Can motorcycles run in urban areas?

2 Answers
DiJames
08/31/25 5:53am
Whether motorcycles can enter urban areas depends on the specific regulations of each locality. Regulations on motorcycle restrictions in urban areas: During weekday morning and evening peak hours, from 7:00 to 9:00 and 17:00 to 20:00, motorcycles are prohibited from driving on the main roads, auxiliary roads, and roads within the Fifth Ring Road; from 9:00 to 17:00 on weekdays, motorcycles must comply with the city's tail number restriction regulations and the restricted areas. Legal basis for motorcycles entering urban areas: Traffic management departments of public security organs and their traffic police officers shall promptly correct road traffic safety violations. Traffic management departments of public security organs and their traffic police officers shall impose penalties for road traffic safety violations based on facts and relevant provisions of this law. For minor violations that do not affect road traffic, after pointing out the illegal act, a verbal warning shall be given before release.
Was this review help?
20
2
Share
DelAlejandro
09/13/25 2:20am
Motorcycles are definitely practical for urban commuting, especially in congested cities like mine. Riding a motorcycle saves me a ton of hassle during daily commutes. When cars are stuck in gridlock, a bike's agility lets me weave through traffic, saving significant time. Parking is also easier—small gaps suffice. However, be mindful of local restrictions: core zones in cities like Beijing and Shanghai ban motorcycles, and violations risk fines or impoundment. I recommend checking regional transport authority websites for permitted riding areas. Safety is critical—busy urban roads demand helmets and hi-vis gear due to higher accident risks. Maintenance-wise, frequent city riding accelerates wear; regular brake and tire checks prevent breakdowns. Overall, it's a cost-efficient, low-carbon option with cheap fuel costs, but slippery roads in rain or gusty winds require extra caution.
Was this review help?
17
5
Share
Expand All
More Forum Discussions

How to Prevent Rolling Back on a Slope

When starting a car on an uphill slope, due to the greater resistance encountered, the clutch should be held steady for 3-4 seconds longer than on a flat road. When releasing the handbrake, do not immediately release the clutch. Instead, immediately apply the accelerator and wait until the car moves slowly for 3-4 meters before gradually lifting the clutch to ensure a smooth start on the slope without stalling. When starting on an uphill slope and releasing the handbrake, immediately apply the accelerator to bring the engine speed to around 1500 RPM, ensuring sufficient power for the uphill start. Additional Information: 1. The main reason for rolling back is improper coordination between the accelerator and clutch in the semi-engaged state. Wheel spin is mainly caused by excessive throttle; rolling back is due to insufficient throttle or releasing the clutch too slowly; stalling often occurs when the clutch is released too quickly. During driving, we do not want the car to roll back, as it can easily lead to a "close encounter" with the vehicle behind or a wall. Therefore, to avoid such situations, it is best to hold the handbrake when starting the car. 2. When driving up a steep slope, always select an appropriate gear based on the slope conditions to maintain sufficient engine power. If the power is insufficient, quickly downshift without forcing it, as this may cause the engine to stall. If you miss the shifting opportunity, you can skip a gear to downshift. If you cannot shift or the engine stalls, immediately use both the foot brake and the parking brake to stop the car forcefully, then restart. If the car starts rolling back uncontrollably, steer the rear of the car toward the side of the mountain so that the rear touches the rocks and stops the car. Be careful not to turn the steering wheel incorrectly to avoid accidents. When driving on slippery slopes such as ice or mud, if the car ahead is climbing the slope, the following car should choose an appropriate spot to stop and wait until the car ahead has passed before climbing.
8
4
Share

What is the maximum speed of the Geely Xingrui?

Geely Xingrui accelerates from 0 to 100 km/h in 7.54 seconds. The following is a detailed introduction about vehicle speed: 1. Overview: Vehicle speed refers to the distance a car travels in a unit of time, referred to as speed, commonly measured in kilometers per hour or meters per second. Vehicle speed is one of the three parameters describing traffic flow and holds significant importance in traffic flow theory research. 2. Others: Vehicle speed can also generally refer to the speed of motor vehicles. To adapt to different purposes, vehicle speed is mainly divided into spot speed, segment speed, and design speed. Spot speed is the instantaneous speed of a car passing a specified point on the road. Design speed is the speed set to determine the design indicators of various geometric elements of the road and to coordinate them with each other.
13
4
Share

What is the function of the Mercedes-Benz car stopping when the brake is deeply pressed?

Mercedes-Benz car stopping when the brake is deeply pressed is the HOLD function which is turned on by default. The related introduction of Mercedes-Benz s600 is as follows: 1. Configuration: The autonomous driving system with distance radar device, independent air conditioning system for rear seats, elegant leather seats and wooden decorations have become standard configurations. 2. Power: Equipped with a new V12 engine with a displacement of 5.5 liters, the maximum power reaches 380 horsepower, the maximum torque is 830N-m, the 0-100km/h acceleration time is 4.6 seconds, and the maximum speed is 250km/h.
8
0
Share

What is another name for turbine oil?

Turbine oil is also known as TSA turbine oil. Here is some related extended information: 1. Turbine oil: It is a type of engine oil used for turbine engines, mainly employed in power plant steam turbines, hydroelectric station water turbine generators, and other scenarios requiring highly refined lubricating oil. It is suitable for high-speed machinery lubrication and primarily serves the functions of lubrication, heat dissipation, and cooling speed regulation. 2. Grades: Turbine oil is classified into several ISO viscosity grades, including 32, 46, 68, and 100. Its density varies with the kinematic viscosity of the turbine oil. The main parameter evaluated for turbine oil is kinematic viscosity, where dynamic viscosity/density = kinematic viscosity. The approximate density range of turbine oil is between 0.9 and 0.91.
2
2
Share

What are the common faults of the eighth-generation Civic?

Here are some common faults of the eighth-generation Civic: 1. Engine warning light on: The engine warning light keeps illuminating, which may be caused by signal errors due to aging of the engine control module. Solution: Have it repaired at a 4S shop. 2. Air conditioning not working: No air output, and the air conditioning compressor fails to start. The air conditioning system is not of great quality, and prolonged use may lead to aging of the air conditioning pressure switch. Solution: Replace with a new air conditioning system. 3. Abnormal gear shifting: Gear shifting impacts, sometimes stuck in one gear, and intermittent illumination of the engine warning light. This situation may be caused by dirty transmission oil. Solution: Conduct an inspection to eliminate the fault.
8
1
Share

What is the difference between gear oil 75w90 and 80w90?

The difference between gear oil 75w90 and 80w90 lies in their viscosity grades: Gear oils are classified into seven viscosity grades - 75W, 75W/90, 80W/90, 85W/90, 90, 85W/140, and 140 - based on their kinematic viscosity at 100°C and the maximum operating temperature when the apparent viscosity reaches 150,000 mPa.s. Relevant information about gears is as follows: 1. Introduction: A gear is a mechanical component with continuous meshing teeth on its rim that transmits motion and power. The application of gears in transmission systems dates back to ancient times. With the development of production, the smooth operation of gears has gained importance. 2. Gear teeth: Each protruding part on a gear used for meshing. Generally, these protrusions are arranged radially. The teeth of paired gears come into contact with each other, enabling the continuous meshing operation of the gears.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.