Can I Take the Subject 2 Test at a Different Test Center?

1 Answers
LeAngelina
07/24/25 10:13am
It is possible to schedule the Subject 2 test at a different test center. Currently, the driver's license test system is interconnected across various districts within the city, allowing students to choose their preferred test venue and register online. Subject 2 Test Scheduling Methods: The driving school can assist students in scheduling the test, or students can independently schedule it online. The scheduling for the Subject 2 test is arranged based on the total number of applicants for that day. Subject 2 Test Notes: Before the test, wear comfortable clothing and prepare mentally. When reversing into the parking space, pay attention to key points—avoid turning left or right. During parallel parking, ensure the rear wheels do not cross the edge line of the parking space, adjust the distance properly, and remember to use the turn signal and honk. For the 90-degree turn, steer sharply once the reference point is aligned. During the curve driving, make wide turns after entering the curve, maintaining a steady speed. Avoid crossing any lines during these maneuvers. After completing the test, drive the car back to the starting position, sign the confirmation, and then turn off the engine. Mock Test: The purpose of the mock test is to familiarize candidates with the test environment and allow the instructor to point out areas where points are easily deducted. When attending the test, be sure to bring your ID card. Without it, you cannot take the test. Ensure your phone is turned off during the test, as any sound from the phone may be considered cheating.
Was this review help?
11
5
Share
More Forum Discussions

What Causes the Transmission Noise in the Volkswagen New Santana?

Reasons for transmission noise in the Volkswagen New Santana: transmission failure or issues with the oil quality. Here are the specific reasons: Transmission failure: There are many causes for transmission failure, such as valve body damage or wiring harness short circuits. It is recommended to have a professional technician conduct an inspection. Transmission problems can manifest in various ways, including transmission noise, slipping, or oil leaks, and should be addressed based on the actual situation. Issues with oil quality: Water and sludge in the fuel tank can be a problem. Therefore, it is advised to refuel only at reputable gas stations. When traveling, you can use a gauze wrapped around the fuel nozzle to filter out impurities.
6
4
Share

Where is the chassis number of Bora located?

There will be an identification plate that records the 17-digit chassis number of the vehicle. Additionally, the chassis number information is also recorded on the vehicle's model plate, commonly found in locations such as the left side of the dashboard and the engine compartment. Composition of the automobile chassis: The automobile chassis consists of four parts: the transmission system, the running gear, the steering system, and the braking system. The role of the chassis is to support and install the automobile engine and its various components and assemblies, forming the overall shape of the automobile, receiving the power from the engine to enable the automobile to move and ensure normal driving. Composition of the transmission system: The transmission system generally consists of the clutch, gearbox, universal transmission device, main reducer, automobile chassis, differential, and half shaft.
7
1
Share

Does the Borui belong to the B-segment car?

Geely Borui belongs to the B-segment car, which is a mid-size car. A-segment car: A-segment car refers to small cars, such as Focus and Corolla. The body length of cars in this segment is between 4.3-4.79 meters, the wheelbase is 2.35-2.79 meters, and the engine displacement is generally between 1.4 liters and 2.0 liters. B-segment car: B-segment car refers to mid-size cars, such as Accord, Passat, Camry, etc. The wheelbase is between 2.7 meters and 3.0 meters, the body length is generally between 4.8 meters and 5.0 meters, and the engine displacement is generally between 1.5 liters and 2.5 liters.
19
0
Share

What is the wading depth of the Mazda CX-4?

The maximum wading depth of the Mazda CX-4 is 400mm. The wading depth of the Mazda CX-4 is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when driving through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a reference when passing through waterlogged roads. If the air intake of the Mazda CX-4 is below the water level while wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth must not exceed the height of the engine's air intake. Installing a snorkel can increase the height of the engine's air intake, thereby improving the maximum wading depth. If wading is unavoidable, the following safe and correct operations should be performed: Before the vehicle enters the water, always turn off the auto start-stop function to prevent the engine from automatically restarting after stalling in the water, which could cause severe damage due to water ingress. Assess the underwater road conditions based on the passage of preceding vehicles, choose an appropriate entry point, and follow the path taken by other vehicles at a low speed. Avoid sudden acceleration or deceleration. On roads prone to water accumulation, observe warning water level markers, trees, or other vehicles' wheels and doors as references to judge the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half of the tire height or the engine's air intake, avoid entering the water and choose an alternative route.
12
2
Share

Where is the oil dipstick for the Mercedes-Benz 264 engine?

The oil dipstick for the Mercedes-Benz 264 engine is located under the hood, inside the engine compartment, next to the small coolant reservoir. Method for adding engine oil: Reinsert the oil dipstick into the dipstick tube, then pull it out again to check the oil mark on the dipstick. Under normal circumstances, the oil mark should be between the upper and lower notches on the dipstick, slightly above the middle line. If the oil mark is below the lower notch, it indicates insufficient oil and requires immediate refilling. While adding oil, continuously pull out the dipstick to monitor the oil level. Hazards of excessive engine oil: Excessive oil can enter the combustion chamber through the gap between the cylinder and piston, where it burns and forms carbon deposits. If too much carbon accumulates, it can easily cause engine knocking. Excessive oil also increases the movement resistance of the crankshaft and connecting rod, leading to higher fuel consumption.
16
2
Share

What is the recommended tire pressure for Corolla in summer?

Toyota's new Corolla summer standard tire pressure recommendation is 2.3bar for the 1.6L displacement model when the tires are cold, while the 1.2T and 1.8L displacement models recommend 2.4bar cold tire pressure. These cold tire pressure values are applicable for both summer and winter tires. Tire pressure is related to seasons: Tire pressure is safe within a certain floating range (usually 10%) of the factory calibration value. For current civilian car tires, the generally acceptable safe tire pressure range is between 2.0-2.8bar. In winter, the tire pressure should be based on the standard tire pressure of the car tires, with an appropriate increase of about 0.2bar. In summer, it should be about 0.1bar lower than the standard. These adjustments are to prevent tire blowouts. Tire pressure measurement environment: The tire pressure of cold tires and hot tires is different, with a difference of about 0.2bar between them. Measure the tire pressure at least three hours after parking or when the tires have not been driven more than 2 kilometers. If you can only measure the tire pressure when the tires are hot, subtract approximately 0.2bar from the measured value to get the cold tire inflation pressure.
17
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.