Can the Car's ECU Still Work After Getting Wet?

1 Answers
VanWalker
07/29/25 6:14pm
Generally, the car's ECU cannot function after getting wet. Below is relevant information about checking vehicle emission standards: Methods for checking vehicle emission standards: The vehicle's model number is usually indicated on the nameplate. Visit the Motor Vehicle Environmental Protection website, enter the fuzzy condition (vehicle model number) in the input box on the webpage, input the correct verification code, and click 'Query' to retrieve the vehicle's related information, including emission standards. How to locate the vehicle nameplate: There is usually a nameplate below the co-driver's door. Relevant labels displaying the vehicle model number can also be found in places such as the lower left corner of the front windshield, on the driver's door pillar, on the left side of the dashboard, in the engine compartment, on the adhesive side of the door, at the base of the door frame, or inside the glove compartment.
Was this review help?
15
0
Share
More Forum Discussions

How to Replace the Cabin Air Filter of Volkswagen Bora?

Volkswagen Bora cabin air filter replacement steps are as follows: 1. Unscrew the two exterior plastic screws. 2. Remove the sponge protective cover. 3. Push the filter bracket forcefully to detach it. 4. Take out the old filter and install the new cabin air filter. 5. Reassemble by reversing the removal steps. Additional information about cabin air filters: 1. The cabin air filter is crucial for vehicles and should be replaced regularly, recommended every 10,000 kilometers. 2. Regular cleaning of the air conditioning system is advised. Prolonged use can breed bacteria, potentially affecting passengers' health if left uncleaned.
7
1
Share

How to Check the Oil Dipstick on an Elysion?

The method to check the oil dipstick on an Elysion is: 1. Unscrew the dipstick and wipe it clean with a clean soft cloth or tissue. 2. Then reinsert it and pull it out again. There is an upper limit and a lower limit marked at the end of the dipstick. 3. Check the part of the dipstick that is wet with oil. (1) If the oil level is between the upper and lower limits, it means the oil quantity is just right. (2) If it does not reach the lower limit, it means the oil level is low. (3) If it exceeds the upper limit, it means there is too much oil. Additional information: 1. The function of the oil dipstick is not only to check the level of engine lubricating oil but also to detect many working dynamics of the engine; thus, it helps in maintaining the engine, identifying the causes of faults or accidents in time, preventing further deterioration of faults, and enabling quick responses and accurate judgments, providing reliable basis. 2. Regular oil dipsticks will have clear upper and lower limits. You just need to ensure that the detected oil level is between these limits. It is best if the oil level is in the middle. However, it should be noted that more oil is not always better. The higher the oil level, the greater the resistance of the engine. Ideally, the oil level can be maintained slightly below the middle position, where the engine's resistance is the smallest, fuel consumption is the lowest, and lubrication performance remains stable.
5
4
Share

How to Route the Alternator Belt for BYD Song?

The routing method for the alternator belt of BYD Song is as follows: 1. Before assembly, the final cleaning must be done with gasoline to ensure all parts are clean and dry, guaranteeing tight fitting surfaces free of oil and sufficient friction. 2. When assembling the hex socket head bolts, they should also be cleaned with gasoline and dried before assembly. Do not apply lubricating oil or grease to the bolts or threaded holes to ensure sufficient frictional self-locking capability after tightening. 3. When the three hex socket head bolts are nearly in place, tighten them alternately to ensure the taper sleeve is subjected to uniform axial force, guaranteeing good coaxial alignment between the pulley and the taper sleeve. 4. Before installation, measure the length of the hex socket head bolts used for assembly to ensure that after tightening, the bolts can press against the bottom of the blind hole in the taper sleeve, ensuring tight conical surface contact and that the bolts receive reverse thrust from the bottom of the blind hole, creating a locking effect similar to the double-nut principle. 5. After tightening the pulley, check and adjust the relative positions of the driving and driven pulleys with a tension gauge to ensure both pulleys are in the same plane and the belt is properly tensioned. 6. The pulley cover should be intact and securely installed to prevent serious safety accidents caused by belt breakage or pulley loosening during operation. 7. The taper sleeve is a wear-prone part. After prolonged operation, the inner hole and keyway may become damaged. Inspect it before each assembly and replace defective parts promptly.
12
4
Share

What is the 0-100 km/h acceleration time of the Bestune T77?

According to official data, the Bestune T77 with a 1.5L engine has a 0-100 km/h acceleration time of 11.2 seconds. Factors affecting a vehicle's 0-100 km/h acceleration time are as follows: Torque: Torque generally represents the strength of force. The greater the torque, the stronger the force pushing the vehicle, resulting in faster acceleration. The Lexus 2.0L naturally aspirated engine has a maximum torque of 208 Nm with a 0-100 km/h acceleration time of 12.5 seconds. The Bestune T77 1.5L has a maximum torque of 258 Nm with a 0-100 km/h acceleration time of 11.2 seconds. Transmission efficiency: The transmission acts as a medium for power transfer, inevitably involving power loss. Higher transmission efficiency leads to better acceleration performance. Generally, the ranking of transmission efficiency is: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. The Bestune T77 is equipped with either a 7-speed wet dual-clutch transmission or a 6-speed manual transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is called the power-to-weight ratio (unit: Hp/T). A higher power-to-weight ratio results in faster acceleration. The Lexus 2.0L naturally aspirated engine has a power-to-weight ratio of 107 Hp/T with a 0-100 km/h acceleration time of 12.5 seconds. The Bestune T77 has a power-to-weight ratio of 112 Hp/T with a 0-100 km/h acceleration time of 11.2 seconds.
15
1
Share

Can blue antifreeze and green antifreeze be mixed?

Blue antifreeze and green antifreeze cannot be mixed. This is because different brands and manufacturers use varying components and additive ratios. Although the main component is primarily ethylene glycol, the additives differ. Even antifreeze products from the same manufacturer may have different compositions if they are of different colors. Mixing them could lead to chemical reactions between the additives, rendering them ineffective. Antifreeze is a type of coolant with special additives, primarily used in liquid-cooled engine cooling systems. It offers excellent performance in preventing freezing in winter, boiling in summer, and protecting against scale and corrosion throughout the year. The main components of antifreeze are: 50% purified water, 40% methanol, and 10% other substances. It is generally categorized into three types: ethanol-water, glycerin-water, and ethylene glycol-water.
16
2
Share

How to Determine When to Change Car Engine Oil?

Methods to determine when to change car engine oil include the smell test, the rubbing test, the color test, and the light test. Below are detailed explanations of these methods: Smell Test: Pull out the dipstick and smell the oil. If there is a strong sour odor, it indicates the oil has deteriorated and should be changed. Rubbing Test: Take out some old oil and rub it repeatedly between your thumb and forefinger. Good-quality oil will feel smooth, produce little residue, and have no friction. If you feel impurities, poor viscosity, or even a gritty sensation, it's time to change the oil. Color Test: Place a few drops of old oil on a clean white filter paper. After the oil seeps in, good-quality oil will leave no powder, feel dry and smooth to the touch, and show a clear yellow stain. If the oil appears dark brown or black with visible impurities, it should be changed. Light Test: Hold the dipstick at a 45-degree angle and observe the oil droplets under light. Good oil will show no visible particles. If there are many particles, the oil should be changed.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.