Can a C1 Driver's License Drive a 9-Seater Business Vehicle?

1 Answers
OAdriana
07/29/25 3:22pm
C1 driver's license can drive a 9-seater business vehicle. According to the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," the permitted vehicle types for a C1 driver's license are small and mini passenger vehicles, as well as light and mini cargo vehicles; light and mini special-purpose vehicles. A 9-seater business vehicle falls under the category of small passenger vehicles, so a C1 license is permitted to drive it. Additional information: Introduction to Class C driver's licenses: 1. Vehicles permitted for C1 driver's license: small and mini passenger vehicles, as well as light and mini cargo vehicles; light and mini special-purpose vehicles. 2. Vehicles permitted for C2 driver's license: small and mini automatic transmission passenger vehicles, as well as light and mini automatic transmission cargo vehicles. 3. Vehicles permitted for C3 driver's license: low-speed cargo vehicles. 4. Vehicles permitted for C4 driver's license: three-wheeled vehicles. 5. Vehicles permitted for C5 driver's license: small and mini automatic transmission passenger vehicles specially designed for disabled individuals (only allowed for those with right lower limb or both lower limb disabilities to drive).
Was this review help?
8
2
Share
More Forum Discussions

Is the Car Scrapped If the Engine Is Broken?

No, it is not scrapped. You can replace the engine. Below is relevant information: 1. Warranty Service: If the engine has issues during the warranty period, you can contact the car manufacturer for repairs. As long as the malfunction or component damage occurs under normal usage conditions as specified, the manufacturer will provide free repairs or replacement of corresponding parts. 2. Precautions: Regularly clean the fuel system. During the process of fuel being supplied to the combustion chamber through the fuel system, it inevitably forms gum and carbon deposits, which accumulate in the fuel passages, carburetor, fuel injectors, and combustion chamber. This can interfere with fuel flow, disrupt the normal air-fuel ratio, impair fuel atomization, and lead to performance issues such as engine shuddering, knocking, unstable idling, and poor acceleration.
11
0
Share

Where is the windshield washer fluid filler port on the Audi A4L?

Audi A4L windshield washer fluid filler port is located behind the hood hinge on the upper left side of the engine compartment. The washer fluid reservoir in the Audi A4L is situated in the engine compartment with a capacity of approximately 4L. Below is relevant information about the Audi A4L windshield washer system: 1. Cleaning performance: Windshield washer fluid is formulated with multiple surfactants and additives. Surfactants typically possess wetting, penetrating, and solubilizing functions, effectively removing dirt. 2. Antifreeze performance: Containing alcohol and ethylene glycol, it significantly lowers the freezing point of the liquid to prevent freezing and quickly dissolves frost. 3. Anti-fog performance: Forms a monomolecular protective layer on the glass surface. This protective film prevents fog droplet formation, ensuring clear visibility through the windshield.
16
3
Share

What does 'oil maintenance required soon' mean?

"Oil maintenance required soon" is a reminder for the car owner to change the engine oil. Here is the relevant information: 1. Notes: The reminder indicates that the oil should be changed within about 500 kilometers. Mineral oil needs to be replaced within 5,000 kilometers, and should not exceed 6,000 kilometers at most. Semi-synthetic oil can extend the oil change interval to 7,500 kilometers, while full-synthetic oil can be extended to 10,000 kilometers. 2. Car maintenance: Modern car maintenance mainly includes the maintenance of the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, etc.
13
1
Share

What are the dimensions of the Hummer H2?

The dimensions of the Hummer H2 are 5170mm (length), 2063mm (width), and 2012mm (height). Here is some related information about the Hummer H2: 1. The Hummer H2 is a five-door, five-seat SUV equipped with a 6.2-liter V8 naturally aspirated engine. It has a maximum power output of 293 kW and a maximum torque of 574 Nm, with the maximum torque achieved at 4300 rpm and the maximum power at 5700 rpm. 2. It features multi-point fuel injection technology and uses an aluminum cylinder head with a cast iron cylinder block. This engine is paired with a 6-speed automatic transmission.
16
1
Share

What is the standard size of reflective stickers?

3M vehicle reflective stickers generally come in the size of: 5cmX45.72m, 5cm in width and approximately 45.72 meters in length. Relevant regulations: Domestic regulations only require trucks to have reflective strips to enhance safety during nighttime driving. There are no explicit regulations for private cars, so it's optional. However, if applied, they must be installed according to the requirements; otherwise, penalties may be imposed by traffic police if discovered. Requirements for applying reflective film: The visible light transmittance of the front windshield in the driver's viewing area and the areas used for observing external rearview mirrors while driving should be greater than or equal to 70%. No mirrored reflective sunshade film should be applied to any window glass.
7
4
Share

What are the three methods for detecting engine knock?

Detecting cylinder pressure, detecting engine vibration, and detecting cylinder temperature. Here is the relevant information: 1. Knock: Knock, commonly known as piston slap or pinging. Knock is an abnormal combustion phenomenon that occurs during the engine combustion process. Simply put, "knock" is an abnormal combustion phenomenon in the engine. Knock is caused by abnormal combustion leading to abnormal pressure in the combustion chamber. When knock occurs, the engine produces a knocking sound. 2. Installation location: The knock sensor is placed in different positions on the engine block or cylinder. When vibration or piston slap occurs, it generates a small voltage peak; the greater the piston slap or vibration, the larger the peak voltage produced by the knock sensor. A certain high frequency indicates knock or piston slap. Knock sensors are usually designed to measure frequencies in the range of 5 to 15 kHz.
2
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.