Can I Take the Subject 4 Test with an Expired ID Card?

1 Answers
LeElaina
07/29/25 6:10pm
To enter the Subject 4 examination room, verification is required. You must present the original of a valid ID card or the original of a valid temporary ID card to enter the examination room and take the test. If your ID card has expired and you want to take the Subject 4 test, you can: 1. Go to the public security bureau to apply for a temporary ID card. 2. A temporary ID card can be issued at any public security bureau, regardless of whether it is in your local area or elsewhere. Relevant information about Subject 4 is as follows: 1. Subject 4: Also known as the Subject 4 theoretical test or driver's theoretical test, it is part of the motor vehicle driver's license assessment. 2. Test paper: Consists of 50 questions, mainly in the form of cases, pictures, animations, etc., with a full score of 100 and a passing score of 90.
Was this review help?
18
2
Share
More Forum Discussions

How to turn off the navigation in Haval H6?

Haval H6 navigation shutdown method: On the navigation interface, select the second option at the bottom labeled 'Route', then choose the last option 'Turn off navigation'. Alternatively, you can directly click 'Cancel navigation'. The car GPS navigation system consists of two parts: one part is the GPS receiver and display device installed in the car, and the other part is the computer control center. The Haval H6 is equipped with a 12.3-inch full LCD instrument panel, electronic handbrake, automatic parking, car-to-phone connectivity, human-machine interaction system, dual-zone automatic air conditioning, smart keyless entry, one-button start. In terms of body size, the Haval H6 measures 4649mm in length, 1852mm in width, 1710mm in height, with a wheelbase of 2680mm.
5
0
Share

How to reset the maintenance light on Peugeot 3008?

The method to reset the maintenance light on Peugeot 3008 is as follows: 1. Turn off the ignition switch. 2. Press and hold the maintenance mileage reset button. 3. Press the one-touch start button, and the odometer display will begin the countdown. 4. When the display shows "=0", it means the maintenance indicator light has been successfully reset. 5. After releasing the reset button, the wrench symbol (maintenance indicator light) will turn off. More information about the Peugeot 3008 is as follows: 1. In terms of power, the domestically produced 3008 offers two engine options: 2.0L and 1.6T. 2. The 2.0L model provides two transmission choices: a 6-speed automatic manual transmission and a 5-speed manual transmission.
13
2
Share

Can Water Be Used to Cool Tires During Long-Distance High-Speed Driving?

Long-distance high-speed tires should not be cooled with water. The correct approach is to stop the vehicle immediately and wait for the brake drums or tires to cool down naturally before continuing. Otherwise, it may lead to brake failure, increased tire wear, or even a tire blowout. Avoid the temptation to save time by splashing cold water, as this can cause the tires and friction linings to delaminate or crack, and the brake drums to deform due to uneven cooling. Here are some relevant tips: Avoid prolonged driving; take appropriate breaks during long trips to reduce fuel temperature. Monitor the water temperature to prevent overheating, which can also cause the engine to stall. If the engine stalls frequently during the journey, park the vehicle in a safe location, open the fuel filler cap and the engine hood for about half an hour before restarting. Most importantly, listen for any abnormal noises from the fuel pump. If none are heard, you can continue driving normally.
2
3
Share

What is the reason for resonance around 1200 RPM in a BMW 5 Series?

Tire tread wear and unevenness can cause resonance sounds due to friction and impact between the tire and the ground, which are transmitted into the cabin along with vibrations from the fender and mudguard. In this case, soundproofing materials should be added to areas such as the doors, fenders, and mudguards to reduce noise. More related information is as follows: 1. If the car engine shakes severely while driving and sometimes fails to start, it may be due to a dirty throttle or excessive carbon buildup in the fuel injector and intake manifold. In cold conditions, carbon deposits can absorb some fuel, and if the fuel does not fully enter the cylinder for combustion, it can cause unstable idling and difficulty starting. 2. When driving at a certain speed on the highway, the steering wheel may noticeably shake or vibrate, but this is not obvious at low speeds. In fact, there are many reasons for engine shaking. Here, we first need to rule out abnormal shaking caused by engine faults, as engine issues usually also occur at low speeds.
10
0
Share

What is the function of the shark fin on a car?

The functions of the shark fin on a car are as follows: 1. Safety: It overcomes the shortcomings of traditional telescopic rod antennas, whip antennas, and car glass antennas, integrating all the functions of a conventional antenna with the latest modern electronic technology. The built-in safety and anti-theft structure effectively prevents antenna theft, offering a higher safety factor. 2. Powerful functionality: The shark fin car antenna integrates various powerful automotive electronic functions such as FM, GPS, and GSM, effectively combining "fashion" with "functionality" to achieve perfection. 3. Noise reduction: Combining aerodynamic principles and aesthetic principles, it effectively reduces airflow noise, making driving quieter. 4. Convenience: It eliminates the need to remove the antenna during automatic car washes or when entering spaces with limited clearance, saving time and hassle. 5. Static reduction: The shark fin antenna fully utilizes the characteristics of electronic discharge at the tip, directing static electricity to the tail tip of the shark fin antenna for release. No matter where the shark fin antenna is installed on the car, it can effectively reduce static electricity on the car's surface.
11
4
Share

Is Wheel Rotation Used for Dynamic Balancing?

Wheel rotation, if it involves swapping the front and rear tires of a vehicle, does not require dynamic balancing. This is because the process only involves the removal and installation of the wheel assembly, not the disassembly and reassembly of the tires. Dynamic balancing is only necessary when the tire and rim are reassembled, such as when replacing the rim, changing the tire, repairing a puncture, installing a tire pressure monitoring module, or switching to valve stems made of different materials. Dynamic balancing not only eliminates the force couple caused by dynamic imbalance but also removes the centrifugal force from static imbalance. Therefore, it can be used to balance various cylindrical rotors, such as those in centrifugal compressors or large electric motors.
2
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.