Can a 7-Seater Vehicle Operate on Didi?

2 Answers
Gertrude
07/28/25 10:36pm
Some regions allow 7-seater vehicles to operate on Didi. All eligible vehicle models must be listed in the Didi partnership program. In certain areas, 7-seater commercial vans with a base price exceeding 70,000 RMB can register for Didi services. However, other regions prohibit 7-seater commercial vehicles from registering due to their excessive wheelbase length, which fails to meet Didi's vehicle standards. Below are precautions for using Didi: 1. Before boarding, always verify that the license plate matches the vehicle model and observe the driver's behavior. If anything seems unusual, you can cancel the order via the app. During the ride, monitor whether the driver follows the planned route. If deviations occur, maintain phone contact with a trusted person. 2. If you notice anything suspicious, seek assistance or report it immediately. Avoid taking rides late at night, especially when traveling alone. Stay vigilant to protect your valuables and opt for the rear seats to minimize risks in case of accidents.
Was this review help?
6
5
Share
Gwen
08/12/25 3:05am
As a family car owner, I've used my seven-seater to drive for Didi, and it feels quite suitable. The platform allows registration as a carpooling service, which means you can take more passengers, such as orders for family outings. However, the fuel consumption is indeed higher, costing a few extra cents per kilometer in urban conditions, but it can be offset when there are more orders. Make sure your vehicle passes the annual inspection and the number of seats matches the app's requirements, as these can vary by city. I recommend downloading the Didi app to check local rules—you might even catch some big orders during the peak travel season. That's what I did, and after a few trips, I got the hang of it—it's safe and convenient.
Was this review help?
11
4
Share
Expand All
More Forum Discussions

How to Deal with Wrinkles in Car Film Over Time?

If it is still under warranty, you can ask the repair shop to handle it. If the warranty has expired, you can first try using a hairdryer to heat the wrinkled area while pressing it flat. If this doesn't work, it may be due to the quality of the film. There is no other solution except to replace the film entirely. Related information is as follows: 1. Function: Wrinkles in car window film are usually caused by unprofessional manual application or poor-quality film. The main functions of car window film are to block UV rays, reduce heat, prevent injuries from shattered glass, reduce glare, and protect personal privacy through the one-way visibility feature of the film. 2. Lower Fuel Consumption: Additionally, it can minimize damage to interior items and passengers caused by UV exposure. By reflecting sunlight physically, it lowers the car's interior temperature, reducing the need for air conditioning, thereby lowering fuel consumption and saving costs.
15
5
Share

Is it okay to rain after a full car color change wrap?

It is okay to rain after a full car color change wrap. Here are the relevant details: 1. Products include: transparent film, car electroplating film, pearl film, glossy film, matte film, painting film, leather grain film, brushed film, electroplating film, electric light metal film, matte metal film (referred to as matte ice film). Nowadays, color change films are mainly divided into domestic and imported categories. Domestic color change films are inferior to imported ones in terms of post-application effects and durability. 2. Rich color options: Car color change films use a variety of rich and colorful films to change the overall or partial appearance of the car through full coverage and adhesion. Car color change films are mainly attached to the car surface through high molecular polymer materials and are easy to remove.
8
3
Share

How to Check if Brake Pads Need Replacement

Here is a detailed introduction to methods for checking whether brake pads need replacement: 1. Check thickness: New brake pads are generally about 1.5 cm thick. When worn down to one-third of their original thickness (less than 5 mm), immediate replacement is recommended. 2. Listen for sounds: If metallic scraping noises occur during braking, this may indicate the brake pads have worn down to their minimum thickness, causing the wear indicators on both sides to contact the brake disc and produce abnormal sounds, requiring prompt replacement. 3. Check warning indicators: Some vehicle models feature brake wear sensors. Excessive pad wear will cause the sensor wire to contact the brake disc, altering resistance and generating current. This detected signal triggers a brake pad warning light on the dashboard. 4. Feel the pedal: If the brake pedal feels too light or braking requires excessive effort with reduced stopping power, this indicates severe brake pad wear with insufficient thickness, also necessitating immediate replacement.
7
1
Share

What is the China III Emission Standard?

National Emission Standard Stage III is the abbreviation. Below is a partial introduction to the China III Emission Standard: 1. Introduction: The China III Emission Standard is equivalent to the Euro III emission standard, with the content of tailpipe pollutants matching that of Euro III. The key difference is that new vehicles must be equipped with an OBD (On-Board Diagnostics) system. 2. Considerations: For motor vehicle pollutant emissions to stably meet the China III standard, vehicles must be equipped with technical measures that ensure emissions comply with the China III standard, while also using fuel that meets the Euro III standard. 3. About OBD: OBD stands for On-Board Diagnostics. The system features an increased number of detection points and enhanced detection systems, with oxygen sensors installed at both the inlet and outlet of the three-way catalytic converter. It ensures compliance by continuously monitoring vehicle emissions in real-time, thereby better guaranteeing the enforcement of the Euro III emission standard.
13
4
Share

Where is the Cigarette Lighter Fuse Located?

Car cigarette lighter fuse is located at the lower left side of the steering column. Below are detailed introductions about the fuse box: 1. Function: The fuse box is an overcurrent protection switch, primarily serving to control circuit operation. There are numerous circuits in a car, and fuses play a protective role for these circuits. When the circuit temperature is too high or the current is excessive, the fuse can blow to protect the circuit. 2. Impact of Blowing: There are many fuses and relays inside the car fuse box. When a fuse blows, certain functions of the car will be affected. After a fuse blows, it needs to be replaced with a new one. 3. Replacement Precautions: When replacing a fuse, use a specialized clip to remove the fuse. The fuse box in the engine compartment is generally located near the battery, while the fuse box in the cabin is usually situated at the main driver's position or inside the glove compartment of the passenger side.
4
2
Share

What are the symptoms of a faulty brake caliper?

Here are the specific details about a damaged car brake caliper: 1. Soft Brake: When applying the brake, if you feel that the braking sensation is noticeably soft and the stability decreases with continuous braking, it could be due to poor sealing of the master cylinder or caliper piston, or a rupture somewhere in the brake line causing oil leakage. 2. Sudden Brake Failure: If you experience a momentary loss of braking while driving, check if there is a shortage of brake fluid and then inspect the master cylinder, caliper, and oil lines for any traces of brake fluid. 3. Brake Pulling: This may be caused by rust on the brake caliper, piston expansion, or uneven brake wear. 4. Brake Pedal Not Returning or Slow to Return: If the brake pedal does not rise or offer resistance after being pressed, inspect the master cylinder and caliper components for damage.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.