Can the BYD F3 be used for Didi ride-hailing?

1 Answers
VanCaroline
07/30/25 2:18am
The BYD F3 can be used for Didi Express. The application requirements are as follows: 1. License plate requirements: The joining driver must own their own car with a local license plate. Additionally, the car must have a base price of over 70,000 RMB and be less than 8 years old. 2. Driving experience: The joining driver must possess a C1 or higher driver's license with at least 3 years of driving experience, be between 22 and 60 years old, and drive a vehicle that matches their permitted driving category when joining. 3. Personal requirements: The joining driver must hold an ID card, vehicle registration certificate, and driver's license simultaneously, have no bad records or criminal history, be in good health, capable of fulfilling duties, and have a strong sense of responsibility.
Was this review help?
15
4
Share
More Forum Discussions

Should the X-Trail's Vehicle Stability System Be Kept On Normally?

The X-Trail's vehicle stability system is enabled by default. The system monitors the vehicle's driving conditions through sensors. When the vehicle shows a tendency to skid during driving, the stability system applies braking to the corresponding wheels to prevent skidding. In situations where the vehicle needs to suddenly avoid an obstacle during an emergency turn, if the wheels lose traction and start to slip, the stability system intervenes by applying braking force to the skidding wheels, reducing the risk of rollover. Below is relevant information: 1. The vehicle stability system usually has a physical switch. It is recommended to keep the system enabled during normal driving, as it can help reduce the probability of traffic accidents to some extent. 2. When the vehicle is stuck in mud or sand, the ESP should be turned off. In such cases, the vehicle typically requires a sudden, strong application of throttle to provide sufficient power to escape. However, if the ESP is enabled, it will apply braking to the wheels, limiting the engine's RPM and making it more difficult for the vehicle to escape the predicament.
17
5
Share

How to Open the Car Fuel Tank Cap?

The following is an introduction to the methods of opening the car fuel tank cap: 1. Press-to-open type, which is the simplest method to open the fuel tank cap. When the vehicle is unlocked, the fuel tank cap can be opened by directly pressing it with your hand. When the vehicle is locked, the fuel tank cap cannot be opened. 2. Switch button type, where the fuel tank cap is controlled by a switch button inside the car. The location of this switch varies across different models. In some vehicles, the switch is located on the floor to the left of the driver's seat, while in others, it is designed as an electronic button placed on the door panel of the left front door or on the center console. The symbol for this is typically in the style of a fuel pump, and it can be found with a little attention. 3. Mechanical key type, which involves using a key to directly unlock the fuel tank cap. Alternatively, some cars have a press-type or directly openable outer cap, after which an inner cap needs to be opened with a key.
11
5
Share

What are the impacts of a damaged catalytic converter?

Here are the impacts caused by a damaged catalytic converter: 1. Excessive exhaust emissions: When the catalytic converter is clogged or fails, harmful gases such as CO, HC, and NOx are directly emitted, resulting in non-compliant exhaust emissions. 2. Increased fuel consumption: A clogged catalytic converter affects the normal operation of the oxygen sensor, which in turn affects the accuracy of the oxygen sensor signals received by the engine. This leads to inaccurate control of fuel injection, air intake, and ignition, naturally increasing fuel consumption. 3. Poor exhaust flow and reduced power: This is more noticeable in turbocharged models. When the catalytic converter is clogged, high-pressure exhaust flow is hindered, affecting air intake and causing a decrease in engine power. This results in reduced acceleration and a feeling of sluggishness while driving.
7
5
Share

Where is the Haval H6 radiator located?

Haval H6 radiator is located in the engine compartment, behind the intake grille, and connected to the coolant. The car radiator, also known as the heat exchanger, is the main component of the car cooling system; its function is to dissipate heat. The coolant absorbs heat in the water jacket, flows to the radiator to dissipate the heat, and then returns to the water jacket for circulation, achieving temperature regulation. It is an integral part of the car engine. Precautions for using the car radiator: 1. Wait until the engine has stopped working for a while before unscrewing the cap, otherwise there is a risk of being scalded by the coolant. 2. The added coolant must have the same specifications and parameters as the original coolant. 3. The amount added should neither exceed the MAX mark (upper limit) nor be lower than the MIN mark (lower limit).
20
0
Share

What does car tone mean?

Car tone refers to the audio settings on a car's sound system, specifically the tone button used to adjust sound effects such as midrange, treble, bass, rock, jazz, or symphony music. How to use: When using the car audio system, press and hold the tone button to find your desired sound effect. Note that operation methods may vary depending on the car model, so adjustments should be made accordingly. Usage tips: The car interior differs significantly from a room, acting more like a reverberation chamber for speakers. Therefore, avoid setting the tone too high as excessive treble can harm your ears. For a better music experience in the car, try activating the loudness function (e.g., LOUD). The loudness function works best when the music volume is low or the car is moving at high speeds, as tire and engine noise increases at higher speeds, making it harder to hear the audio clearly. Turning on the loudness function enhances the sound system's noise resistance, improving the overall music experience while driving.
13
4
Share

How to Update the Navigation System in Volkswagen Cars?

To update the navigation system in Volkswagen cars, follow these steps: 1. First, download the latest version of the car navigation APP and save it to a USB drive, then insert the USB into the car's USB port. 2. Enter the setting mode of the car's computer and uninstall the original map program. 3. Click on the downloaded map software in the USB drive, and when prompted for installation, click 'Install'. The program will automatically install in the original location. 4. After successful installation, open the application and enter the map interface. First, check if the positioning is normal and whether the GPS satellite search is successful.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.