Can I Wear Glasses During the Driver's License Physical Examination?

1 Answers
OLeila
07/30/25 4:30am
It is acceptable to wear glasses if you have difficulty seeing during the physical examination. If you wear glasses for the photo taken during the examination, you must also wear them during the actual driving test. This is because the examiner will photograph the test process, and failing to comply with this rule may result in disqualification. Therefore, it is advisable to maintain the same appearance during the test as during the physical examination. According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," applicants for a Class C driving license must have a naked or corrected visual acuity of at least 4.9 on the logarithmic visual acuity chart, while applicants for Class A or B licenses must achieve a visual acuity of 5.0 or higher. Therefore, individuals with myopia or hyperopia can meet the required vision standards by wearing glasses during the physical examination.
Was this review help?
15
0
Share
More Forum Discussions

Can the Avalon use 95 octane gasoline?

Avalon can use 95 octane gasoline, with 92 octane being the minimum requirement. Using 95 octane gasoline poses no issues. Gasolines with different octane ratings contain varying levels of octane - higher-rated fuels have greater octane content. Gasoline is a volatile, flammable hydrocarbon mixture liquid distilled or cracked from petroleum, primarily used as fuel for spark-ignited internal combustion engines. The Avalon is a mid-size 4-door 5-seater sedan under FAW Toyota, measuring 4975mm in length, 1850mm in width, and 1450mm in height, with a 2870mm wheelbase, equipped with an 8-speed automatic transmission.
11
2
Share

Does the Audi S3 have a launch control mode?

The Audi S3 is equipped with a launch control mode. Here are the relevant details: 1. The Audi S3 is a performance car. It is powered by a third-generation EA888 engine, which is a 2.0-liter turbocharged engine. This engine delivers 290 horsepower and 380 Nm of maximum torque. It can output maximum power between 5,400 and 6,500 rpm and maximum torque between 1,850 and 5,300 rpm. The engine features hybrid injection technology and uses an aluminum cylinder head with an iron cylinder block. 2. The Audi S3 is paired with a 7-speed dual-clutch transmission, which is highly suitable for performance vehicles. Dual-clutch transmissions offer fast gear shifts and high transmission efficiency. The Audi S3 also comes with a full-time all-wheel-drive system, which provides excellent mechanical grip and enhances straight-line acceleration performance. 3. The Audi S3 features a MacPherson independent front suspension and a multi-link independent rear suspension. The car boasts an attractive exterior design and a well-crafted interior.
17
0
Share

How to Identify Whether a Car is New?

Methods to identify a new car: 1. Check the manufacturing date: If you encounter a model with a long service life but exceptionally low mileage, there might be an issue with this car. 2. Examine tire wear: New tires have computer-like lines on the tread surface and hair-like protrusions on the sidewalls, which usually wear off after 50-100 kilometers. 2. Inspect brake pad wear: New cars or those driven very short distances show minimal wear; significant wear indicates more usage, even if the odometer shows low mileage. 3. Look at the interior: Seats that have been sat on for extended periods lose elasticity and appear shiny and hard; if the pedals, floor mats, and steering wheel look brand new, these parts may have been replaced. 4. Check the engine bay: Areas that accumulate dirt and are hard to clean in cars that have been driven for some time.
6
4
Share

Does replacing the front windshield affect the car?

Proper replacement of the front windshield does not affect the car; however, improper installation may cause the adhesive and the windshield to not fit tightly on both sides, which could have an impact. Below are some related details: 1. Improper replacement of the front windshield may result in wind leakage through the gaps between the windshield and the car body during high-speed driving, increasing interior noise. When driving on bumpy roads, there may be rattling or knocking sounds from the front of the car. 2. After replacing the front windshield, to prevent wind or water leakage, avoid washing the car for three days and remove the adhesive tape securing the windshield only after three days. Try to avoid driving on excessively bumpy roads to prevent the windshield from shifting. 3. After replacing the rear windshield, do not open the windows while driving for the first three days to prevent the rear windshield from shifting due to wind pressure.
13
5
Share

What transmission model does the Lynk & Co 03 use?

Lynk & Co 03 uses a 6-speed manual transmission, 6AT transmission, and 7-speed dual-clutch transmission models. The transmission is an automotive component used to alter the speed and torque from the engine, and it can either fix or change the gear ratio between the output and input shafts. The transmission consists of a gear transmission mechanism and a control mechanism, and can be categorized into stepped, continuously variable, and integrated transmissions. It functions include enabling reverse driving, interrupting power transmission, and changing gear ratios. The Lynk & Co 03 is a compact 4-door 5-seater sedan with dimensions of 4639mm in length, 1840mm in width, and 1472mm in height, and a wheelbase of 2730mm, equipped with a 6-speed manual transmission.
5
4
Share

What is the meaning of vehicle clearance lights?

Vehicle clearance lights are the outermost lights located at the front and rear of a vehicle, serving as warning indicator lights to alert other vehicles. These lights are installed along the top edges of the vehicle, indicating both the height and width of the car. Safety regulations mandate that vehicles exceeding three meters in height must be equipped with clearance lights. The clearance lights are white at the front and red at the rear, designed to enhance visibility for other vehicles during nighttime driving. Other lighting systems on vehicles include: low beam and high beam headlights, commonly referred to as "headlights". The difference between high beam and low beam lies in their nighttime illumination functions - high beams project light at a higher angle with longer range, while low beams emit light at a lower angle with shorter range.
2
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.