Can a 45-liter fuel tank be filled up to 55 liters?

Where is the car reverse radar switch located?

Reverse radar switch is the switch for the reverse gear. Below are the specific details about the reverse radar: 1. The reverse radar is a safety auxiliary device when parking or reversing the car. It informs the driver about surrounding obstacles through sound or more intuitive displays, alleviating the troubles caused by the driver's need to look around when parking, reversing, or starting the vehicle. It also helps eliminate blind spots and unclear vision. 2. When reversing, the reverse radar uses ultrasonic principles. The ultrasonic sensor installed on the rear bumper sends out ultrasonic waves that reflect off obstacles. The system then calculates the actual distance between the car body and the obstacle and provides this information to the driver. 3. The reverse radar mainly consists of ultrasonic sensors, a controller, and a display or buzzer.

12

4

Share

What is the Cause of CAN Bus Failure?

Here are the reasons for failures in the CAN bus system: 1. Faults caused by the vehicle's power system. The operating voltage of automotive electronic control modules is generally between 10.5-15.0V. If the working voltage provided by the vehicle's power system is abnormal, it can cause certain electronic control modules to malfunction temporarily, leading to communication issues in the entire vehicle CAN bus system. 2. Link faults in the vehicle CAN bus system. Short circuits, open circuits, or physical changes in the communication lines that cause signal attenuation or distortion can result in multiple electronic control units malfunctioning, rendering the CAN bus system inoperative. 3. Node faults in the vehicle CAN bus system. Nodes are the electronic control modules in the vehicle CAN bus system, and node faults refer to failures in these modules. This includes software faults, such as defects or conflicts in the transmission protocol or software programs, which can cause chaos or complete failure in the vehicle CAN bus system communication.

11

5

Share

What happens if the air filter is not replaced for 2 years?

The consequences of not replacing the air filter for 2 years are as follows: 1. It will affect the engine's air intake, leading to a lack of power during acceleration; 2. The engine will experience increased wear and carbon buildup, shortening its lifespan; 3. The phenomenon of "cylinder scoring" may occur. Here is an introduction to the car air filter: 1. The general replacement cycle for an air filter is 10,000 to 20,000 kilometers, which is heavily influenced by driving conditions. If the environment is poor, it needs to be replaced earlier. If the air filter is replaced after 30,000 to 40,000 kilometers, it mainly depends on the condition of the air filter. It is best not to go too long without replacement and to replace it within the specified time. 2. When installing a new air filter, pay attention to the correct orientation. There is a protruding plastic tab on the lower right side of the air filter to prevent incorrect installation. To ensure proper installation, the plastic tab must be secured into the slot of the filter housing.

18

3

Share

Are Oil Filters Universal?

Oil filters are not universal, but they can be shared within the same vehicle series. Below is a detailed introduction to oil filters: 1. The oil filter element is the oil filter itself. 2. The function of the oil filter is to remove impurities, gums, and moisture from the oil, delivering clean oil to various lubrication points. 3. There are three levels of oil filters: the oil strainer, the primary oil filter, and the secondary oil filter. (1) The strainer is installed in the oil pan before the oil pump and uses a metal mesh design. (2) The primary oil filter is installed after the oil pump and is connected in series with the main oil passage. It mainly includes metal scraper type, sawdust filter element type, and microporous filter paper type. (3) The secondary oil filter is installed after the oil pump and is connected in parallel with the main oil passage. It mainly includes microporous filter paper type and rotor type.

14

1

Share

What does MG ECO mean?

ECO refers to the vehicle's economical driving mode function. ECO is an English abbreviation formed by combining Ecology (environmental protection), Conservation (energy saving), and Optimization (power). The Eco mode is further divided into active Eco driving mode and passive Eco driving mode. When the ECO indicator light on the dashboard illuminates, it indicates that the vehicle's economical mode has been activated. Eco mode can be categorized into active and passive types. The difference lies in the fact that the active type has a dedicated button, allowing the driver to choose whether to activate it. When the driver presses the Eco mode switch, the dashboard indicator light immediately turns on, and the vehicle automatically begins adjusting settings such as throttle opening, transmission shift logic, and air conditioning output power. The passive Eco mode does not have a dedicated button; when the dashboard ECO indicator light turns on, it merely serves as a reminder function. The Eco system automatically evaluates your driving behavior. If your current driving operation achieves the optimal fuel supply, the dashboard will simultaneously display the ECO indicator light. Most vehicles employ the active Eco driving mode, meaning they have a dedicated switch button. Therefore, during daily driving, we can activate the Eco mode. However, it is unnecessary to enable Eco mode when the speed exceeds 120 km/h, during idling, in N/P gear, or in manual mode, especially when climbing hills. Doing so would not reflect the fuel-saving characteristics of Eco mode and could instead impact the vehicle's power performance. Additionally, the Eco mode typically becomes ineffective under the following circumstances: When the vehicle speed exceeds 120 kilometers per hour, the system prioritizes speed, causing the Eco mode to deactivate automatically. During idling or when in N/P gear or manual mode, the Eco mode may also become ineffective. When high torque output is required, such as when climbing a hill, the engine control unit prioritizes ensuring sufficient power to drive the vehicle, and the Eco mode will not function under these conditions either.

1

Share

How to Use the Touching Lock Feature on the Magotan?

The method to use the touching lock feature on the Magotan is as follows: 1. When opening the door, pull the door handle with your thumb tucked into your palm, avoiding contact with the indentation point. 2. To lock the car, simply touch the indentation point with any finger; it is essential to follow these steps precisely, as the vehicle cannot independently determine whether the action is meant to lock or unlock the car. 3. Additional Information: The Magotan is closely related to the Passat B6, originating from the Future B6, and it is the first B-class sedan to be produced and sold by FAW-Volkswagen since its establishment. The name "Magotan" symbolizes confidence, decisiveness, and dynamism; "tan" represents soaring, surpassing, and passion.

20

0

Share

Can a 45-liter fuel tank be filled up to 55 liters?

Where is the car reverse radar switch located?

What is the Cause of CAN Bus Failure?

What happens if the air filter is not replaced for 2 years?

Are Oil Filters Universal?

What does MG ECO mean?

How to Use the Touching Lock Feature on the Magotan?

Will a 30 km/h speed limit on highways actually be monitored by speed cameras?

What vehicles can a C1 driver's license drive?

What are the precautions for driving in rainy weather?

What Causes Low Oil Pressure?