Can Scratches on Car Window Glass Be Repaired?

What is the function of windshield wipers?

Windshield wipers are devices used to remove raindrops and dust attached to the vehicle's windshield, improving the driver's visibility and enhancing driving safety. The technical name for wipers is 'windshield wiper system,' which refers to the blade structure installed in front of the windshield, consisting of components such as an electric motor, reducer, four-bar linkage, wiper arm spindle, and wiper blade assembly. There are roughly two types of wipers: one is the traditional intermittent type, which is the more common wiper system, with three to four segments, adjusted by the driver according to the intensity of the rain and visibility conditions; the other is the rain-sensing type, mostly used in mid-to-high-end vehicle models.

1

Share

Where is the keyhole of the Roewe RX5?

Roewe RX5 does not have a keyhole, it features a one-button start system. The key of Roewe RX5 is used for opening the car door. Roewe RX5 key button instructions: one set includes one remote key and one mechanical key; the other set includes two remote keys. In terms of body dimensions, the Roewe RX5 measures 4545mm in length, 1855mm in width, and 1690mm in height, with a wheelbase of 2700mm. Roewe RX5 adopts the Blue Core high-efficiency power technology, equipped with two in-cylinder direct injection turbocharged engines, 2.0T and 1.5T, with a maximum power of 124kw and a peak torque of 250nm.

14

0

Share

What is the complete process of the Class B Subject 2 driving test?

Hill start, parallel parking, single-plank bridge, curve driving, right-angle turn, passing through a width-limited gate, stake test, narrow road U-turn, simulated highway driving, simulated emergency handling, continuous sharp turns on mountain roads, simulated emergency handling, simulated tunnel driving, and driving in rainy/foggy conditions. These are the complete procedures for the Class B driver's license Subject 2 test. Below are the detailed steps for each item in the Class B driver's license Subject 2 test: Stake Test: Reverse into Garage B from the starting point and stop properly, then move the vehicle twice forward and twice backward to transfer it to Garage A and stop properly. Proceed forward to exit Garage B to the control line, reverse into Garage A and stop properly, then return to the starting point. The vehicle must not stop during forward or backward movements, and the total time must not exceed 8 minutes. Parallel Parking: After parking the vehicle on the right side in front of the garage, reverse into the garage in one attempt without stopping. The wheels must not touch or cross the lane boundary lines or garage boundary lines. Single-Plank Bridge: During the test, the vehicle must not stop, and the wheels must not fall off the bridge. Narrow Road U-Turn: Drive the vehicle to the U-turn section and park on the right side. Complete the U-turn within no more than three forward and two backward movements. The test time must not exceed 5 minutes. Right-Angle Turn: Drive the vehicle along the designated route, making a right-angle turn from left to right or right to left in one attempt without stopping. The wheels must not touch or cross the lane boundary lines. Curve Driving: Commonly known as the S-curve. The test requires the vehicle to drive on an S-shaped road of specified width without pressing against the edge lines, with smooth steering control. This evaluates the driver's ability to maneuver the vehicle through curves. The goal is to develop the driver's steering skills and control over the vehicle's wheel tracks. Hill Start: Control the vehicle to stop accurately and start smoothly without rolling backward. The starting time must not exceed 30 seconds. Simulated Highway Driving: After entering the highway via the entrance ramp, turn on the left turn signal, look over the left shoulder to observe traffic, and accelerate into the lane after confirming safety. Drive at the minimum speed limit and turn off the signal. When changing lanes, turn on the turn signal for the intended lane, observe traffic, and change lanes after confirming safety. When exiting the highway, adjust speed and lane in advance according to exit signs. Simulated Emergency Handling: During normal driving, one of the following emergency situations will be randomly selected and simulated via voice or lights: If an obstacle suddenly appears ahead, brake immediately and stop quickly. After stopping, turn on the hazard warning lights. In case of a flat tire or other vehicle malfunction on the highway, slow down appropriately, observe following traffic, park the vehicle steadily on the emergency lane, turn on hazard warning lights, instruct passengers to move outside the guardrail, place warning signs correctly, and simulate calling for help from outside the guardrail. Simulated Tunnel Driving: Observe tunnel road signs before entering and follow instructions. Slow down when approaching the tunnel, turn on headlights, and honk. Honk again when exiting the tunnel and turn off headlights. Do not honk in no-honking zones. Simulated Rainy/Foggy Driving: Drive at reduced speed. In rainy conditions, adjust wiper speed based on rainfall. In foggy conditions, turn on fog lights, position lights, headlights, and hazard warning lights. Simulated Slippery Road Driving: Slow down before entering the slippery road. After entering, drive at low gear with steady speed and control the vehicle direction smoothly. Simulated Continuous Sharp Turns on Mountain Roads: Slow down before entering curves, drive on the right side, honk before entering the curve, and avoid occupying the opposite lane. Passing Through a Width-Limited Gate: Drive through three gates at a speed no lower than 10 km/h without touching the hanging poles.

9

1

Share

How to Remove Seafood Odor from the Car?

Odors in the car are mainly caused by dirty air conditioning components and mold due to moisture. The details are as follows: Odor caused by dirty air conditioning components: After years of use, dust accumulates inside the indoor filter and copper sheets of the air conditioner. When a certain amount of dust builds up, it produces an odor, which spreads into the air when the air conditioner is turned on. It is necessary to replace the air filter in time. Odor caused by mold due to moisture: After the air conditioner cools or heats, moisture often remains inside the indoor unit. If the air conditioner is turned off without a drying or anti-mold function, the moisture inside persists, leading to mold growth over time and causing odors in the car. It is necessary to clean the air conditioning ducts.

6

1

Share

How to Solve Low Car Battery Voltage?

To address low car battery voltage, the solution is to charge it as soon as possible using a portable charger. For example, the charging method for a 12V 80Ah battery is as follows: use constant voltage with current limiting for charging—charge at 14.8V constant voltage and 20A current limiting for 16 hours, then switch to 4A constant current for 4 hours, totaling 20 hours. When the battery is fully charged, the following phenomena will occur: 1. A large number of bubbles will be generated inside the battery, creating a boiling effect; 2. The terminal voltage will rise to its maximum and no longer increase within two hours; 3. The electrolyte level will rise to its highest point and no longer increase within two hours; 4. Observe the battery indicator—the indicator will show green when fully charged.

3

1

Share

What is the Composition of a Sedan Body?

Automobile body composition mainly includes: body shell, doors, windows, front sheet metal components, interior and exterior decorative parts, body accessories, seats, as well as ventilation, heating, cooling, and air conditioning systems. The body refers to the part of the vehicle used to carry passengers and cargo, and it also refers to the entire vehicle. The primary functions of an automobile body are to protect the driver and create a good aerodynamic environment. A well-designed body not only enhances performance but also reflects the owner's personality. In terms of structure, automobile bodies are mainly divided into two types: body-on-frame and unibody. Body-on-Frame: Vehicles with a body-on-frame structure have a rigid frame, also known as a chassis frame. The body is suspended on the frame and connected via elastic elements. The frame's vibrations are transmitted to the body through these elastic elements, with most vibrations being weakened or eliminated. In the event of a collision, the frame absorbs most of the impact force, protecting the body when driving on rough roads. As a result, the cabin experiences minimal deformation, offering good stability and safety, along with low interior noise. Unibody: Vehicles with a unibody structure lack a rigid frame. Instead, the front, side panels, rear, and floor are reinforced, with the body and base frame together forming a rigid spatial structure. In addition to its inherent load-bearing function, this unibody structure directly bears various loads. This type of body has high bending and torsional rigidity, is lightweight, has a low height, lowers the vehicle's center of gravity, simplifies assembly, and provides good stability at high speeds. However, since road loads are transmitted directly to the body through the suspension system, noise and vibration levels are higher.

14

2

Share

Can Scratches on Car Window Glass Be Repaired?

What is the function of windshield wipers?

Where is the keyhole of the Roewe RX5?

What is the complete process of the Class B Subject 2 driving test?

How to Remove Seafood Odor from the Car?

How to Solve Low Car Battery Voltage?

What is the Composition of a Sedan Body?

Can a dented car fender be pulled out?

Do automatic transmission cars have handbrakes?

What should the RPM be at 60 mph for a sedan?

Can I turn right when the straight signal is red?