Can a Car Run Normally Without the Generator Producing Electricity?

1 Answers
AniyahRose
07/29/25 5:07pm
If the generator does not produce electricity, the car cannot run normally. The generator in a car is a crucial component. A synchronous generator operates based on the principle of electromagnetic induction, converting mechanical energy into electrical energy through the relative motion between the rotor's magnetic field and the stator windings. Below is an introduction to car generators: 1. Car Generator: The car generator is the main power source of the vehicle. Its function is to supply power to all electrical devices (except the starter) while the engine is running normally and simultaneously charge the battery. 2. Working Principle: When an external circuit energizes the excitation winding through the brushes, it generates a magnetic field, magnetizing the claw poles into N and S poles. As the rotor rotates, the magnetic flux alternates in the stator windings. According to the principle of electromagnetic induction, an alternating electromotive force is induced in the three-phase windings of the stator. This is the power generation principle of an alternator.
Was this review help?
5
2
Share
More Forum Discussions

Is 18650 a Lithium Battery?

18650 is the pioneer of lithium-ion batteries. Here is the relevant introduction about 18650: 1. It is a standard lithium-ion battery model set by Sony Corporation of Japan to save costs at that time. Among them, 18 represents a diameter of 18mm, 65 represents a length of 65mm, and 0 represents a cylindrical battery. 2. Common 18650 batteries are divided into lithium-ion batteries and lithium iron phosphate batteries. The voltage of lithium-ion batteries is 3.7v, the charging cut-off voltage is 4.2v, the nominal voltage of lithium iron phosphate batteries is 3.2V, the discharge cut-off voltage is 3.6v, and the capacity is usually 1200mAh-3350mAh, with the common capacity being 2200mAh-2600mAh.
10
1
Share

How to reset the maintenance light on Changan Suzuki?

Changan Suzuki's maintenance light reset procedure consists of four steps: 1. Turn on the ignition switch and briefly press the right-side information display selector handle. 2. Press and hold the left-side odometer button for more than 5 seconds until the oil lock indicator appears on the display, then release the button. The display area will show the oil lock. 3. After completing step two, release the button and press it five times consecutively within 2 seconds. This operation must be completed within 3 seconds. 4. The "oil lock" will turn off, and "SUCCESSFUL" will be displayed, indicating the reset operation is complete. The purpose of car maintenance is to keep the vehicle clean and tidy, maintain normal technical conditions, eliminate potential hazards, prevent faults, slow down the deterioration process, and extend the service life.
16
2
Share

How many kilometers should brake pads be replaced?

Generally speaking, the replacement interval for front brake pads is 30,000 kilometers, while rear brake pads should be replaced every 60,000 kilometers. Here is some relevant information about brake pads: 1. Brake pads, also known as brake linings, are the most critical safety components in a car's braking system. The effectiveness of all braking performance is decisively determined by the brake pads, making high-quality brake pads the guardian of both people and vehicles. 2. The main difference between ceramic brake pads and traditional brake pads is the absence of metal. In traditional brake pads, metal is the primary material that generates friction, providing strong braking force but with greater wear and a tendency to produce noise. After installing ceramic brake pads, no abnormal screeching (i.e., scraping sounds) will occur during normal driving. Since ceramic brake pads do not contain metal components, they avoid the metal screeching noise caused by the friction between traditional metal brake pads and their counterparts (i.e., brake pads and brake discs).
15
5
Share

What Causes the Dashboard Brake Light Not to Illuminate?

There are many reasons why the dashboard lights of a car may not illuminate, including a blown fuse in the dashboard, a dead car battery, excessively bright external lighting, or the lights not being turned on. The specific explanations are as follows: 1. Blown fuse in the dashboard: If the dashboard fuse blows, it will not only cause the dashboard lights to not illuminate but also prevent the dashboard needles from moving. In this case, a new fuse needs to be replaced to avoid unnecessary trouble caused by the dashboard not functioning properly. 2. Dead car battery: Insufficient power can also cause the dashboard lights to not illuminate. 3. Turning the light control knob one notch can make the dashboard lights come on. This car has light-sensitive dashboard lights; when the surrounding environment is dark and the lights need to be turned on, the dashboard lights dim to remind the driver to turn on the headlights promptly (while the dashboard lights also illuminate).
6
3
Share

What to Do When the ABS Light Comes On and the Car Won't Lock in a Baojun?

Baojun ABS faults can be checked based on the following aspects: 1. Conduct a visual inspection of the system to check for damaged wires, loose plugs, and low brake fluid levels. 2. Use a decoder to read and interpret fault codes to identify the fault conditions represented by the codes. 3. Based on the interpreted fault conditions, use necessary tools and instruments to conduct an in-depth inspection of the faulty parts to diagnose the fault location and cause. 4. If the warning light remains on, there may still be a fault in the system, or the fault may have been resolved but the fault code has not been cleared. Below is an introduction to the reasons why the ABS light comes on: 1. Issues with the ABS wheel speed sensor. The wheel speed sensor is located on the wheel and is easily contaminated by dirt or mud. If the sensor is covered with a large amount of dirt, it can affect the transmission of the speed signal. The ABS computer cannot determine the speed signal and will trigger an alarm. In this case, cleaning the dirt on the sensor and adjusting the gap between the sensor and the signal ring can resolve the issue. If the wheel speed sensor is damaged, it must be replaced. 2. Line connection faults, which are relatively common. Although all cars have ABS systems, the assembly quality and materials may vary due to different manufacturing processes. Loose connections in the wheel speed sensor wiring are quite common and should be checked thoroughly. Line troubleshooting can be tedious, so patience is required. It's best to inspect each plug, including the contact condition of related fuses and the grounding of the ground wire. 3. Issues with ABS control unit programming, likely due to mismatched or incorrect data within the control unit. The data needs to be readjusted, which requires a specialized diagnostic computer. 4. Problems with the ABS master cylinder. 5. Faults in the ABS control unit circuit board, requiring replacement of the computer. However, this type of fault is very rare.
6
4
Share

What is the best mileage interval for replacing Focus spark plugs?

There are four points to determine whether Focus spark plugs need to be replaced based on mileage: 1. Copper core should be replaced every 20,000-30,000 kilometers. 2. Nickel alloy core should be replaced every 40,000-60,000 kilometers. 3. Platinum core should be replaced every 80,000 kilometers. 4. Iridium core should be replaced every 100,000 kilometers. The following is an introduction to the structure of spark plugs: 1. Steel shell: The lower part of the steel shell has fine threads for installation in the cylinder head spark plug hole, and the upper part has an external hexagonal nut for installing a spark plug socket to tighten or loosen the spark plug. 2. The metal rod is the center electrode. The lower end of the metal rod contacts the upper end of the center electrode through conductive glass, and the upper end of the metal rod is equipped with a terminal nut. 3. There is high-alumina ceramic insulation between the steel shell and the center electrode to insulate the center electrode when energized. 4. The lowest part of the steel shell is equipped with a curved side electrode. 5. The middle part of the steel shell has a copper gasket.
6
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.