Can motor oil be used as fan lubricant?

1 Answers
JosiahLynn
07/29/25 12:55pm
Motor oil can be used as fan lubricant. Whether it's for cars or electric fans, motor oil can serve as a lubricant to reduce wear and tear. It's acceptable for temporary use, but specialized lubricants are required for long-term applications. However, excessive amounts should not be added during use. Related information: 1. Motor oil: Also known as engine lubricating oil, it serves multiple functions for the engine including lubrication and wear reduction, auxiliary cooling, sealing and leak prevention, rust and corrosion protection, as well as shock absorption. It's often referred to as the "blood" of automobiles. 2. Composition: Motor oil consists of base oil and additives. The base oil is the primary component of lubricating oil, determining its fundamental properties, while additives compensate for and improve deficiencies in the base oil's performance, imparting certain new characteristics. These additives form an essential part of lubricating oil.
Was this review help?
9
2
Share
More Forum Discussions

Should You Pull the Clutch When Turning a Motorcycle?

Motorcycle turning do not pull the clutch, pulling the clutch is usually accompanied by braking. In a curve, this can easily cause the tire to lock up and the bike to fall. Reasons for not pulling the clutch when leaning a motorcycle: When turning a motorcycle, you should first slow down, shift your center of gravity, and then turn the handlebars. Generally, you do not pull the clutch when turning, only reduce the throttle, and lightly pull or step on the brake to slow down. With the clutch engaged, you can use the throttle and brake to control the speed. When the clutch is disengaged, the bike is in an inertial state and cannot use the throttle to adjust speed, making it difficult to control. Therefore, it is generally not advisable to pull the clutch when turning. When you can pull the clutch on a motorcycle: If the curve is very sharp or the speed is not suitable for being too fast, you need to downshift or even stop, then you should pull the clutch. Shifting gears or stopping also requires pulling the clutch.
15
2
Share

What is the standard for interior noise at 120 km/h?

If the car speed reaches 120 km/h, the interior noise should be below 69 decibels to meet the standard. Normal car interior noise standards: Generally, the noise inside a sedan should be below 60 decibels to be considered normal. 40-60 decibels is the range for normal conversation. According to GB-1495-2002, the exterior noise limit for small cars (M1 category vehicles) is 74 dB(A) (decibels). Currently, there is no mandatory standard for car interior noise. Introduction to car interior noise: When a car is running, it generates noise, causing noise pollution both inside and outside the vehicle. Generally, interior noise mainly comes from engine noise, road noise, tire noise, wind noise, resonance noise, and other sources.
6
2
Share

Introduction to the Functions of Suzuki UY125 Dashboard Buttons

Suzuki UY125 has two dashboard buttons for the parking auto-lock function and auto start-stop function. Introduction to the Exterior of Suzuki UY125: The UY125 is a sturdy and durable model. Its length and wheelbase are slightly larger than those of scooters in the same class, giving it a spacious riding area with ample legroom and a well-balanced seating arrangement for both the rider and passenger. Introduction to the Handling of Suzuki UY125: The UY125's power delivery is strongest in the mid-to-high RPM range, where acceleration increases linearly, providing a very smooth acceleration curve. The throttle response is light and seamless, and the suspension offers pleasant surprises. In urban commuting scenarios, the preload and rebound tuning of the front and rear suspension are well-balanced, making its comfort level outstanding among scooters in the same class. In terms of handling, the UY125's frame tuning, suspension, braking, and throttle achieve a very harmonious match, delivering comprehensive performance.
2
4
Share

What is the small square in front of the car?

The small square below the car's headlights is the headlight cleaning device, used to clean dust from the surface of the headlights. There are two structural modes for the headlight cleaning device. Scrubbing system: Used for glass diffusers, because although plastic diffusers have wear-resistant coatings, they are still relatively sensitive to mechanical cleaning. This type of cleaning system can still be seen in older generation models. High-pressure cleaning system: Used on both glass and plastic diffusers. The cleaning effect mainly depends on the distance between the nozzle and the diffuser, the size of the water droplets, the contact angle, the speed of the water spray, and the amount of water sprayed.
19
1
Share

How wide is a lane in meters?

A two-way four-lane road is 2x7.5 meters, a two-way six-lane road is 2x11.25 meters, and a two-way eight-lane road is 2x15 meters. Meaning of lane width: Lane width (also known as standard lane width) refers to the width required for a single line of vehicles to travel safely and comfortably on the road, including the external width of the design vehicle and the necessary clearance for passing, overtaking, or parallel driving. Detailed explanation of lane width standards: The national standard specifies the width of each motor vehicle lane on highways. For multi-lane roads above the third grade, the width of each motor vehicle lane is 3.5-3.75 meters. There is no uniform standard for the central median strip, which is determined based on local conditions. A simple cement central median strip is one meter wide.
16
5
Share

What is the efficiency of gear transmission?

The efficiency of gear transmission is related to the type of gear, machining accuracy, and lubrication conditions. Generally, the efficiency of cylindrical spur gear transmission ranges from 0.9 to 0.99, with commonly used Grade 8 cylindrical spur gears achieving 0.97. For bevel gears, the efficiency ranges from 0.88 to 0.98, with commonly used Grade 8 bevel gears achieving 0.94 to 0.97. Definition of gear transmission: It refers to a mechanism that transmits motion and power through a pair of gears, and it is the most widely used mechanical transmission method in modern equipment. It offers accurate transmission ratios, high efficiency, compact structure, reliable operation, and long service life. Characteristics of gear transmission: High transmission accuracy. Belt drives cannot ensure precise transmission ratios, and chain drives cannot achieve constant instantaneous transmission ratios. However, the commonly used modern involute gears provide theoretically accurate and constant transmission ratios. This is not only a critical requirement for precision machinery and instruments but also an essential condition for reducing dynamic loads and achieving smooth transmission under high-speed and heavy-load conditions.
15
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.