Can I make a U-turn at the highway toll station entrance?

1 Answers
OEvan
07/29/25 11:59pm
U-turns are not allowed in front of highway toll stations. Not only is making a U-turn prohibited on the main lanes of highways, but it is also strictly forbidden on ramps and within the toll station plaza. Making a U-turn at any section of the highway will result in a 12-point penalty. Below is relevant information about U-turns on highways: 1. For moving vehicles: Vehicles driving normally are unlikely to anticipate a car reversing, which can lead to rear-end collisions or even chain-reaction accidents. 2. Traffic regulations: Highways are designed for one-way traffic only. 3. Precautions: Making a U-turn disrupts the normal flow of traffic, endangers highway driving order, and occupies other lanes. It is advisable to plan your route in advance, memorize highway exits and junctions, and pay attention to highway signage. 4. Correct procedure: If you realize you've taken the wrong route, you should continue to the next exit to leave the highway and then return, rather than reversing or driving against traffic.
Was this review help?
7
3
Share
More Forum Discussions

What to do if the bumper has a crack?

The method to repair a cracked bumper is: 1. Prepare a set of bumper repair tools; 2. Sand the area around the bumper to remove the paint from the damaged part; 3. Use compressed air to blow away dust from the sanded area; 4. Spray plastic cleaning fluid on the sanded area to remove surface dust and impurities; 5. Cut a stainless steel repair mesh of appropriate size and fill it in the crack or hole of the bumper; 6. Use a special soldering iron to heat and initially fix the four corners of the stainless steel repair mesh on the bumper, using scissors to assist in pressing; 7. Use filler repair strips and putty for operation; 8. Use compressed air to cool it down, and after cooling, sanding and dust blowing can be performed; 9. After repeated inspection and filling of repair strips followed by sanding, you can spray paint it yourself.
4
4
Share

How many models does Wuyang Honda 125 have?

Wuyang Honda 125 motorcycles include models such as Xisha, Yusha, Kaiying, Xunsha, WH125, Fengxiang 125, Huansha, and Little Rocket. A 125 motorcycle refers to a motorcycle equipped with a 125cc displacement engine. These motorcycles come in various styles, including crossovers, scooters, and underbone bikes. The engines used in 125 motorcycles are all four-stroke gasoline engines, which operate on the same principle as car engines. A four-stroke gasoline engine goes through four strokes during operation: intake stroke, compression stroke, power stroke, and exhaust stroke. The engines in 125 motorcycles are all single-cylinder. Some motorcycles may use engines with larger displacements and multi-cylinder configurations. Wuyang Honda Motor (Guangzhou) Co., Ltd. is a Sino-Japanese joint venture invested by Guangzhou Automobile Group Co., Ltd., Honda Motor Co., Ltd. of Japan, and Honda Motor (China) Investment Co., Ltd.
6
5
Share

What engine does the Volvo V60 use?

Volvo V60 uses a 2.0T L4 turbocharged and mechanically dual-charged engine. The 2.0 refers to the engine displacement of 2.0 liters, T stands for turbocharged engine, L indicates the cylinder arrangement is inline, and 4 means the engine has a total of 4 cylinders. The space volume that the piston moves from top dead center to bottom dead center is called the cylinder displacement. Currently, common engine types include naturally aspirated engines and turbocharged engines. The Volvo V60 is positioned as a mid-size car, with all body styles being station wagons. It measures 4761mm in length, 1850mm in width, and 1432mm in height, with a wheelbase of 2872mm. In terms of power, the Volvo V60's 2.0T engine comes in two power outputs, high and low, matched with an 8-speed automatic transmission, and all models are front-wheel drive.
16
5
Share

Why doesn't the Mercedes-Benz move when started in D gear?

Mercedes-Benz not moving when started in D gear is an occasional fault issue with the parking system. For more information on engine faults, the details are as follows: 1. Pull the car over to the side: After turning off the engine for 5-10 minutes, without pressing the brake, directly press the start button, or without depressing the clutch, turn the car key halfway to the 'on' position. The car will initiate a self-check function after powering on. Wait for 5-10 seconds and observe whether the fault lights on the dashboard go out, leaving only the engine fault light. 2. If other fault lights remain on: It is necessary to go to a 4S shop or repair shop to inspect the corresponding modules and components. If only the engine fault light remains on, start the engine again and observe whether the engine fault light still remains on. If the engine fault light goes out, there is no issue. If the engine fault light remains on, it is necessary to go to a 4S shop or repair shop to inspect the engine-related components and modules.
15
0
Share

What is the timing channel number for the Volkswagen Passat?

The timing channel number for the Volkswagen Passat is 91 or 93. Relevant information about timing is as follows: Definition of Timing: The timing belt is crucial for the normal operation of the engine. Once the timing belt is damaged, the valves and ignition will stop working, and in severe cases, the cylinder head may also be damaged. As the engine operating time increases, the timing belt and its accessories, such as the timing belt tensioner pulley, timing belt tensioner, and water pump, will wear out or age. Therefore, each time the belt is replaced, these accessories should be carefully inspected to ensure they are in good condition. Precautions for Timing Usage: During use, regularly check the condition of the timing belt. If cracks are observed on the surface of the timing belt, it may indicate aging. If there are abnormal noises while driving, it is necessary to check whether the timing belt is installed correctly.
9
2
Share

Does leaving the car running with the AC on consume more fuel?

Yes, it consumes more fuel. When the car is idling without moving, it indicates the engine is in an idle state, which leads to increased fuel consumption. Here are some precautions regarding using the AC: 1. Random AC airflow direction: Adjusting the airflow direction randomly affects the interior temperature. If the AC airflow is set randomly, the cold air will cool down high-temperature components that don't need cooling, offsetting the cooling effect and reducing its efficiency. 2. Keeping the recirculation mode on for too long: Many drivers keep the recirculation mode on to save energy, which does reduce the compressor's activation frequency. However, prolonged use can make the air inside the car stale and reduce oxygen levels, leading to dizziness or even hypoxia for passengers. 3. Avoid running the AC while parked: Running the AC while the car is parked is very dangerous. When the car is idling or moving at low speeds, gasoline doesn't burn completely, producing carbon monoxide. If the AC is in fresh air mode, it will draw carbon monoxide into the car, potentially causing carbon monoxide poisoning. It's best to switch to recirculation mode.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.