Can I Apply for an A3 Driver's License on My First Attempt?

1 Answers
DelBrody
07/29/25 2:06am
You can apply for an A3 driver's license on your first attempt. The A3 driver's license is a qualification for driving buses, and it is the only A-class license that can be applied for during the initial driver's license application. Additionally, you can also obtain an A3 driver's license through license upgrading. Requirements for applying for an A3 driver's license: Age between 21 and 50 years old; height of at least 155 cm; naked or corrected vision of 5.0 or above, with no red-green color blindness; ability to distinguish the direction of sound with both ears; both thumbs must be intact, and each hand must have three intact fingers with normal movement; normal movement of the torso and neck, normal movement of the lower limbs, and a length difference between the two lower limbs not exceeding 5 cm. Vehicles allowed with an A3 license: Although the A3 license is for driving buses, it is not limited to buses. According to relevant regulations, holders of an A3 license can also drive vehicles permitted under the C1 license, such as small cars, small automatic transmission cars, low-speed trucks, and three-wheeled vehicles.
Was this review help?
12
5
Share
More Forum Discussions

What is power steering oil?

Power steering oil is a special fluid used in the car's power steering pump. Through hydraulic action, it can make the steering wheel lighter, similar to automatic transmission fluid, brake fluid, and shock absorber fluid. To prevent the power steering oil from becoming dirty or deteriorating, it should be replaced every 2 years or 30,000 kilometers. Precautions for using power steering oil include: 1. Power steering oil contains carcinogenic substances; if it comes into contact with the skin, it should be washed off immediately. 2. For cars equipped with hydraulic power steering systems, avoid holding the steering wheel at full lock for extended periods, as this can burn out the power steering pump over time.
4
1
Share

What are the reasons for the failure of car auto-locking?

Car auto-locking failure is caused by poor wire contact or door lock damage, and it may also be a program malfunction issue, requiring inspection and repair at a service center. The purpose of the auto-locking function is theft prevention, allowing the doors to lock quickly after driving to prevent door-pull robberies during traffic jams or at red lights, providing a certain level of security. The car auto-locking function, also known as speed-sensing auto-lock, is an electronic device that automatically presses the lock button on the door when the vehicle speed reaches a computer-set value, preventing accidental door opening. The set value is generally factory-set, usually between 10 to 20 kilometers per hour.
20
1
Share

How to Set the Headlight Delay Shut-off?

To set the headlight delay shut-off: 1. Tap into Settings on the central control screen, then select Lights; 2. In the light settings interface, locate the headlight delay shut-off option and configure it directly. The headlight delay shut-off is essentially a function that keeps the headlights on for a period after the vehicle is turned off, providing external illumination for the driver after exiting the vehicle. The headlight delay shut-off feature in the Jeep Cherokee can supply up to 90 seconds of safety lighting when the car is in dimly lit areas. To activate the delay function, turn the ignition switch to the OFF position while the headlights are still on, then turn off the headlights within 45 seconds.
14
0
Share

What Causes a Dead Battery in the Baojun 560?

A dead battery in the Baojun 560 will result in the inability to start the vehicle or ignite the engine. Below are the charging methods: 1. You can jump-start the vehicle using another car, tow it to a repair shop for charging, or use a portable charger to charge the battery on-site. 2. After connecting the charger to the positive and negative terminals of the battery, set the charging parameters to begin charging. Normal charging time is around 20 hours. For a faster charge, you can double the charging current, which typically takes 6-8 hours. 3. When charging the battery while it is still installed in the car, avoid starting the engine midway, as this may damage the central control electronic devices.
4
0
Share

How to replace the low beam light of BYD F3?

The method to replace the low beam light of BYD F3 is: 1. Open the engine hood release lever from the driver's compartment, reach into the opened engine hood, and lift the engine hood; 2. After opening the engine hood, disconnect the nearby power connector; 3. Use a small wrench to grip the raised part of the lamp rear cover and rotate it clockwise to open the rear cover; 4. Press down firmly on the fixing bracket, lift the bracket upwards, and then the bulb can be removed and replaced with a new one. Taking the 2020 BYD F3 1.5L Manual Classic as an example: The manufacturer of this car is BYD, its class is compact car, and the energy type is gasoline.
5
1
Share

How to Check the Production Date of an Engine?

To check the production date of an engine, you can use the following methods: 1. Look for the nameplate in the engine compartment, which is located inside the engine bay. It displays the vehicle's serial number, engine displacement, model, brand, and importantly, the specific production date. 2. Check the small nameplate around the door seams, typically found near the driver's or passenger's door. 3. Locate the vehicle identification number (VIN) under the front windshield. The car engine is the device that provides power to the vehicle, acting as the heart of the car, determining its power, fuel efficiency, stability, and environmental friendliness. Depending on the power source, car engines can be categorized into diesel engines, gasoline engines, electric vehicle motors, and hybrid engines.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.