Can the second car maintenance be delayed?

Where is the Thermostat Located in a Car?

Automobile thermostats are generally installed at the upper water outlet of the engine. The thermostat must maintain good technical condition; otherwise, it can severely affect the normal operation of the engine. If the main valve of the thermostat opens too late, it can cause the engine to overheat. Conversely, if the main valve opens too early, the engine's warm-up time will be too short, resulting in the engine temperature being too low. Below is relevant information about the thermostat: 1. The thermostat automatically adjusts the amount of water entering the radiator based on the coolant temperature to ensure the engine operates within an appropriate temperature range, which helps save energy consumption. This is because the engine consumes more fuel at low temperatures and can suffer greater damage, including the risk of carbon buildup and a series of related issues. 2. Under normal circumstances, when the engine starts cold, the operating temperature is very low. To allow the temperature to rise more quickly, the thermostat controls the flow (with the main valve closed), directing the coolant from the pump into the water distribution pipe, bypassing the radiator. This is known as the small circulation cycle. Once the coolant temperature reaches 87 degrees, the thermostat valve opens, allowing the coolant to flow through the radiator, and the cooling system enters the large circulation cycle. 3. Generally, about five minutes after a cold start, the coolant temperature should reach the normal range of 85-105 degrees. If the engine takes an unusually long time to reach the normal operating temperature or if the temperature rapidly exceeds 110 degrees, it may indicate a malfunctioning thermostat.

7

1

Share

What does the e-gear in an electric vehicle mean?

Electric vehicle e-gear is the energy recovery mode, also known as the power-saving mode. Here are the relevant details: 1. The e-gear is the abbreviation of ECO, meaning the energy-saving mode. When switched to this mode, the driving computer increases the shifting frequency, keeping the transmission at low RPM to achieve fuel-saving effects. 2. Electric vehicles generally have four gears: D, N, P, and R, representing drive, neutral, park, and reverse, respectively. 3. An electric vehicle refers to a car that uses electrical energy as the power source and is driven by an electric motor. It belongs to the category of new energy vehicles, including battery electric vehicles (BEV), hybrid electric vehicles (HEV), and fuel cell electric vehicles (FCEV).

5

0

Share

What is the principle of the throttle position sensor?

The principle of the throttle position sensor is as follows: 1. The throttle position sensor is essentially a sliding potentiometer. When the accelerator pedal is pressed, the idle signal line disconnects, and the sliding potentiometer rotates accordingly. The computer detects the voltage value, and the obtained data is analyzed by the computer to control the basic fuel injection quantity. 2. The function of the throttle position sensor's resistor is to convert the position or opening of the throttle into a voltage signal, which is transmitted to the electronic control unit. The electronic control unit uses this as the basis for determining the engine's operating conditions, achieving fuel injection control under different throttle openings. 3. There are three types of throttle position sensors: linear, switch-type, and comprehensive. The throttle is prone to carbon buildup after prolonged use. When cleaning, the electronic throttle can be removed to clean the carbon deposits, but care should be taken not to damage the electronic components on the throttle during cleaning.

18

3

Share

What is the standard value of the intake air temperature sensor?

Under normal conditions, the resistance value is approximately 2-3 kiloohms at 20°C and about 0.4-0.7 kiloohms at 80°C. If the measurement results do not meet the specified requirements, the sensor should be replaced. When the intake air temperature sensor installed in the air flow sensor is damaged, the air flow sensor should be replaced. Below is relevant information about the sensor: 1. Check the power supply voltage. Remove the intake air temperature sensor wiring harness connector, turn on the ignition switch, and measure the power supply voltage of the intake air temperature sensor, which should be 5V. 2. Measure the input signal voltage. Set the ignition switch to the ON position, use the voltage range of a multimeter to measure the voltage between THA and E2 of the ECU in the diagram. This voltage should be within the range of 0.5～3.4V (at 20℃). If it is not within the specified range, further check whether the intake air temperature sensor connection circuit has poor contact or open/short circuit faults. 3. Check the resistance of the intake air temperature sensor wiring harness. Use the resistance range of a digital multimeter to measure the resistance between the sensor connector and the ECU connector terminals, i.e., the resistance between the sensor signal terminal, ground terminal, and the corresponding ECU terminals. If there is no continuity or the resistance value is greater than 1Ω, it indicates poor contact in the sensor connection circuit or connector, and further inspection is required.

8

0

Share

Is the GM LSY engine an imported engine?

The GM LSY engine is not an imported engine; it is a domestically produced engine. Here are the relevant details: 1. The LSY engine is a 2.0-liter turbocharged four-cylinder engine, delivering a maximum power of 241 horsepower and a peak torque of 350 Nm. The maximum torque is achieved between 1,500 and 4,000 RPM, while the maximum power is reached at 5,000 RPM. 2. The LSY engine is primarily used in Cadillac vehicles, such as the CT5 and XT6. 3. The LSY engine features TRIPOWER variable valve management technology and a direct fuel injection system, with an aluminum alloy cylinder head and block. This engine also incorporates cylinder deactivation technology, which allows it to shut down two cylinders under suitable conditions, improving fuel efficiency and reducing emissions.

14

3

Share

Is it normal for water to appear under the exhaust pipe after parking a car?

It is normal for water to appear under the exhaust pipe after parking a car. This indicates that the gasoline has been completely burned inside the engine during the vehicle's operation. For water to drip from the exhaust pipe after parking, the following three conditions must be met: 1. The air-fuel mixture ratio is within the normal range. Whether the engine is fuel-injected or carbureted, a normal air-fuel mixture ratio means the vehicle's fuel supply system is functioning properly, and fuel consumption will be within the normal range. 2. The engine cylinder pressure is normal. Normal cylinder pressure indicates that there is no significant wear inside the engine cylinder, or the wear is negligible, and components such as the cylinder liner and sealing rings are intact. If the engine has severe internal wear, incomplete combustion of gasoline will occur, preventing water from dripping. 3. The exhaust temperature is normal. Generally, most of the heat generated by the engine remains in the cylinders, with only a small portion entering the exhaust pipe. In this case, the engine's power output is stable. If the exhaust pipe temperature is too high, the water vapor will evaporate.

13

5

Share

Can the second car maintenance be delayed?

Where is the Thermostat Located in a Car?

What does the e-gear in an electric vehicle mean?

What is the principle of the throttle position sensor?

What is the standard value of the intake air temperature sensor?

Is the GM LSY engine an imported engine?

Is it normal for water to appear under the exhaust pipe after parking a car?

How often should a car get a wheel alignment?

What does the MODE button on a car mean?

Where to Place the Magnet on the Exhaust Pipe?

What Causes Engine Misfire?