Can a Car in the Break-in Period Drive on the Highway?

1 Answers
StElaina
07/25/25 3:10am
It is possible for a car to drive on the highway during the break-in period, but it is recommended to keep the speed below 100 kilometers per hour and the engine RPM below 2,500. Here is more information about the car break-in period: 1. The break-in period generally refers to the initial operation process where mechanical components come into contact, rub, and mesh. During this period, it is essential to control the driving speed. 2. Taking the car on the highway during the break-in period not only tests its performance at high speeds but also helps clear engine carbon deposits caused by low-speed driving. Maintaining a speed of 100 kilometers per hour on the highway for about two hours is advisable, followed by a proper rest. Once the car has covered over 3,000 kilometers during the break-in period, it will reach an optimal condition.
Was this review help?
4
2
Share
More Forum Discussions

Where are the accelerator and brake pedals located in a Volkswagen car?

In a manual transmission car, from left to right, the pedals are the clutch, brake, and accelerator. The manual transmission cabin has three pedals, while the automatic transmission cabin has two pedals. During driving, the left foot should not be placed on the brake pedal. For manual transmission models, the left foot should only be used to press the clutch pedal when shifting gears. Normally, the left foot should not be placed on any pedal. Both the brake and accelerator are controlled by the right foot. There are two main reasons why the left foot should not be placed on the pedals: 1. During long drives, both feet can become very tired and may unconsciously press down. If the left foot is on the brake pedal at this time, pressing it could easily cause an accident or danger. 2. Most people are right-handed, so the right foot reacts faster. In case of an emergency, the right foot can react quickly to lift off the accelerator and press the brake pedal. If the left foot is on the brake pedal, the right foot would be suspended when braking, making it easy for both feet to press down simultaneously, leading to danger. Additional information about car brakes and accelerators: The brake is a mechanical braking device that slows down the vehicle, also known as a decelerator. The car's brake pedal is located below the steering wheel. Pressing the brake pedal activates the brake linkage, which presses the brake pads against the brake rotor, slowing or stopping the car. The accelerator is a device that controls the fuel supply in an internal combustion engine. In cars, the accelerator is usually controlled by a pedal, also known as the throttle pedal, which regulates the fuel supply to the engine. When pressing the brake or accelerator, the body needs support to maintain balance. When the right foot presses the pedal, the left foot can stabilize the body on the floor. If both feet are placed on the brake and accelerator, they would both be semi-suspended, lacking a stable point of support, which could lead to unstable pressing of the pedals. Tips for new drivers: 1. Signal early when changing lanes or turning: Lights and horns are the language of driving. Always communicate your intentions, especially as a new driver. Signal early to ensure safety. When changing lanes or turning, develop the habit of using turn signals and avoid immediately changing lanes or turning after signaling. Signal in advance to prevent accidents. 2. Follow the proper procedure when overtaking: When overtaking, turn on the left turn signal in advance and use high beams, low beams, or the horn. On roads without a centerline or with only one lane in the same direction, the front vehicle should slow down and move to the right to allow overtaking when conditions permit. The overtaking vehicle should confirm a safe distance before passing from the left side of the front vehicle. After maintaining a safe distance, turn on the right turn signal and return to the original lane. 3. Check surroundings before reversing: When reversing, first check the surroundings. Do not rely solely on rearview mirrors, parking sensors, or backup cameras. If someone is directing you, they should stand beside the vehicle, not behind it, to avoid being hit. 4. Slow down and observe at intersections: Intersections have vehicles, pedestrians, and non-motorized vehicles from all directions, making them complex. Always look around (while slowing down) when approaching an intersection, regardless of traffic lights or right-of-way. Confirm no vehicles are rushing through before accelerating. 5. Check for tailgating before emergency braking: During emergency braking, check for vehicles behind you. Maintain a safe distance from the front vehicle to avoid rear-end collisions. 6. Maintain a safe distance from the front vehicle: Road conditions are unpredictable. The front vehicle may stop suddenly, or pedestrians may rush out. Control your speed and avoid speeding. Also, keep a safe distance from the front vehicle to allow time to react and avoid accidents. Some vehicles may change lanes without signaling, so a safe distance provides room to respond. 7. Slow down and check surroundings when turning: Always slow down when turning. In some areas, pedestrians and non-motorized vehicles may use the motorway. Check mirrors for pedestrians or non-motorized vehicles and yield to them to avoid collisions. 8. Prefer the middle lane when driving: On roads without a central divider, driving in the middle lane provides time to react if oncoming vehicles pose a risk. With a divider, it allows time to react if someone or a vehicle suddenly emerges. At night, the middle lane prevents being blinded by oncoming headlights, reducing the risk of missing pedestrians or vehicles. 9. Slow down and honk in poor visibility: In areas or weather with poor visibility, honk and slow down to ensure safe passage. 10. Slow down when large vehicles are parked ahead: Large parked vehicles can block visibility. Vehicles, pedestrians, or non-motorized vehicles may suddenly emerge, increasing the risk of accidents. Slow down and proceed only when safe.
1
2
Share

Is It Good to Drive a New Car on the Highway?

It is acceptable to drive a new car on the highway, but you should avoid sudden acceleration, sudden deceleration, and overloading. Here are some precautions for using a new car: 1. Avoid Overloading: Carrying too much weight during the break-in period can damage the mechanical components. Since the powertrain parts of a new car are not fully worn in, aggressive acceleration may cause irreversible damage. Therefore, it is essential to follow the principle of "slow and steady" during the break-in period. 2. Speed Limits for New Cars: For domestic cars, the recommended speed is generally between 40~70 km/h, while for imported cars, it is around 100 km/h. When the throttle is fully open, the speed should not exceed 80% of the maximum speed. The recommended engine RPM during the break-in period is between 2000~4000 RPM.
6
1
Share

Where is the air conditioning filter of Audi A6 located?

The air conditioning filter of Audi A6 is located inside the glove compartment on the passenger side, and it can be seen after opening the cover. The functions of the air conditioning filter include providing fresh air, ensuring safety and hygiene, absorbing harmful substances, and filtering solid impurities. The basic components of a car's air conditioning system consist of the refrigeration system, heating system, ventilation system, control system, and air purification system. Here are some precautions regarding the use of car air conditioning: 1. Regularly add refrigerant: The refrigerant used in car air conditioning is R134a, and it needs to be added periodically. If refrigerant is not added for a long time, it can lead to reduced cooling efficiency and slower cooling speed of the car air conditioning. 2. Regularly clean the car air conditioning: Many bacteria can grow inside the air conditioning system. When cleaning the air conditioning and adding refrigerant, it is essential to go to a professional institution and have experts use professional equipment for the operation.
14
2
Share

Does Lynk & Co belong to Geely?

Lynk & Co belongs to Geely. Lynk & Co is a high-end luxury brand under Geely, specializing in manufacturing premium vehicles. The models under Lynk & Co include the 01, 02, 03, and 05. The 03 is a compact sedan, which is also the first compact sedan under the Lynk & Co brand, and it also has a high-performance version. The dimensions of the Lynk & Co 03 are 4639mm in length, 1840mm in width, and 1460mm in height, with a wheelbase of 2730mm. The Lynk & Co 03 is equipped with features such as three-screen interaction, cloud connectivity, remote app control, 17 intelligent driving assistance technologies, and active and passive safety technologies. In terms of exterior design, the Lynk & Co 03 mainly adds a full-body sporty kit, including optional carbon fiber front lip, front grille, new-style 19-inch dual-tone multi-spoke alloy wheels, rear diffuser, carbon fiber rear spoiler, and quad exhaust pipes.
1
5
Share

After how many kilometers does the Audi A4L require a major overhaul?

Audi A4L requires a major overhaul after driving 100,000 kilometers. The maintenance cycle for Audi vehicles is 3 months or 5,000 kilometers. If the maintenance time is up but the mileage has not reached the standard, the vehicle should still undergo maintenance because maintenance has two indicators: time and mileage, whichever comes first. Here is an introduction to car maintenance: 1. Definition of car maintenance: Car maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain parts of the car, also known as car servicing. 2. Scope of car maintenance: Modern car maintenance mainly includes the maintenance of the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, etc. 3. Purpose of car maintenance: The purpose of car maintenance is to keep the vehicle clean, maintain normal technical conditions, eliminate hidden dangers to prevent failures, slow down the deterioration process, and extend the service life.
17
4
Share

Reasons for Black Screen in Rearview Camera

Car rearview camera black screen may be caused by display screen failure, wiring issues, reverse signal failure, obstructed camera, or camera malfunction. It is best to have it inspected and repaired at a maintenance shop to resolve the issue. Here is some related information about car rearview cameras: 1. Function of car rearview camera: The car rearview camera is a system in the vehicle. This newly developed rearview system is intuitive and clear, allowing the driver to monitor the video feed of the areas on both sides and behind the car in real-time, helping to avoid accidents and theft. 2. Performance of car rearview camera: The car rearview camera system uses a wide-angle far-infrared camera device installed at the rear of the car. Through the display screen inside the car, obstacles behind the vehicle can be clearly seen. Even at night, the infrared feature ensures clear visibility. The professional vehicle-mounted probe has further improved performance in terms of anti-magnetic, anti-shock, waterproof, and dustproof capabilities.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.