Can 98 and 95 be mixed?

1 Answers
DeAddyson
07/29/25 2:23pm
95 gasoline and 98 gasoline can occasionally be mixed, but it is not recommended to mix them for a long time. The following is a specific introduction about gasoline: Long-term mixing of gasoline can cause engine knocking. Gasoline is a mixture. The gasoline grade we usually come into contact with refers to the anti-knock index of gasoline (i.e., the octane number). Strictly speaking, 95 gasoline and 98 gasoline cannot be mixed. However, their chemical composition and other aspects are relatively similar, with strong anti-knock performance. To ensure vehicle safety, they should still be used separately. In some areas, there is also low-grade 90 gasoline. If it is mixed with high-grade gasoline, it will cause knocking, insufficient power, and other phenomena, affect the service life of spark plugs, and bring more exhaust pollution. The density of 98 gasoline is generally above 0.74. 98 gasoline is gasoline whose octane number is equal to a mixture of 98% isooctane and 2% n-heptane. The advantage of 98 gasoline is "two highs and two lows", that is, higher anti-knock performance and power performance, and lower harmful substances and exhaust pollution in gasoline. 95 gasoline has strong anti-knock performance and will not be compressed and ignited under high pressure, ensuring that the engine is at the optimal ignition advance angle, and the power output is not affected. The gasoline grade also represents the anti-knock performance of the fuel. The larger the grade, the better the anti-knock performance. Anti-knock performance refers to the ability of gasoline to resist knocking when burning in the engine. It is the primary indicator of gasoline combustion performance. Knocking is caused by abnormal combustion of gasoline in the engine. The octane number is the target of gasoline anti-knock performance. The higher the octane number, the stronger the anti-knock performance, and the higher the compression ratio, the higher the pressure in the combustion chamber. If gasoline with low anti-knock performance is used, knocking is more likely to occur.
Was this review help?
13
1
Share
More Forum Discussions

Where is the trunk opening button on the Jetta?

Jetta trunk switch is located on the driver's side door panel, with a button marked with the trunk symbol being the trunk switch. The following is a related introduction about the Jetta trunk: 1. The Jetta trunk has an electric switch, which can be opened via the button on the driver's side door panel. When the car is turned off, a single press will open it, while when the car is just started, you need to hold the button for 3 seconds to open it. Alternatively, you can directly use the trunk key to twist into the trunk lock to open it. The dimensions of the Volkswagen New Jetta trunk are 1000mm in width, 590mm in height, and 1040mm in depth, with a volume of 466L. 2. The trunk space is relatively large, meeting the daily storage needs of families. The driver can open the trunk for others via the door panel button without getting out of the car. There is a light inside the trunk, making it convenient for the owner to take or place luggage at night. The car tools have designated placement areas, preventing noise caused by shaking. However, the lining material is relatively hard, making it less prone to deformation even when heavy objects are placed on it.
13
5
Share

Is it necessary to upgrade from 17-inch to 18-inch wheels?

Modifying vehicle wheels to a larger size can affect the stability of the vehicle, so it is not necessary to upgrade from 17-inch to 18-inch wheels. Moreover, altering the wheel size of a vehicle is illegal. After modifying the wheels, it is mandatory to change to tires of the same type; otherwise, the vehicle will not be able to complete registration within the stipulated time. Points to note when changing wheels: You need to complete the registration procedures. Modifying the wheel size of a vehicle involves altering the vehicle's appearance data. Within ten days after the modification, you must bring the vehicle's license and registration certificate to the local vehicle management office to complete the registration procedures. Otherwise, it will be considered an illegal modification. If you switch to 18-inch wheels, it may cause the speedometer to display inaccurately because the vehicle's design and parameters have already been calibrated. Modifying the style and color of vehicle wheels is legal. Changing the style and color of the wheels will not affect the use of the original tires. You can safely modify and use them, and the vehicle can be driven on the road without any impact on the annual inspection.
9
3
Share

What are the reasons for the failure of Volkswagen door window lift?

The reasons for the failure of Volkswagen door window lift include: 1. The lift function is turned off: Most modern cars are equipped with a function to independently control the window lift of the passenger side and the two rear doors. After pressing this function switch, the window lift switch on the door cannot be used to control the window. This switch is usually located on the driver's side door panel. 2. There are foreign objects or dirt in the window guide channel: Many higher-end models are equipped with an anti-pinch function for door windows. Foreign objects in the window guide channel, aging guide channel rubber, or excessive dust accumulation can trigger the anti-pinch function, preventing the window from rising. 3. Overheating of the window lift motor: The lifting and lowering of door windows are controlled by the lift motor. Frequent operation of the window can cause the lift motor to overheat, entering an overheat protection mode. At this time, the window lift function will temporarily fail until the motor temperature drops and returns to normal. 4. Faulty control switch: In older vehicles, due to frequent use of the lift function, control switch failures are common. Initially, it may require pressing harder to get a response, and eventually, it may fail completely.
2
0
Share

Where is the hood release on a Mercedes-Benz?

Mercedes-Benz vehicles have their hood release lever located under the dashboard on the driver's side. Here is some related information: 1. Mercedes-Benz is a German automobile manufacturer, and many of its models have been locally produced in China. The domestically produced Mercedes-Benz models include the C-Class, A-Class, E-Class, GLA, GLB, GLC, EQC, and others. 2. The EQC is a pure electric SUV from Mercedes-Benz. Its dimensions are 4774 mm in length, 1890 mm in width, and 1622 mm in height, with a wheelbase of 2873 mm. The EQC is a five-door, five-seat SUV with dual motors. It comes in both low-power and high-power versions. The low-power version has a total motor output of 210 kW, while the high-power version delivers 300 kW with a total torque of 730 Nm. The EQC uses ternary lithium batteries across all models, which offer higher energy density and lighter weight. 3. The cathode of ternary lithium batteries is made from ternary materials. Some use nickel, cobalt, and manganese, while others use nickel, cobalt, and aluminum. 4. The EQC features a double-wishbone independent suspension at the front and a multi-link independent suspension at the rear.
16
5
Share

Is It Normal for the Gear Lever to Make Noise When Braking in P Gear?

Normal. This is the operation of the transmission gear lock solenoid valve. When the brake is not pressed, it is in a locked state. When the brake is pressed, it unlocks, resulting in the sound of the solenoid valve. Below are specific reasons for abnormal noises when braking in a car: 1. Improper installation of brake pads: When installing new brake pads, if the old brake disc is not polished, it can lead to improper fit. Improper installation or installing new brake pads without polishing the old disc can cause the new pads to rub directly against the uneven surface of the old disc, eventually leading to uneven wear of the new brake pads. 2. Brake system malfunction: There may be defects in the brake system itself, causing the brake pads to only partially contact the brake disc. This increases the pressure per unit area on the brakes, resulting in abnormal noises. It is recommended to check components such as the caliper and guide pins. 3. Presence of foreign objects: Foreign objects can cause the contact surfaces to not fit properly, leading to abnormal noises.
3
1
Share

How to Solve the Oil Burning Issue in Haval H7?

Haval H7 burns oil because the engine's lubricating oil film tends to break when the engine operates at extremely high speeds, leading to poor lubrication and dry friction in rotating parts. The solution is to ensure that the oil is filled according to specifications. If the oil level exceeds the midpoint, the excess oil should be extracted by the mechanic. Additionally, the oil level should be checked the next day before driving. Relevant information about engine oil is as follows: 1. Introduction: Engine oil, also known as engine lubricant (English name: Engine-oil), has a density of approximately 0.91×10³ (kg/m³). It serves to lubricate and reduce friction, assist in cooling, seal against leaks, prevent rust and corrosion, and provide shock absorption. It is often referred to as the "blood" of a car. 2. Composition: Engine oil consists of base oil and additives. The base oil is the main component of the lubricant, determining its basic properties, while additives compensate for and improve the shortcomings of the base oil, providing new characteristics. Additives are an essential part of the lubricant.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.