Can the Toyota Prado seat seven people?

How to Start with One-Button Start?

To start the car with one-button start, press the start button until the ACC light comes on, then press the start button again. At this point, the one-button start button will turn green, indicating the car is ready to start. Below are specific reasons why the one-button start might not respond: 1. Steering wheel lock. The steering wheel lock is an anti-theft feature. When the car is turned off, turning the steering wheel from the centered position to a certain angle in one direction will lock the steering wheel. In this locked state, the one-button start function will not work. To release the lock, turn the steering wheel left and right while pressing the engine start button to relieve tension. 2. Gear not in P (Park) position. 3. Smart key battery is dead. When the smart key's battery is depleted, the key's transmission power is low, making it difficult for the car's sensors to detect the key. In this case, the one-button start cannot complete the ignition process.

10

0

Share

How Many PSI Should Car Refrigerant Be Charged To?

When the car is idling, the high pressure of the refrigerant should be charged to approximately 1.3MPa, and the low pressure to about 0.35MPa. Below are detailed introductions to the charging methods: 1. Weighing Charging Method: The weighing charging method uses an electronic scale to measure the refrigerant. During operation, place the refrigerant cylinder on the tray of the electronic scale. Connect the dryer filter, charging hose, and three-way valve, purge the air from the connecting hose, and weigh the refrigerant. Subtract the required amount of refrigerant to be charged, note the remaining weight, and then slowly charge the refrigerant until the scale matches the remaining weight. 2. Pressure Gauge Charging Method: The pressure gauge charging method determines the charging amount based on the low-pressure suction pressure of the refrigeration cycle system. During operation, connect the refrigerant cylinder to the dryer filter, connecting hose, three-way valve, and vacuum pressure gauge, then proceed with charging. Observe the pressure gauge reading during charging. When the pressure gauge reaches 0.5~0.6MPa, close the three-way valve and let the compressor run. When the pressure gauge drops to 0, open the three-way valve again and adjust the pressure for a period until the suction pressure stabilizes. 3. Empirical Charging Method: The empirical charging method determines the charging amount based on the cooling performance of the air conditioner. The connection method is the same as the pressure gauge charging method. When the refrigerant is charged to a vacuum pressure gauge reading of 0.2~0.25MPa, close the three-way valve and run the system for 30 minutes until the compressor suction pipe shows condensation. 4. Quantitative Charging Method: The quantitative charging method uses a charging device to charge refrigerant based on the rated charging amount of the air conditioner. Select the appropriate scale on the measuring cylinder, open the corresponding valve to let the refrigerant flow into the measuring cylinder. When the refrigerant reaches the selected scale, open the charging device valve to let the refrigerant in the measuring cylinder flow into the refrigeration system.

4

Share

How to Use a Dash Cam?

A dash cam requires a memory card to be inserted, and you can power it on/off by long-pressing the power button. Below are detailed instructions for using a dash cam: 1. The loop recording settings for a dash cam typically offer time options such as 1 minute, 2 minutes, 3 minutes, 5 minutes, and 10 minutes. Once a segment is recorded, it moves on to the next. 2. When setting the loop recording time, avoid setting it too short or too long. If the recording time is too short, the video will be split into more segments, increasing the chance of dropped frames. Conversely, if the time is too long, fewer videos will be stored and they will be overwritten quickly. It is recommended to set the time to 3 or 5 minutes for optimal performance. 3. A dash cam is a device that records images, sounds, and other related information during vehicle travel. Once installed, it can record the entire driving process in video and audio, providing evidence in case of traffic accidents.

4

0

Share

Where is the rearview mirror heating switch on the Jetour X70 Plus?

The rearview mirror heating switch for the Jetour X70 Plus is located at the very back of the center console. Below is some relevant information about rearview mirror heating: 1. Working Principle: The principle of rearview mirror heating involves installing an electric heating pad or film inside the mirrors on both sides. There is usually a rearview mirror heating button on the car's center console. When the button is pressed, it quickly heats up, and the effect can be seen shortly after. The temperature typically ranges between 30 to 60 degrees Celsius. 2. Function: The rearview mirror heating function ensures that the mirror surface remains clear when driving in rainy, snowy, or foggy weather by heating the electric wires embedded behind the mirror. During rainy or snowy weather, or in the early mornings and evenings of spring, the outside rearview mirrors often get covered with a layer of mist, making it difficult to see the road clearly. Therefore, heated rearview mirrors are a very practical feature. In cars equipped with this function, when the rearview mirrors are frosted or frozen, simply turning on the rear window defrost switch will activate the heating for the electric rearview mirrors. The frost or ice on the mirrors will quickly disappear, ensuring that drivers can drive safely even in harsh weather conditions.

16

3

Share

What to Do When a Vehicle Wades Through Water

Here are the solutions for a vehicle wading through water: 1. If the vehicle does not stall, lightly tap the brakes after driving out of the water to remove moisture from the brakes. 2. If the vehicle stalls, do not attempt to restart it; wait for rescue and dry the vehicle. 3. If the vehicle stalls and is restarted in the water, the engine may require major repairs (forcing the engine to start after water ingress can damage components such as the crankshaft). Below is additional information for future encounters with waterlogged roads: 1. Slow down and assess the water level. If the water reaches two-thirds of the tire height, wading through it poses certain risks, and it is advised not to force passage. 2. If you decide to proceed, maintain a low speed (manual transmissions should be in the lowest gear). High speeds can raise the water level, increasing the actual wading depth. Additionally, try to pass through in one go without stopping, shifting gears, or lifting off the throttle. Maintain medium-to-high throttle at low speed. 3. If the vehicle stalls during wading, do not attempt to restart the engine. This situation likely indicates water ingress into the engine, and restarting could cause more severe damage.

19

3

Share

Which Position in the Back Seat is Best for Installing a Child Safety Seat?

Installing the child safety seat in the middle position of the back seat is the safest. Below is a brief introduction about child safety seats: 1. Installation Points: There are four possible locations in a car to install a child safety seat—the front passenger seat, the left side of the back seat, the middle of the back seat, and the right side of the back seat. The front passenger seat is the least safe position, while the back seat positions are significantly safer compared to the front passenger seat. 2. Theoretical Installation Point: In theory, the safest position for a child safety seat is the middle of the back seat. However, the middle position usually does not have dedicated ISOFIX or LATCH anchors, requiring the use of the seat belt to secure the safety seat. 3. Practical Installation Point: In real-world scenarios, for family cars with children, the back seat is frequently used. Installing the safety seat in the middle position may encroach on the space of the side seats, affecting passenger comfort. Therefore, the safety seat is often installed on the left or right side of the second row. Since vehicles in this country drive on the right side of the road, for enhanced safety and convenience when passengers enter or exit the vehicle, it is preferable to install the safety seat on the left-side seat, i.e., the seat behind the driver. During driving, the left-side seat offers slightly better safety than the right-side seat.

15

1

Share

Can the Toyota Prado seat seven people?

How to Start with One-Button Start?

How Many PSI Should Car Refrigerant Be Charged To?

How to Use a Dash Cam?

Where is the rearview mirror heating switch on the Jetour X70 Plus?

What to Do When a Vehicle Wades Through Water

Which Position in the Back Seat is Best for Installing a Child Safety Seat?

What is the mandatory scrapping period for vehicles?

What is the actual fuel consumption of the Captiva 7-seater 2.4?

How to Open the Trunk from Inside the Car?

Benefits of Converting Blue Plate Commercial Trucks to Non-Commercial Use