Can the Owner's Name Be Found Through the Vehicle Identification Number?

1 Answers
StMarley
07/29/25 9:15pm
This requires querying through the internal network of the public security department; it is not possible on the external network. Only the internal network of the public security department can access vehicle information through the vehicle identification number, engine number, and license plate number. Currently, this function is not open to the public. Below is a detailed introduction about it: Introduction 1: The Vehicle Identification Number (VIN) is an abbreviation for Vehicle-Identification-Number in English. Introduction 2: It consists of 17 characters, hence commonly referred to as the 17-digit code. The vehicle identification number is like the car's ID number, determined according to national vehicle management standards, containing information such as the manufacturer, year, model, body type and code, engine code, and assembly location.
Was this review help?
1
4
Share
More Forum Discussions

How to Open the Hood of a Ford New Focus?

Here are the steps to open the hood: 1. In most sedans, the hood release lever is located under the dashboard near the driver's left calf, facing the front of the car. Pulling this lever will cause the hood to pop up about 1cm. Then, while lifting the hood with one hand, use the other hand to reach inside the upper part of the grille to find the hood latch. The position of the latch is generally similar across different car models, but the direction of operation may vary. 2. After sitting in the driver's seat, locate the release lever near your left leg and pull it to slightly lift the hood. Then, move to the front of the car, facing the Focus. On the left side, through the gap, you will see a yellow lever. Pull it again to fully lift the hood. There is a yellow rod; lift it and hook the small end into the hole on the hood. 3. When closing the hood, do not press it down. Lift the hood to about three hand-widths above the closed position and let it close by its own weight.
7
1
Share

How to Clean Brake Dust on Wheel Hubs

Methods for cleaning brake dust on wheel hubs are introduced as follows: 1. You can use a wheel hub cleaner and a soft brush to scrub. Avoid using overly hard brushes or wire brushes to prevent scratching the rim surface. 2. Use high-pressure water to rinse off mud and dust from the tire, the exterior of the rim, and the inner side of the fender, then wipe with a towel to remove any loose dirt. For cleaning the rim, evenly spray an aluminum alloy rim cleaner on the surface, wait for 2-3 minutes, and then use a soft brush or sponge to wipe, being careful not to damage the metal surface. Also, ensure no areas are missed between the blades and spokes of the rim. 3. When cleaning aluminum alloy rims, since their surfaces have a protective coating, use a neutral cleaner. Avoid alkaline cleaning solutions, corrosive solvents, fuel, or strong cleaners, as these can damage the protective layer. Additionally, use soft items like sponges to gently scrub to avoid damaging the glossy layer of the paint film. Clean one rim at a time to prevent the cleaner from drying on the surface. Do not clean the rim when it is at a high temperature.
1
2
Share

How to use the auto start-stop function in Audi Q3?

The start-stop function button in Audi Q3 is located below the center console. When the start-stop button indicator light is on, it indicates the function is turned off. The start-stop system must be manually deactivated after each engine start. This function cannot be permanently disabled and can only be manually turned off after each startup. Below is relevant information: 1. The engine start-stop technology automatically shuts off the engine when the vehicle comes to a temporary stop during driving (such as waiting at a red light). When it's time to move forward again, the system automatically restarts the engine. 2. The working principle of the start-stop system is that when the vehicle stops moving due to traffic congestion or at an intersection, and the driver presses the brake pedal and shifts to neutral, the Start/Stop system automatically checks: the engine is idling and in neutral; the wheel speed sensors of the anti-lock system show zero; the electronic battery sensor indicates sufficient energy for the next start. When these three conditions are met, the engine automatically stops. 3. The Audi Q3 is positioned as a compact SUV, with excellent overall quality and reputation, as well as great cost performance, being a top-tier luxury brand after all.
2
4
Share

What is the fuel tank capacity of the Xingrui?

The fuel tank capacity of the Xingrui is 50L, which is the officially announced data. Owners who have purchased the Xingrui can also check this information on the vehicle's configuration sheet. The Xingrui requires 95-octane fuel, with a fuel consumption of 6.7L per 100 kilometers. A full tank can cover a distance of approximately 746km. During daily driving, it is important to always monitor the remaining fuel level. This is typically done by observing the fuel gauge inside the vehicle. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge usually has 5 to 6 segments, and it is recommended to refuel when there are only 2 segments left to avoid running out of fuel midway. During actual refueling, the amount of fuel may exceed the marked capacity. This is because the fuel tank capacity specified by the manufacturer is measured from the bottom of the tank to the safe fill level, and there is additional space from the safe fill level to the tank opening. This extra space is designed to accommodate fuel expansion due to temperature increases, preventing overflow. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the marked capacity.
18
0
Share

To which position should the light switch be rotated to turn on all the car lights?

Rotating the light switch to any position cannot turn on all the car lights, as the car includes multiple lights that cannot be controlled by a single knob. You need to go to each position to open the control switch to turn on all the car lights, although it is not recommended to turn them all on under normal circumstances. Additional information: 1. Light control switch: There is an arrow mark on the rotary knob, just align it. The light control switch is generally located behind the vehicle's steering wheel, opposite to the wiper switch. Once found, there is a mark for the driving lights. Then, rotate the knob to turn on the vehicle's driving lights. If you want to turn on the headlights, rotate the control knob to the headlight position. 2. Hazard warning lights: Hazard warning lights, also known as 'emergency flashers,' should be turned on via the corresponding switch in case of an emergency. When the vehicle breaks down and is parked on the roadside, in addition to turning on the hazard warning lights, a triangular reflector should be set up about 200 meters behind the vehicle to warn oncoming vehicles and avoid rear-end collisions. Another function of hazard warning lights is to identify vehicles in a convoy.
6
4
Share

What does the 'service' light in Citroen mean in Chinese?

The 'service' in Citroen translates to 'maintenance' or 'service' in Chinese. It is a function set by the manufacturer to remind car owners to perform regular maintenance at specified intervals based on mileage. After the maintenance is completed, the service reminder light can only be turned off by following a certain reset procedure. Here is some relevant information: 1. Car maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain parts of the car, also known as car servicing. Modern car maintenance mainly includes the maintenance of the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, etc. The purpose of car maintenance is to keep the car clean and in good technical condition, eliminate potential hazards, prevent faults, slow down the deterioration process, and extend the service life. 2. Minor maintenance generally refers to the routine maintenance items performed at the time or mileage specified by the manufacturer to ensure vehicle performance. It mainly includes changing the engine oil and oil filter. The interval for minor maintenance depends on the effective time or mileage of the engine oil and oil filter used. The validity periods of mineral oil, semi-synthetic oil, and full synthetic oil vary among different brands and grades.
10
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.