Can a tube be inserted into the New Santana's fuel tank?

1 Answers
Colton
07/25/25 3:51am
New Santana's fuel tank can have a tube inserted. To do this, disconnect the return fuel pipe at the front of the New Santana's fuel tank, guide the tube into a bucket, start the car, and the fuel pump will pump out the fuel. New Santana fuel tank capacity: The volume is 55 liters. Santana design advantages: The biggest highlight is the all-new EA211 series naturally aspirated engine, featuring an aluminum cylinder block and an improved camshaft valve train. The 1.6L model has a MIIT combined fuel consumption of 5.9 liters per 100 kilometers, meaning a Santana can travel approximately 900 kilometers on a full tank. The New Santana completely abandons the old boxy design in favor of a dynamic appearance, adopting the latest overall styling. The chrome trim below the windows is simple yet aligns with Chinese consumers' aesthetic preferences, and it still uses large drum brakes.
Was this review help?
3
1
Share
More Forum Discussions

Does the Levin have L2 autonomous driving?

The Levin is equipped with L2-level autonomous driving technology, but it is only available in the high-end models. Here is more information about the Levin: 1. The vehicle's length is 4640 mm, width is 1780 mm, height is 1435 mm, wheelbase is 2700 mm, front track is 1531 mm, and rear track is 1535 mm. 2. This vehicle is a four-door, five-seat sedan with a fuel tank capacity of 50 liters and a trunk capacity of 471 liters. It is positioned as a compact car and is produced by GAC Toyota. 3. The vehicle uses three types of engines: a 1.2T turbocharged engine, a 1.5L naturally aspirated engine, and a 1.8L naturally aspirated engine, paired with a CVT 10-speed transmission. The energy type of the vehicle is gasoline and hybrid.
13
4
Share

What Causes the Engine Warning Light to Illuminate in Golf 6?

The engine warning light in a Golf may illuminate due to the following 7 main reasons: Sensor Failure: The sensors involved include those for coolant temperature, crankshaft position, air flow, intake temperature, oxygen, etc. When these sensors are damaged, have poor contact, or their signals are interrupted, the vehicle's ECU cannot accurately obtain engine data, leading to the illumination of the engine warning light. Fuel or Oil Quality Issues: Failure to use the fuel or engine oil as specified by the manufacturer may cause engine wear, triggering the warning light. Poor Combustion of Air-Fuel Mixture: Poor combustion can lead to engine carbon buildup or knocking. Once detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as a warning. Spark plug failure, ignition coil failure, fuel pump failure, or fuel line blockage can all cause poor combustion of the air-fuel mixture. Turbocharger Issues: The intake boost pipe or turbocharger can also cause the engine warning light to illuminate. The most common issue is turbocharger damage, accompanied by symptoms such as oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake Problems: Issues with the car's intake system can lead to engine pipe blockages, and in severe cases, cause the engine warning light to illuminate. A dirty or uncleaned air filter can result in intake problems. Exhaust Problems: Exhaust system failures can also trigger the engine warning light. Common causes include rear oxygen sensor failure, catalytic converter issues, or faults in the exhaust camshaft and bearings, with the catalytic converter being the most frequent culprit. Using leaded gasoline, lead or silicon-containing lubricant additives, physical damage to the catalytic converter, or fuel system failures can easily lead to catalytic converter problems. Anti-Theft System Fault: If the car's electronic anti-theft system malfunctions or if there's a mismatch between the anti-theft controller and the engine ECU, the anti-theft system can prevent the engine from operating normally, accompanied by the illumination of the engine warning light. If the engine warning light illuminates, follow these steps: First, check if the engine is running normally, looking for signs of shaking, black smoke, etc. If such symptoms are present, avoid restarting the engine. Note: Do not restart the engine if the warning light is red. If the engine can be started, turn it off and wait for 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the 'on' position without depressing the clutch. The car will perform a self-check upon powering up. Wait for 5-10 seconds to see if the warning light turns off. If the warning light remains on, visit a service station as soon as possible. The service station can use a portable diagnostic tool to read the fault codes, identify the issue, and perform targeted repairs.
10
5
Share

How to Use Lexus Cruise Control?

Lexus cruise control is used as follows: 1. Press the control switch to activate cruise control standby. The cruise control lever is located near the steering wheel. After accelerating to the desired speed, push the lever downward to set the cruising speed. 2. Cruise control allows the driver to automatically maintain the set speed without pressing the accelerator pedal. 3. Especially during long-distance driving on highways, it can reduce driver fatigue and minimize unnecessary speed changes, thereby achieving fuel savings. Below are some relevant points about cruise control: 1. Be mindful of the speed difference between the current speed and the set speed. A large gap between the current speed and the set speed when activating cruise control can cause sudden acceleration, which not only increases fuel consumption but also poses safety risks. 2. For example, if you set the target speed to 120km/h on the highway, but your speed is not very high when exiting a toll booth, do not immediately activate the cruise control system, as this could potentially lead to a rear-end collision or loss of vehicle control.
2
5
Share

What brand does the Lynk & Co 01 belong to?

Lynk & Co 01 is the first model of the Lynk & Co brand, a joint venture established by Geely Auto Group, Geely Holding Group, and Volvo Cars, primarily producing sedans and SUVs. Here is more information about Lynk & Co: 1. Lynk & Co models feature internet and global DNA, positioned as compact SUVs built on the CMA platform, all equipped with a 2.0T turbocharged engine incorporating Volvo technology. 2. The Lynk & Co 01 has a body length, width, and height of 4549mm, 1860mm, and 1689mm respectively, with a wheelbase of 2734mm, a minimum ground clearance of 213mm, and uses an 8-speed automatic transmission (AT).
3
4
Share

Where is the Lexus TRC switch located?

Lexus's TRC activation button is located on the left side of the vehicle's gear shift, with a vehicle anti-skid symbol on the button. The TRC function refers to the vehicle's active traction control system, which prevents the car from spinning on slippery surfaces such as snow, making the vehicle's start and acceleration smoother. Here is some information about the traction control system: 1. The mechanical structure of the TRC active traction control system prevents the drive wheels from spinning when the vehicle is driving on slippery surfaces such as snow, allowing the vehicle to start and accelerate smoothly, supporting the basic functions of vehicle operation. 2. The traction control system, known as Traction-Control-System (TCS), is also referred to as ASR or TRC. 3. Its function is to enable the car to obtain optimal traction under various driving conditions.
14
5
Share

How to adjust the audio system in Mercedes-Benz E300?

The audio system in Mercedes-Benz E300 can be adjusted in the following two ways: 1. Increase both treble and bass to +6, set midrange to zero, and adjust the overall sound field by moving it towards the rear seats to -3 or -4. 2. Set the bass to the highest level, adjust midrange to 4/5, and treble according to personal preference (recommended at 2/3). For speaker position adjustment, set the left-right balance of the auditory center to 0 and the front-rear balance to -5. This maximizes the use of the front bass speaker volume. Below are some recommended audio settings for Mercedes-Benz E300: 1. For vocal music, set treble to 70% and bass to 50%. 2. For rock music, set treble to 70% and bass to 50%. 3. For DJ or slow rock music, set treble to 40% and bass to 70%. 4. For pop music, set treble to 60% and bass to 70%. 5. For styles like Black Duck or Tong Li, set treble to 75% and bass to 70%.
6
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.