Can I go to a 4S shop for maintenance after servicing outside?

2 Answers
VonConnor
07/28/25 4:48pm
You can go to a 4S shop for maintenance after servicing outside. Car maintenance items: Major maintenance items include engine oil, oil filter, air filter, and fuel filter. As for spark plugs, brake fluid, and transmission fluid, there is no fixed mileage for replacement. Major maintenance is based on minor maintenance, and in addition to engine oil and oil filter, air filter and fuel filter are also replaced. These two filters serve to filter dust from the air and impurities from the fuel. Benefits of car maintenance: Ensures driving safety, reduces vehicle fuel consumption, extends the lifespan of the car, and reduces the failure rate of car components.
Was this review help?
20
2
Share
VonHaley
08/11/25 11:26pm
Yes, you can definitely get your car serviced outside and then go to a 4S shop for maintenance. As someone who loves tinkering with cars, I think this is quite common. If you've had routine maintenance done outside, such as an oil change or filter replacement, the 4S shop usually won't refuse to service your car. The key is whether the previous maintenance was done properly and whether original or equivalent-quality parts were used. If cheap non-original parts were used, there might be compatibility issues, and the 4S shop may need to conduct additional checks during repairs to avoid potential risks. I've seen many car owners transition this way, but I recommend bringing your previous maintenance records for the 4S shop technicians to evaluate. Regular maintenance is crucial for the overall condition of your car—don’t compromise safety to save money. In short, flexibility is fine, but make sure service standards remain consistent to avoid major issues down the road.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

What type of engine oil is used for the Corolla Hybrid model?

The Corolla Hybrid uses Toyota Genuine 0W20 engine oil. Below is a detailed introduction to the engine oil for the Corolla Hybrid: 1. Engine oil is referred to as the lifeblood of the engine. Inside the engine, it not only serves as a lubricant but also performs functions such as cleaning, sealing, cushioning, rust prevention, and heat dissipation. 2. Without engine oil, the engine cannot operate properly. Over time, the performance of engine oil deteriorates in all aspects, so it is essential to change the oil on schedule. 3. When changing the oil, use a lift to raise the vehicle, then remove the oil drain plug at the oil pan to drain the old oil. 4. During an oil change, the oil filter should also be replaced. The oil filter is a crucial component used to filter the oil. Without an oil filter, the oil would become dirty after some use, which would impair its lubrication properties.
6
0
Share

How to Remove the Steering Wheel of a Fit?

Method to remove the steering wheel of a Fit: 1. Prepare a T30 screwdriver. There are two screws on the steering wheel. After unscrewing them, the airbag can be easily separated, but proceed slowly at this point because there is a connector behind it. The black horn connector can be simply pulled out. 2. For the airbag wiring, shake the white protrusions on both sides left and right to release it. The center of the steering wheel has a 10mm hex screw, which is relatively hard to unscrew and may require some effort. The steering wheel is the wheel-shaped device used to control the direction of cars, ships, airplanes, etc. Its function is to convert the force applied by the driver on the edge of the steering wheel into torque, which is then transmitted to the steering shaft. It mainly consists of a frame, foam, and the corresponding installation clips or screw holes for the driver airbag (DAB).
11
1
Share

How to turn on the air conditioning in the Trumpchi GS4?

The Trumpchi GS4 starts cooling when the A/C button is pressed. Below are detailed instructions for the Trumpchi GS4 air conditioning system: 1. The base model of the Trumpchi GS4 uses manual air conditioning, while the higher-end model features automatic air conditioning. The manual system requires adjusting the fan speed, air outlet mode, and temperature manually, which appeals to those who prefer mechanical controls. The advantage is that it doesn't require much thought, and once familiar, adjustments can be made by feel without looking down. However, the main drawback is that manual adjustments are always necessary. 2. A/C button: This is the compressor switch; pressing it activates the cooling function. FRONT button: This is the front window defroster switch; when activated, air is directed towards the windshield. REAR button: This is the rear window defroster switch; activating it heats the rear window with electric wires. 3. Using the recirculation mode: The internal air recirculation feature of the car's air conditioning is crucial, especially in areas with heavy smog and high PM2.5 levels, which can be a serious health concern. Therefore, it's important to switch to recirculation mode when driving in heavily polluted conditions. 4. In automatic mode, the fan speed, air outlet mode, and temperature are all adjusted automatically. If the temperature is set manually, all other settings adjust automatically based on the set temperature.
10
5
Share

Where is the cabin air filter located in the old Mazda 3?

The cabin air filter in the old Mazda 3 is located inside the glove compartment on the passenger side. Below are detailed instructions for the cabin air filter: 1. Remove the dashboard trim panel on the passenger side, and you will see a rectangular fuse box. Remove the fuse box, and near the driver's side, you will find the cabin air filter. 2. Steps to remove the cabin air filter: (1) There is a black plastic panel above the passenger footwell with two retractable clips. Press them to remove the panel. (2) Then disconnect the negative terminal of the battery, remove the body control module, and take off the bracket holding the body control module (two 12mm nuts). (3) Next, remove the panel on the left side of the passenger footwell, which is secured with four screws. Once removed, the disassembly is complete. Under normal circumstances, it is generally recommended to replace the cabin air filter every 10,000 kilometers or about once a year. If the vehicle is frequently driven in areas with severe air pollution, it is advisable to shorten the replacement interval. After absorbing impurities and dust for a period of time, the cabin air filter itself becomes contaminated and can no longer purify or filter effectively. Continued use may worsen pollution, leading to issues such as insufficient cooling, weak airflow from the vents, and unpleasant odors.
4
4
Share

What is the function of the car hold button?

The function of the car hold button is to adjust the optimal driving state according to different driving conditions. The hold button is a derivative function of electronic parking, which effectively prevents frequent gear shifting of the transmission on poor road surfaces and plays a role in forced downshifting during overtaking. Using this button will not cause damage to the transmission. The hold button is a measure to prevent the vehicle from rolling back during short-term parking on slopes or in traffic jams. The function needs to be activated before each use. Even in D gear, there is no need to keep pressing the brake. To release it, simply step on the accelerator, and it will automatically disengage when the driving force exceeds the resistance, so there is no need to shift the gear to neutral. For long-term parking, it is best to shift the gear to neutral or P gear and engage the handbrake system.
16
2
Share

How to Turn Off the Rear Wiper on a Volkswagen?

Method to turn off the rear wiper on a Volkswagen: Simply push the wiper lever forward to deactivate it. The windshield wiper is a device used to wipe away raindrops and dust attached to the vehicle's windshield, thereby improving the driver's visibility and enhancing driving safety. Due to legal requirements, almost all vehicles worldwide are equipped with wipers, including rear windows of hatchbacks and SUVs. The wiper assembly consists of components such as an electric motor, reducer, four-bar linkage, wiper arm spindle, and wiper blade assembly. When the driver activates the wiper switch, the motor starts, and its rotational speed is converted into increased torque through a worm gear mechanism, driving the swing arm. The swing arm then moves the four-bar linkage, which causes the shaft mounted on the front panel to oscillate left and right, ultimately driving the wiper blade to sweep across the windshield.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.