Can motorcycles park in motor vehicle parking spaces?

1 Answers
OJayla
07/28/25 6:21pm
Motorcycles can park in motor vehicle parking spaces. The full name of a parking space is motor vehicle parking space, and any motor vehicle recognized by the state is allowed to park there. Motorcycles are also a type of motor vehicle, and as long as they have legal license plates, they can park in these spaces. However, it should be noted that some public parking lots are only open to cars and prohibit motorcycle parking. Parking spaces can be categorized based on size and arrangement. Parking spaces are divided into two types by size: Large parking spaces: 15.6 meters long and 3.25 meters wide, suitable for medium and large vehicles. Small parking spaces: 6 meters long and 2.5 meters wide, suitable for small vehicles. Parking spaces are divided into three types by arrangement: Parallel parking spaces: Standard length is 6 meters, width is 2.5 meters. Angled parking spaces (30°, 45°, 60° angles): Diagonal length is 6 meters, width is 2.8 meters, with a vertical distance of 2.5 meters between the two diagonal lines. Perpendicular parking spaces: Length is at least 5 meters (usually set to 6 meters), width is 2.5 meters, with 2.5x5.3 meters being the optimal standard size. Large vehicle parking spaces should not use angled or perpendicular arrangements.
Was this review help?
18
5
Share
More Forum Discussions

How to Apply Car Wax?

Steps for applying car wax are as follows: 1. Wash and dry the car body thoroughly before waxing. Applying wax under sunlight will cause the softener in the wax to evaporate quickly, leading to rapid solidification of the wax's active ingredients, which is not conducive to full penetration. 2. Apply wax section by section according to the body panels. 3. Avoid waxing glass, black unpainted plastic parts, and rubber tires. 4. Use a sponge or soft cotton cloth to apply a small amount of wax in a dotted line pattern, then immediately use small circular motions to spread it evenly. Apply consistent and smooth pressure. Apply one row at a time and wipe it immediately. Keep the circles and rows as neat as possible, and avoid re-wiping areas that have already dried. For stubborn marks like scratches or paint stains, apply slightly more pressure to remove them. 5. After waxing the entire car body, open the doors and apply wax around the door frames. The inner parts of the hood and trunk lid do not need waxing. Tightly seal the used wax container to prevent evaporation and deterioration. Wax the areas near the car chassis last to avoid mixing in sand or gravel. 6. After the wax has dried for about half an hour, use a soft towel to wipe it off in the same order as the application. Ensure all windows and doors are closed during wiping to prevent dust from entering the car. After wiping, use a feather duster to remove any remaining dust.
7
3
Share

What Are the Reasons for Abnormal Noises When Starting a Car?

Abnormal noises when starting a car can be caused by the engine temperature being too low, thermal expansion of the car's three-way catalytic converter, transmission failure, or wear of the engine belt or chain. It is recommended to go to a 4S shop for maintenance and inspection to eliminate the fault. Reasons for abnormal noises when starting a car: Engine temperature too low: When the car is cold-started, the engine temperature is too low for it to work normally, and some abnormal noises are normal at this time. This is a normal phenomenon, and it will disappear as long as you wait a while for the engine temperature to rise to a normal level. Thermal expansion of the car's three-way catalytic converter: When there is an abnormal noise just after starting the car, it disappears after a while. This is caused by the thermal expansion of the car's three-way catalytic converter. It is also a normal phenomenon and can be ignored. Transmission failure: One of the reasons for abnormal noises when starting a car is transmission failure, which causes internal gears to rub and produce abnormal noises. This situation is more complicated and requires professionals at a repair shop or 4S shop to inspect it. Wear of the engine belt or chain: If the engine belt or chain is worn, it can also cause friction or abnormal noises due to idling when starting the vehicle. For safety reasons, it is best to replace the engine belt or chain directly in this case.
10
1
Share

Why is the car remote key not responding when pressed?

There are several reasons why a car remote key may not respond when pressed: 1. The remote key battery is dead; 2. The parking location has signal interference affecting the car; 3. There are signal jammers or criminals lurking nearby. A remote key refers to a key that utilizes the wireless remote control function of the central locking system, allowing doors to be unlocked or locked from a distance without inserting the key into the lock. It consists of two parts: a transmitter and a receiver. The working principle of a remote key is: first, the key emits a weak radio wave, which is received by the car's antenna. The electronic control unit then identifies the signal code, and the system's actuator performs the unlocking or locking action.
14
4
Share

Why Do Trucks Install BeiDou?

Trucks install BeiDou to monitor drivers' speeding, fatigue driving, and other illegal driving behaviors, assisting traffic control departments in investigations. Relevant details are as follows: 1. The BeiDou positioning for trucks refers to a software-based BeiDou satellite positioning recorder developed by contractors, commonly known as BeiDou, which is a type of positioning software. 2. National regulations require road transport vehicles to install the BeiDou positioning system, including passenger vehicles for highway operations, hazardous goods transport vehicles, semi-trailer tractors, and heavy-duty trucks. 3. There are three main reasons for BeiDou positioning failures in trucks: poor-quality recorders, weak signals from service providers, and human interference.
14
2
Share

What is the detection method for the accelerator pedal sensor?

Detection method: Remove the accelerator pedal assembly; locate the accelerator pedal position sensor; identify the signal output circuit corresponding to the accelerator pedal position sensor; use a multimeter in resistance mode to measure this circuit; operate the accelerator pedal while observing whether the multimeter readings change to determine if there is a fault; depending on the vehicle model, follow the specific measurement standard steps (refer to the repair manual). Inspection of the accelerator pedal position sensor: 1. External circuit inspection. Use the resistance mode of a multimeter to measure the resistance between each terminal of the APPS and the corresponding ECU terminal to determine if there are any short circuits or open circuits in the external wiring. 2. Sensor voltage measurement. Turn off the ignition switch, unplug the APPS sensor connector, turn the ignition switch to ON, and measure the voltage between terminals 1# and 2# of the harness-side connector and ground, which should be 5V, while terminals 3# and 5# should read 0V. 3. Sensor resistance measurement. Turn off the ignition switch, unplug the APPS sensor connector, and measure the resistance between terminals 5# and 6# on the sensor side, which should be 1.2±0.4KΩ, and between terminals 1# and 5#, which should be 1.7±0.8KΩ. 4. Data stream detection. Use the "X-431 fault diagnostic tool" to read the engine system data stream, which includes three data streams related to the accelerator pedal position sensor: "Accelerator Pedal 1 Potentiometer Voltage Value", "Accelerator Pedal 2 Potentiometer Voltage Value", and "Accelerator Pedal Opening Before Filtering".
2
5
Share

What Causes the Car Engine RPM to Fail to Increase?

Car engine RPM fails to increase due to: 1. Significant energy loss in power transmission between the engine and transmission; 2. Issues with the clutch and transmission; 3. Problems with the output shaft and gear engagement. The car engine is the power-generating device of a vehicle, serving as its heart, which determines the car's power performance, fuel efficiency, stability, and environmental friendliness. Depending on the power source, car engines can be categorized into diesel engines, gasoline engines, electric vehicle motors, and hybrids. Common gasoline and diesel engines are both types of reciprocating piston internal combustion engines, converting the chemical energy of fuel into mechanical energy of piston movement to deliver power output.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.