···
Log in / Register

Can I Shift to Neutral to Rest My Feet During Subject 2 Test?

1Answers
SanEmersyn
07/24/2025, 10:12:59 PM

Shifting to neutral to rest your feet is not allowed during the Subject 2 test. Only first gear and reverse gear can be used throughout the entire examination. Below are specific details about Subject 2: Subject 2 Test Attempts: Candidates have one initial test attempt for Subject 2. If they fail, they are allowed one retake, totaling two opportunities. If the retake is not attended or the candidate fails again, the examination process ends, and the applicant must reschedule the test after ten days. Within the validity period of the driving skill test permit, the number of Subject 2 test reservations must not exceed five times. Subject 2 Test Content: The examination includes reverse parking, hill start and stop, parallel parking, curve driving, and right-angle turns (Note: Some regions include a sixth item—highway toll card collection).

Was this review help?
105
Share
More Q&A

How to remove the air filter of Lavida?

Method for removing and replacing the air filter: 1. There is a black plastic panel on the upper part of the passenger footwell with two retractable clips. Press the clips to remove the panel. 2. Then disconnect the negative terminal of the battery, remove the body computer, and take off the bracket that holds the body computer. 3. Next, remove the panel on the left side of the passenger footwell, which is secured by four screws, and then proceed with installation. Below is some relevant information: The function of the air filter is to prevent such substances from entering the air conditioning system and damaging it. The filter also efficiently filters and adsorbs particulate impurities, achieving oil filtration and air purification performance, while effectively removing organic gases such as TVOC, benzene, phenol, ammonia, formaldehyde, xylene, and styrene. It is an ideal material used as an automotive air filter in various high-end cars, sedans, and commercial vehicles.
103
Share

How to Read the Oil Dipstick on a Volkswagen?

Here are the steps to check the oil dipstick on a Volkswagen: 1. Park the car on a level surface and open the front hood. 2. Remove the oil dipstick and wipe the oil edge clean with a clean cloth. 3. Reinsert the dipstick all the way back into the engine, wait a few seconds, then pull it out again. 4. Observe the section of the dipstick that is wet with oil to accurately measure the oil level. Below is an introduction to the oil dipstick's location: 1. The oil dipstick is generally located near the engine. 2. When you open the front hood, you will find a yellow pull ring on the left side of the engine, which is the oil dipstick. 3. The oil dipstick is a commonly used measuring tool to check the static oil level height, thereby indicating whether the engine oil level is within the reasonable range.
116
Share

How to Use a Volkswagen Jack?

The method for using a Volkswagen car jack is as follows: 1. Position the car jack under the vehicle. 2. Raise the car until the wheel is just off the ground. 3. Remove the loosened wheel bolts and place them on a clean pad (such as a wheel cover, cloth, paper, etc.) next to the jack, then take off the wheel. 4. Install the spare wheel and slightly tighten all the wheel bolts. Introduction to the jack: 1. A jack is a light lifting device that uses a rigid lifting component as the working device to lift heavy objects within a small stroke through a top support or bottom claw. 2. Jacks can be divided into three types according to their structural characteristics: rack jacks, screw jacks, and hydraulic (oil pressure) jacks.
115
Share

How to Lift Up the Wiper Blades on a Tiguan?

Insert the key and start the ignition, then push the wiper control lever downward. After removing the key, the wiper blades of the Tiguan can be lifted up. Below are the detailed steps for installing the wiper linkage rod: 1. Remove the wiper blade, open the hood, and unscrew the fixing screws on the cover plate. 2. Bend back the hood seal, lift the hood, disconnect the spray pipe connector, and remove the cover plate. 3. Unscrew the screws under the cover plate and take off the inner plastic panel. 4. Disconnect the motor plug, unscrew the screws on both sides of the linkage rod, and then pull it out. 5. Remove the motor from the old linkage rod and install it onto the new one. Then insert the assembly back into the rubber hole of the linkage rod, tighten the screws, reconnect the motor plug, and finally restore the seal and cover plate.
110
Share

What are the exterior dimensions of the Volkswagen Tharu?

The Tharu's body dimensions are: length 4453mm, width 1841mm, and height 1632mm. Below are additional details about the Tharu: 1. The body structure is a 5-door, 5-seat SUV. It has a wheelbase of 2680mm, a fuel tank capacity of 51L, a trunk capacity of 455L, and a curb weight of 1405kg. 2. The Tharu features a MacPherson strut front suspension and a multi-link rear suspension. It is equipped with a 1.4T turbocharged engine, delivering a maximum horsepower of 150PS, a maximum power of 110kW, and a maximum torque of 250Nm. It is paired with a 7-speed dual-clutch transmission. 3. In terms of appearance, the side profile is very clean, with a single character line running from the front fender across the body. The side of the vehicle is also adorned with protective cladding and chrome trim.
101
Share

How to Add Windshield Washer Fluid to a Geely Emgrand?

Open the driver's door of the Geely Emgrand, pull the safety latch of the engine hood, then press the hidden switch beneath the hood and slowly lift it upwards. Secure the hood with the support rod. Locate the windshield washer fluid filler inlet, typically on the left side with a small blue cap. Open the cap and pour in the prepared windshield washer fluid, then securely close the cap. More details are as follows: 1. Windshield washer fluid, commonly known as car windshield cleaning fluid, is primarily composed of water, alcohol, ethylene glycol, and various activators. 2. During nighttime driving, dust on the car's windshield can scatter light. At this time, spraying windshield washer fluid on the front windshield helps maintain optimal transparency. 3. Using windshield washer fluid provides the driver with a bright and clear field of vision. It also offers antifreeze, anti-static, and anti-corrosion properties. Based on composition, it can be divided into water and liquid windshield washer fluid.
102
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.