Can a new electric car be charged when there are 2 bars of battery left?

1 Answers
SanMaci
07/24/25 1:34pm
Yes. Here is the extended content: The first charge for a new electric car battery should last 10 to 14 hours. Normally, the battery should be charged when the remaining power is below 30%. Therefore, when the battery display shows two bars remaining, it can be charged for daily use of the electric car. Precautions: Avoid over-discharging the battery. When the battery is depleted, the internal separator is prone to damage, which will shorten its lifespan. When the electric car is not used for a long time, the battery will also experience internal leakage and power loss. The battery should be fully charged before storage, and then fully charged every 20 days to a month to prevent damage.
Was this review help?
13
5
Share
More Forum Discussions

What transmission does the Song PLUS use?

Song PLUS is equipped with the latest 7-speed wet dual-clutch transmission, which has been specially optimized for the usage habits and scenarios of Chinese users. It features certain technical upgrades in terms of transmission smoothness, fuel efficiency, and durability. Introduction to Dual-Clutch Transmission: A dual-clutch transmission is a product developed based on a manual transmission. Its structure is similar to that of a manual transmission, but it adds an extra set of clutches and shift control mechanisms. One clutch controls the odd-numbered gears, while the other controls the even-numbered gears. Advantages of Dual-Clutch Transmission: It is based on a manual transmission but is not an automatic transmission. Besides offering the flexibility of a manual transmission and the comfort of an automatic transmission, it also provides uninterrupted power output.
12
0
Share

What Causes Engine Noise During Cold Start in Geely Vision?

Reasons for engine noise during cold start in Geely Vision: Poor oil lubrication: After the car has been parked for a day, the engine lubricant basically all flows back to the oil pan. During a cold engine start, the oil pump cannot immediately establish oil pressure and form an oil film between components. Especially the valves inside the cylinder head do not receive lubrication during cold starts. Whether it's hydraulic lifters or mechanical rocker arms, there will be some valve clearance, resulting in abnormal noise. Carbon canister solenoid valve noise: The function of the carbon canister solenoid valve is to open the electromagnetic valve installed between the carbon canister and the intake manifold after the engine starts. This not only reduces emissions but also lowers fuel consumption. However, abnormal noise may occur during its operation.
3
3
Share

What are the causes of power steering failure in the MG GS?

MG GS power steering failure causes: Power steering pump failure: Lack of oil, obstructed oil circuit, air in the oil circuit. Pressure relief, solenoid valve not energized: Torque sensor failure and other forms of power assistance failure. Poor connector contact: Poor contact in the control system wiring harness connector, blown fuse, system fuse blown, relay damage, controller, motor or sensor failure affecting the electric power steering system. Power steering troubleshooting methods are as follows: Correct selection of hydraulic oil: Choosing the right hydraulic oil is key to ensuring the pump's efficiency and extending its lifespan. Regularly check the oil reservoir: Regularly inspect the oil level in the reservoir and replenish with clean hydraulic oil if insufficient. The filter element in the reservoir should be cleaned with alcohol during maintenance.
9
0
Share

Where is the USB port located in the Geely New Emgrand?

The USB port in the Geely New Emgrand is located near the cup holder in the center armrest area. There is a dust-proof cover that can be opened to reveal the USB and HDMI sockets. Note that only the mid-range and high-end configurations of the Emgrand come equipped with USB ports. These ports utilize the vehicle's standard power supply to charge DC 5V electrical devices via USB or serve as fixed power interfaces for electronic devices. The New Emgrand is a sub-brand under Geely's parent brand, with body dimensions of 4632mm in length, 1789mm in width, and 1470mm in height, and a wheelbase of 2650mm. It is powered by a 1.3T GeTec DVVT turbocharged engine, features front-wheel drive, and delivers a maximum power output of 98kW.
16
1
Share

Why is there no sound from the rear speakers of the Haval H6?

The reason why there is no sound from the rear speakers of the Haval H6 may be that it is in mute mode or the volume is turned down, making it inaudible. Next, turn on the radio to play and determine whether the speaker is malfunctioning. Introduction to car audio: Car audio refers to the sound system installed in the vehicle. The system can be called an audio system because its most basic function is to reproduce sound. Its anti-interference technology involves using a choke coil connected between the power supply and the audio system to filter interference from the power line, thereby reducing external noise interference. Components of car audio: Head unit, which is the audio source of the car; speakers, the sound-producing units of the car audio system, converting electrical energy into sound waves; amplifier, commonly known as a "power amplifier," is the most basic device in the audio system.
15
2
Share

Should You Press the Clutch When Turning with a Manual Transmission?

When driving a manual transmission car, you should not press the clutch while turning. The specific reasons are as follows: Risk of losing control: Beginners driving manual transmission vehicles often release the accelerator, press the clutch, and brake to reduce speed when entering a turn. While this operation may seem correct, it actually carries significant risks, ranging from minor skidding to complete loss of vehicle control. Pressing the clutch only cuts off the power, but the car still has momentum. Once the wheels lose traction, the vehicle becomes more prone to losing control. Correct method for taking turns: Reduce speed and downshift before entering the turn. Use the brakes to control speed while turning, maintain the gear during the turn, and directly press the accelerator to upshift after completing the turn.
8
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.