Can a C1 driver's license drive a light van?

1 Answers
TravisLynn
07/29/25 12:26pm
A C1 driver's license can drive a light van. There are two requirements for vehicles that a C1 license can drive: the vehicle length should not exceed 6 meters, and the load capacity should not exceed 2 tons. Vehicles that a C1 driver's license can drive include: small cars, small automatic transmission cars, low-speed trucks, and three-wheeled cars. For blue-plate trucks, the driver's license should indicate small passenger cars, light trucks, mini passenger cars, or mini trucks. The process of obtaining a driver's license: 1. Registration, requiring the provision of ID card copies, residence permit copies, etc.; 2. Medical examination, the purpose of which is to check whether the applicant meets the driving requirements in terms of hearing, vision, color blindness, etc.; 3. Taking the theoretical test (Subject 1), which usually covers traffic regulations and driving knowledge; 4. Taking the field test (Subject 2), with common test items including reversing into a parking space, parallel parking, curve driving, etc.; 5. Taking the road test (Subject 3); 6. Taking the safety and civilized driving test (Subject 4).
Was this review help?
19
1
Share
More Forum Discussions

What are the reasons for high car water temperature?

The reasons for high car water temperature: 1. Thermostat failure; 2. Cooling fan not working, which could be due to the temperature control switch not opening or the water temperature sensor malfunctioning; 3. Water pump failure, where the impeller slips or gets stuck, causing the belt to break; 4. Insufficient cooling medium, such as low coolant level or radiator leakage; 5. Incorrect ignition timing and high oil pressure, leading to a discrepancy between the water temperature gauge reading and the actual temperature. When cooling down, never pour cold water on the engine, as this may cause the engine block to crack due to sudden cooling. The correct method is: wear gloves, place a multi-folded wet cloth over the radiator cap, gently unscrew the cap a small gap, wait for the steam to slowly escape, and after the radiator pressure drops, add cold water or antifreeze.
8
0
Share

What is generally done during the first maintenance?

The first maintenance at a 4S shop includes the following aspects: changing the engine oil and oil filter, cleaning the air filter; checking whether the levels of various fluids are normal, inspecting the generator belt and wiper blades for damage; checking whether the tire pressure is normal and if there is any uneven wear, bulging, or damage to the tires; inspecting the chassis, including the brake pads, brake discs, connecting rods, ball joints, CV joints, and any scratches; checking all the switches in the vehicle; and ensuring the lights are functioning properly. Estimated time: Completing all tasks takes about 2 hours. Items needed for the first maintenance include: driver's license; maintenance manual; warranty manual; owner's ID card; vehicle registration certificate; and the vehicle purchase invoice. Take these to the designated first maintenance facility for the vehicle. Note: Make an appointment with the 4S shop in advance. The first maintenance refers to the initial service after the new car has been driven. The specific timing varies by vehicle, usually after driving 1,000 to 3,000 kilometers. The car must undergo the first maintenance on time, neither early nor delayed. The completion of the first maintenance marks the end of the car's break-in period, allowing it to be driven under standard load and normal speed as required by the vehicle. The timing of the first maintenance is calculated from the date of vehicle pickup. There are two indicator values for the first maintenance: mileage and time. Whichever comes first will be the standard. The following inspections and replacements must be completed during the first maintenance of a new car: changing the engine oil, cleaning the three filters (oil filter, fuel filter, and air filter); checking whether the coolant level is normal; inspecting the brake and clutch fluid levels; checking the power steering fluid level and for any leaks at the pipe connections; inspecting the generator, air conditioning, water pump, and belts for aging and tension; checking tire pressure and wear, inflating the tires, and rotating them if necessary. When changing the oil, the oil filter must also be replaced. The choice of oil must refer to the "Vehicle Use and Maintenance Manual," as different vehicle models specify different oil grades. Maintenance precautions: Do not wash the interior of the car with water: Many people clean their cars during holidays, washing the body with water and wiping it with a cloth. It is important to note that the interior of the car should not be directly washed with water. If the floor mats are dirty, use a vacuum cleaner or take them out, scrub them with a brush and detergent, dry them, and then put them back. There are many holes under the rubber mats on the cabin floor. If water enters, it will not dry but will flow through the holes to areas like the transmission, causing corrosion. The best practice is to clean with a vacuum cleaner and then wipe with a cloth to prevent water accumulation. Do not mix different brands of antifreeze: When the antifreeze in the car is low, it is recommended to drain the antifreeze and add the same brand from the beginning. Different brands of antifreeze have different chemical properties. The corrosion inhibitors in one brand may corrode those in another. Different brands of antifreeze use different corrosion inhibitors, so they should not be mixed to avoid unnecessary trouble. Do not lubricate tire bolts and nuts: When bolts on a moving car rust, they are often oiled to function properly again. Some people apply lubricant to the bolts and nuts to prevent rust, but this can pose a safety risk. At high speeds, the bolts and nuts may loosen or even fall off, leading to driving failures. Do not press the accelerator when starting an electronic fuel injection car: The starter of an electronic fuel injection car is different from that of a regular car. Its fuel injection control device can automatically adjust the fuel supply based on the starter's temperature and operating conditions, ensuring smooth starting.
15
4
Share

Which car is the TACQUA?

TACQUA is the first domestically produced model featuring Volkswagen's new logo, a full-scenario SUV crafted by FAW-Volkswagen for young consumers. Below are specific details about the TACQUA: 1. It is suitable for various road conditions and compatible with diverse lifestyle scenarios, offering excellent handling, superior configurations, and a comfortable space. 2. The side profile adopts a dual-waistline design, showcasing the car's robust yet youthful demeanor. 3. It comes with roof rails, complemented by black plastic skid plates and smoked alloy wheels, enhancing both practicality and recreational appeal. 4. The car's dimensions are 4194mm in length, 1760mm in width, and 1601mm in height, with a wheelbase of 2651mm. 5. The vehicle features a trendy full-width taillight design, which, similar to the front, broadens the horizontal visual effect and improves recognition.
1
2
Share

When to Use the Width Indicator Lights?

Width indicator lights are used during dawn, dusk, and rainy or overcast weather. Here is an introduction to width indicator lights: 1. Width indicator lights are warning lights on vehicles, primarily used in low visibility conditions to alert other vehicles. 2. Since the width indicator lights also turn on when the headlights are activated, many drivers do not have the habit of manually turning them on during daily driving. 3. In hazy weather, during evening drives, or in light rain, the width indicator lights can be turned on independently without the need to activate the low beam headlights (as low beams are not very noticeable during the day), making it easier for vehicles in front and behind to identify your car.
12
2
Share

How to Replace the Oil Filter?

Replacing the oil filter involves the following steps: 1. Loosen the oil filter using a specialized wrench (turn counterclockwise). 2. When installing, apply a small amount of oil to the rubber gasket of the new oil filter, then screw on the new oil filter. 3. Add engine oil, then close the oil filler cap, and start the engine to check for any leaks at the oil filter and drain plug. Below is relevant information about oil filters: The function of an oil filter: It is used to remove impurities such as dust, metal particles, carbon deposits, and soot from the engine oil. Classification of oil filters: Full-flow and bypass types.
15
5
Share

Reasons for the Airbag Light to Illuminate

The main reasons and solutions for the airbag light to illuminate are as follows: 1. Loose or disconnected wiring. Solution: Inspect the airbag wiring. 2. Faulty airbag sensor. Solution: Replace the driver-side side airbag sensor. 3. Airbag malfunction. Solution: Check the seat belt sensor, airbag connector, and airbag sensor. 4. Faulty airbag control unit. Solution: Replace the airbag control unit. 5. Presence of fault codes. Solution: Use specialized equipment to clear the fault codes. 6. The light may illuminate during engine self-test and turn off after the self-test is completed, which is a normal phenomenon.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.