···
Log in / Register

Can I transfer to another driving school if I have already paid the previous one?

1 Answers
DeEliza
07/29/25 8:56pm
Can I transfer to another driving school if I have already paid the previous one? The following is a detailed introduction about transferring driving schools: Payment: Transferring to another driving school requires paying again, as driving schools are not only unrelated but also in competition with each other. Therefore, paying again when transferring is inevitable, which means establishing a new training relationship with the new driving school. Considerations: The most important point is that if you have already passed subjects like Subject 1 or other tests at the original driving school, you will need to retake these exams at the new driving school. The time and effort wasted should be carefully considered before making the decision to transfer. Refund: The amount of tuition refunded by the original driving school is not a fixed value, and there are no relevant laws or regulations specifying the refund ratio when transferring driving schools.
Was this review help?
6
0
Share
More Forum Discussions

How to Deal with Intake Camshaft Position Fluctuation in Roewe 350?

Install a dial indicator in the thrust direction at the front end of the camshaft to measure whether the axial end clearance indicated by the dial when the camshaft moves forward and backward (axially) is normal. The limit value for camshaft end clearance is 0.1~0.2mm. If it exceeds this value, you can reduce the thickness of the spacer ring or replace the thrust collar. For fluctuations caused by a faulty camshaft position sensor, simply replace it with a new one. Check if the timing chain is loose, as a loose chain can cause gear misalignment, leading to camshaft fluctuation.
12
4
Share

How to Turn on the High Beam on a CRV?

Carry the key close to the car (within two meters) to unlock the door. After entering the driver's seat, gently press the one-touch start button to power on the vehicle and initiate self-check. On the lower left side of the steering wheel, there is a turn signal lever. The outer part is the headlight and position light switch. Turn the knob to the bottom position to turn on the headlights. The headlights turned on at this time are low beams. In this state, push the lever downward to activate the high beams. After turning on the low beams, pull the light control lever backward to momentarily activate the high beams, also known as flashing the high beams or alternating between high and low beams.
18
0
Share

How to Remove the Door Panel of an Old Jetta?

First, prepare the tools: one flat-head screwdriver, one Phillips-head screwdriver, and one T30 wrench. Unscrew the door handle counterclockwise, remove the inner door handle, pry open the plastic cover from below using the flat-head screwdriver, then loosen the two screws inside with the T30 wrench. Remove the three Phillips-head screws on the door edge; forcefully push open the locking clip of the handle frame (push outward toward the door), then push along the arrow direction to complete the removal. Forcefully remove the rearview mirror adjustment knob, unplug the control button wiring harness connector inside the Jetta door panel. Lift the door panel off the bracket. Forcefully pull open the clips to remove the door panel.
16
0
Share

What is the solution for oil burning in a 2015 Peugeot 408?

For a 2015 Peugeot 408 experiencing oil burning, you can increase the sealing between the engine pistons and cylinder walls by switching to a higher viscosity oil or regularly inspecting and replacing relevant oil system components. Symptoms of oil burning: Blue smoke during cold starts indicates minor oil burning. If you observe large amounts of blue smoke from the exhaust pipe, this signals significant engine oil burning. A very black exhaust pipe interior wall is another indicator. Preventive measures for oil burning: Use high-quality engine oil. Oil tends to corrode and degrade under prolonged high temperatures, thinning the oil film and making it easier to enter the combustion chamber. Using premium quality oil can significantly delay this phenomenon.
15
4
Share

How to route wires from outside to inside the car for Magotan B7?

Open the hood of the Magotan B7, locate the firewall on the partition between the hood and the driver's seat, and make a hole in the rubber plug, which serves as the passage for the wire harness. Open the glove box, find the fuse box of the Magotan B7 inside, where there will be spare fuse positions. Connect the external wire harness's fuse circuit to the spare fuse. After connecting the wires, organize the wire harness properly, cover it with protective caps, ensure waterproofing, and secure the wire harness in the appropriate position on the car using fastening clips. After debugging and confirming normal operation, seal the rubber plug wire harness hole with silicone sealant, remove any excess sealant, and finish with aesthetic treatment.
17
4
Share

What to Do If the Geely Vision Car Key Is Lost?

When taking delivery of the car, the 4S dealership will provide the owner with two keys, one of which is a spare key. If a key is lost, the first step is to locate and use the spare key. Call a professional locksmith company and request them to send a technician to assist with unlocking the car. You will need to provide identification documents such as an ID card and driver's license. Most 4S dealerships now offer emergency rescue services. Contacting the dealership will help get the car door opened and arrange for a new key to be made. The Geely Vision car key consists of a remote control and a mechanical key. Identical models are available for purchase online. After purchasing, the owner can follow the instructions to self-match the key.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.