Can a vehicle pass the inspection if the high-mounted stop lamp is not working?

1 Answers
AubreyRose
07/29/25 10:33pm
High-mounted stop lamp not working will cause the vehicle to fail the inspection. The high-mounted stop lamp is a light that illuminates when the vehicle brakes, serving to alert drivers behind to maintain a safe distance and avoid rear-end collisions. Types of vehicle stop lights are categorized as follows: 1. By position: rear stop lights, dashboard stop lights, and high-mounted stop lights; 2. By material: gas stop lights and LED stop lights. Causes of stop light failure include: 1. Damaged stop light fuse; 2. Faulty stop light switch.
Was this review help?
7
3
Share
More Forum Discussions

What is the general idle speed of a car?

Car idle speed varies between cold and warm engine conditions. When the engine is warm, the idle speed ranges from 550 to 800 RPM, while in cold conditions, it ranges from 950 to 1300 RPM. Once the engine temperature rises to a certain level, the idle speed will decrease to the normal range. Idle refers to the state when the engine is running without any load, which occurs when the accelerator pedal is fully released during engine operation. Idle speed is one of the engine operating conditions, so its performance significantly impacts emissions, fuel consumption, and comfort. The engine speed during idle is called idle speed, which should not be too high or too low. Excessively high idle speed increases fuel consumption, while excessively low idle speed causes unstable engine operation.
13
2
Share

How to Remove the Fuel Pump on a Beidou Star?

First, prepare the necessary tools for removing the fuel pump, then position the vehicle on a level indoor surface with the ignition switch in the OFF position; engage the parking brake. Use tools to slowly remove the rear inspection hole cover (gently pry it up without using excessive force, as there are wiring harnesses underneath). Disconnect the cable from the negative terminal of the battery, and remember to wrap the disconnected fuel pipe with plastic wrap to prevent dirt from entering. Also, note the original installation position. Clean the upper part and edges of the fuel pump assembly (there may be a lot of dirt, which can be wiped clean with a cloth). Using a screwdriver wrapped with protective tape, remove the No. 1 fuel suction pipe bracket, then carefully take out the fuel pump from below. Press the lower locking clip by hand to remove the O-ring of the fuel pump.
3
4
Share

What causes the gear failure in Focus?

Focus gear failure is likely caused by gear lock or not fully braking when parking, directly shifting into P gear, resulting in gear braking instead of brake braking. Solutions: If the entire vehicle cannot power on and the automatic transmission enters self-protection mode, it may also fail to engage gears. Gear unlocking can be performed. If it still doesn't work, you should go to a professional 4S store for inspection by professional maintenance personnel. Smart configurations: The Ford Focus is equipped with the SYNC+ intelligent information entertainment system, which has natural semantic recognition capabilities, supports multi-scenario wake-free operation, and mixed Chinese-English commands. It can use voice to control four major functions: entertainment, intelligent navigation, communication, and vehicle temperature. Additionally, the in-car LCD instrument panel has been upgraded to 8 inches, and the central control screen has been upgraded to 12.3 inches.
17
3
Share

What are the interior buttons of the 2020 Geely Vision X6?

Geely Vision X6 integrates multifunction buttons at the three and nine o'clock positions on the steering wheel, which can control cruise control, voice control, Bluetooth calls, and other functions. The buttons have a solid texture and offer decent pressing feedback. Configuration of the Geely Vision X6: The new Vision X6 features a panoramic sunroof and a 1850L trunk. It is equipped with Geely's new 1.4T engine, with fuel consumption as low as 6.2L/100km. Performance of the Geely Vision X6: The new Vision X6 leads its class in power performance. The second-generation 1.4T engine is highly efficient and energy-saving, meeting the China VI emission standards across all models. It comes with two transmission options: 8CVT and 6MT, delivering both power and
1
1
Share

What is the remote control matching method for BYD F3?

BYD F3 remote control matching operation method is as follows: 1. Open the driver's door, sit inside, and close the door. 2. Insert the original car key without turning it, then open the driver's door. 3. Turn the key from OFF position to ACC position, then to ON position, back to ACC position, and then to ON position again. This step must be completed within 15 seconds. 4. Close and then open the driver's door. 5. Turn the ignition key from ON position to ACC position, then to ON position. At this point, the alarm horn will sound once. Immediately press the middle button of the new remote control for 2 seconds, or repeatedly press the middle button. If the alarm horn sounds twice, it indicates successful matching. If it sounds four times, it indicates matching failure.
19
1
Share

Are There Charging Piles on National Highways?

Nowadays, many national and provincial highways have driver service areas with parking spaces, restrooms, and lounges, and some even have scenic viewpoints. In such locations, 4-8 charging piles are typically installed. Introduction to Charging Pile Appearance: Charging piles function similarly to fuel dispensers at gas stations. They can be fixed to the ground or walls and are installed in public buildings (such as office buildings, shopping malls, public parking lots) as well as residential parking areas or charging stations. They can charge various types of electric vehicles at different voltage levels. Introduction to Charging Pile Functions: For an electric vehicle, the battery charging system is one of the essential subsystems. Its function is to convert grid electricity into the energy stored in the vehicle's battery. Electric vehicle charging devices can be classified in different ways, but broadly, they fall into two categories: onboard charging devices and off-board charging devices.
1
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.