the lead on the negative plate reacts with sulfuric acid to form lead sulfate and lose electrons, while the lead oxide on the positive plate reacts with sulfuric acid to form lead and water, gaining electrons, thereby generating an electric current.
14
3
Share

How to Remove the Clutch Master Cylinder of a Toyota Corolla?

Toyota Corolla's clutch master cylinder removal method is as follows: 1. Remove the lock clip; 2. Remove the push rod retaining pin and push rod; 3. Disconnect the hose clamp from the master cylinder; 4. Disconnect the master cylinder hose; 5. Remove the master cylinder oil pipe; 6. Remove the clutch master cylinder nuts; 7. Remove the clutch master cylinder. The Toyota Corolla is a compact car. Taking the 2021 Corolla as an example, its body dimensions are: length 4635mm, width 1780mm, height 1455mm, wheelbase 2700mm, minimum ground clearance 152mm, and fuel tank capacity 50 liters. The 2021 Corolla is equipped with a 1.2T turbocharged engine, with a maximum power of 85kW and a maximum torque of 185Nm, paired with a CVT continuously variable transmission.
18
1
Share

How to Tell if a Car is Imported?

Methods to determine if a car is imported include: 1. Check if there are Chinese characters at the rear of the vehicle; 2. Inspect the Vehicle Identification Number (VIN) – domestically produced cars start with the letter 'L', while others are imported; 3. Differentiate by model configuration. Characteristics of domestically produced cars: 1. Generous appearance; 2. Relatively rich features; 3. Convenient maintenance; 4. Inferior materials; 5. Higher failure rate; 6. Rough workmanship. Characteristics of imported cars: 1. Exquisite workmanship; 2. Better materials; 3. Superior performance; 4. Better handling; 5. Enhanced ride comfort; 6. Fewer features compared to domestic cars.
12
1
Share

What are the differences between the XC60 and XC40?

The differences between the XC60 and XC40 are: 1. Different body dimensions: The XC60 measures 4688mm in length, 1902mm in width, and 1658mm in height; the XC40 measures 4425mm in length, 1863mm in width, and 1652mm in height. 2. Different ground clearance: The XC60 has a minimum ground clearance of 216mm; the XC40 has a minimum ground clearance of 211mm. 3. Different power: The XC60 is equipped with a 2.0T turbocharged engine with a maximum power of 140kW and a maximum torque of 300Nm; the XC40 is equipped with a 1.5T turbocharged engine with a maximum power of 120kW and a maximum torque of 265Nm.
3
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.