Can Getting a Driver's License Be Used as a Reason for Leave?

1 Answers
DelCaroline
07/25/25 1:23am
Getting a driver's license can be used as a reason for leave. You can say that it is for the convenience of work, so taking leave to get a driver's license makes it easier to request. It might not even be counted as leave, especially if driving is required for the current job. It depends on the position. Those who frequently travel for work are more likely to have their request approved, while those who rarely travel may not have this reason accepted, and it might be considered personal leave. Below is an introduction to the driver's license process: 1. Subject 1: Study and examination, usually takes about 2 weeks. 2. Subject 2: Study and examination, including pile training and pile test, field training and field test, ideally taking about 3 weeks. 3. Subject 3: Study and examination, road training and road test, ideally taking about 3 weeks. In total, it takes about 8 weeks, roughly 2 months.
Was this review help?
2
4
Share
More Forum Discussions

What does Honda Oillife mean?

Honda Oillife indicates the remaining life of the engine oil. Below are the specific steps for changing the engine oil: 1. Warm up the car before changing the oil: Start the vehicle and let the engine reach normal operating temperature, then turn off the engine. The purpose of warming up the car is to allow the oil to flow fully and carry out impurities. Use a jack to lift the vehicle and engage the handbrake. 2. Drain the old oil: Use the vehicle's tools to loosen the oil drain plug at the oil pan and drain the oil. Be sure to collect the old oil in a container to avoid environmental pollution. Once the oil is completely drained, reinstall the drain plug, being careful not to overtighten it to prevent damage to the oil pan. 3. Install the new oil filter: Use an oil filter wrench to loosen the old filter. Apply new oil to the oil seal of the new filter, then manually install the new oil filter and tighten it with the tool. 4. Add new oil: Pour the new oil into the oil filler port, using a funnel if necessary. After adding the oil, check for any leaks. If there are no abnormalities, remove the jack and lower the vehicle. Use the dipstick to confirm the oil level, then restart the vehicle and check if any warning lights are illuminated.
12
4
Share

How many brake lights does the Tiida have?

The Tiida has 3 brake lights, which are installed at the rear of the vehicle. These lights feature a red main body color to enhance light penetration, making it easier for following vehicles to detect braking even in low visibility conditions, thereby helping to prevent rear-end collisions. The Tiida's body dimensions are: length 4393mm, width 1766mm, height 1539mm, with a wheelbase of 2700mm and a fuel tank capacity of 50 liters. The Tiida is equipped with a 1.6L naturally aspirated engine, delivering a maximum power of 90kW and maximum torque of 155Nm, paired with a 5-speed manual transmission.
17
1
Share

How to Solve the Issue of the Fuel Tank Not Filling Completely and the Pump Nozzle Clicking Off?

To solve the issue of the fuel tank not filling completely and the pump nozzle clicking off: 1. Check if the fuel gauge is functioning normally; 2. Ensure the pump nozzle is inserted deeply into the fuel tank opening when refueling. The reasons for the fuel tank not filling completely and the pump nozzle clicking off include: 1. Rapid refueling can generate expanding vapor, and the gas displaced by the fuel doesn't have time to release; 2. Issues with the fuel gauge or the pump nozzle not being inserted deeply enough. The effects of overfilling the fuel tank until the nozzle clicks off are: 1. Difficulty starting the engine and unstable idling; 2. A noticeable gasoline smell inside the car; 3. Failure of the carbon canister; 4. Potential fire hazards. The fuel tank is a container that stores fuel in a vehicle, serving as the storage location for fuel in gasoline-powered cars and the power source for the engine.
9
3
Share

How to upgrade the navigation system in BYD S7?

The method to upgrade the navigation system in BYD S7 is: 1. Open the navigation website URL to download the navigation upgrade file; 2. Eject the original navigation card from the car, insert it into the computer using a card reader, decompress the downloaded file, and then double-click to run; 3. The installation software will automatically recognize the inserted storage card; 4. After clicking to install successfully, proceed with debugging. The body dimensions of BYD S7 are: length 4835mm, width 1855mm, height 1720mm, with a wheelbase of 2730mm. BYD S7 is equipped with a 1.5T turbocharged engine, with a maximum power of 113kW and a maximum torque of 240Nm, paired with a 6-speed manual transmission.
13
0
Share

What is the safe following distance when driving?

The safe following distance when driving varies according to speed: 1. When driving at a crawling speed (below 20 km/h), the safe distance should be no less than 10 meters; 2. When driving at low speed (below 40 km/h), the safe distance should be no less than 30 meters; 3. When driving at medium speed (around 50 km/h), the safe distance should be no less than 50 meters; 4. When driving at high speed (above 60 km/h), the safe distance should be 60 meters; 5. When driving on highways (above 100 km/h), the safe distance should be no less than 100 meters.
4
4
Share

How Long Does It Take to Apply Car Window Tint?

Car window tinting time varies depending on the vehicle model: 1. Medium-sized sedans take approximately 3 to 4 hours; 2. Larger vehicles take about 4 to 4.5 hours; 3. MPVs (Multi-Purpose Vehicles) take around 5 hours. Post-tinting precautions include: 1. Avoid directing air conditioning vents toward the tint to prevent rapid thermal expansion and contraction; 2. Do not clean the tint or activate the defroster switch for one week after application; 3. Avoid using solutions containing alcohol or ammonia to clean the tint surface; 4. Before tinting, check the window glass installation for completeness and the overall integrity of the car glass; 5. Clean the inner and outer surfaces of the windows before tinting; 6. Avoid rolling windows up or down for 3 days after tinting.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.