Can Modified Brakes Pass Annual Inspection?

How to Coordinate the Clutch, Gearbox, and Accelerator?

The correct method for coordinating the clutch and accelerator involves the following steps: 1. Step One: During the starting phase, place the gear in neutral. After starting the engine, press the clutch pedal and shift the gear lever into first gear. Quickly lift the clutch pedal until the engine sound lowers (indicating the pressure plate and driven plate begin to engage), then slow down the release of the clutch pedal. 2. Step Two: As you slowly release the clutch pedal, feel the slight vibration and movement tendency of the vehicle. When the car shows slight vibration (indicating the clutch is semi-engaged) and begins to move, pause the clutch pedal briefly and simultaneously apply a small amount of throttle to prevent the engine from stalling. 3. Step Three: Continue to slowly lift the clutch pedal while gradually increasing the throttle with your right foot to ensure a smooth start. Once your left foot feels light, quickly and completely release the clutch pedal.

13

1

Share

How to Reset the Brake Pads on a BMW Mini?

Resetting the brake pads on a BMW Mini requires manual operation. First, insert the remote key without pressing the brake pedal, then press the start/stop button once to illuminate all dashboard lights. Methods for checking car brake pads: 1. Check the thickness: New brake pads are typically around 1.5cm thick. Over time, the brake pads will wear down. When the visible thickness is reduced to about 1/3 of the original (approximately 0.5cm), they need to be replaced promptly. Some vehicle models are designed in a way that makes it impossible to visually inspect the brake pad wear, requiring the removal of the tire for inspection. 2. Listen for sounds: During braking, if there are unusual noises accompanied by a metallic scraping sound when lightly pressing the brake, promptly check the wear level of the brake pads. If the brake pads have just been replaced, the noise might be due to the break-in period. 3. Feel the pedal: If the brake pedal feels harder to press during daily use, it may be due to severe wear of the brake pads. During emergency braking, if the pedal position feels noticeably lower, it could indicate that the brake pads have lost most of their friction, necessitating immediate replacement.

14

0

Share

How to Obtain a B1 License Now?

According to the relevant regulations for driver's license application, a B1 driver's license can only be obtained through an additional driving test. Before applying for the B1 license, you must have held a license for driving urban buses, small cars, small automatic transmission vehicles, low-speed trucks, or three-wheeled vehicles for more than three years; or have held a license for large trucks for more than two years. Additionally, you must not have accumulated 12 penalty points in any of the last three scoring cycles prior to the application. Here is some additional information: 1. Test Subjects: The B1 license test consists of Subject 1, Subject 2, and Subject 3. Subject 1 is a test on traffic and road regulations, similar to the Subject 1 test for a C1 license; Subject 2 is a skills test on a closed course, equivalent to the Subject 2 test for a C1 license; Subject 3 is a road test, just like the Subject 3 test for a C1 license. 2. Annual Review Cycle: The B1 license requires an annual review. If no penalty points are accumulated during the scoring cycle, the annual review can be waived. If there are penalty points, you must attend a safety training session during the annual review. If you are over 60 years old, an annual review is required even if no penalty points are accumulated.

17

2

Share

Is it useful to apply sealing strips to a car?

Applying sealing strips to a car is useful. Sealing strips can serve functions such as windproofing, leak prevention, and vibration reduction, reducing noise during car operation. There are various types of sealing strips, including water cut, door frame, door opening, engine hood, trunk, sunroof, front and rear windshields, as well as some decorative strips. More information about car sealing strips is as follows: 1. Installing car sealing strips can relatively improve the sound insulation effect of the car, and the sound of closing the door will appear more solid. 2. It will enhance the sealing effect of the car. Whether in summer or winter, air conditioning is used when driving the car. Therefore, only by installing car sealing strips can the sealing effect be better, and in summer, there is no need to worry about the cold air escaping.

11

5

Share

How to Test the Condition of an Ignition Coil?

Checking whether an ignition coil is in good condition can be done on the machine. The specific steps are as follows: 1. Turn on the ignition switch, and after confirming that the low-voltage circuit is normal, pull out the high-voltage wire from the center of the distributor cap, keeping it 3-5mm away from the cylinder block. Use a screwdriver to toggle the distributor contacts, continuously opening and closing them. If a blue-white spark jumps between the high-voltage wire and the cylinder block with a crisp sound, it indicates that the ignition coil is functioning well. 2. If there is no spark and the high-voltage wire is confirmed to be normal, it means the ignition coil has failed. 3. During engine operation, the condition of the ignition coil can also be judged by temperature. A slightly warm coil is good, while a scalding hot one is faulty or damaged. Additionally, installing the suspected ignition coil on an engine with a fully functional ignition system for a spark test can help determine its condition.

3

0

Share

What does the hill start assist function mean?

The hill start assist system is a function developed based on the ESP system, which prevents the vehicle from rolling back when starting on a slope. Here is a detailed introduction about hill start assist: 1. The hill start assist function temporarily applies braking to all four wheels to prevent the vehicle from rolling back: When starting on a steep or slippery slope, the driver switches from the brake pedal to the accelerator pedal, which may cause the vehicle to roll backward, making it difficult to start. However, with hill start assist control, the vehicle is prevented from rolling backward, allowing the driver to start easily and operate the pedals smoothly. 2. The hill start assist function has activation conditions: (1) The gear lever is not in the P position (for automatic transmission models), and the accelerator pedal is not pressed. (2) The vehicle must be in a stationary state. (3) The driver has not engaged the handbrake, footbrake, or electronic brake.

2

Share

Can Modified Brakes Pass Annual Inspection?

How to Coordinate the Clutch, Gearbox, and Accelerator?

How to Reset the Brake Pads on a BMW Mini?

How to Obtain a B1 License Now?

Is it useful to apply sealing strips to a car?

How to Test the Condition of an Ignition Coil?

What does the hill start assist function mean?

Do I Need to Go in Person for Driver's License Renewal?

Can Run-Flat Tires Be Used on Any Car?

How many days after applying the film can I roll down the windows?

Where is the spare tire of GAC Trumpchi GM8 located?