Can 4 Liters of Engine Oil Be Taken on High-Speed Trains?

Can a Car Be Charged If It Starts But Doesn't Move?

If a car starts but doesn't move, it can still be charged. However, the prerequisite is to ensure that all electrical appliances in the car (except for the engine operation) are turned off. Below are the specific details about battery charging: 1. As long as the generator is working, it can charge the battery, and the power source of the generator comes from the engine. 2. After the car starts, the engine begins to work, and it transmits power to the generator via a belt, initiating the charging process for the battery. 3. When the vehicle is in motion, pressing the accelerator increases the engine's speed, providing more power to the generator. Consequently, the generator's output increases, leading to more charging for the battery. 4. During idle operation, the generator runs at a slower speed, resulting in limited power output. 5. The generator does not charge the battery indefinitely. The battery is equipped with a sensor; if the sensor detects that the battery is fully charged, it will stop further charging.

6

5

Share

Where to Place the ETC Device on the Windshield?

The ETC device is generally installed in the upper middle part of the windshield for passenger vehicles, while for large vehicles like trucks and buses, it is installed in the lower middle part. The suitable installation position should be no lower than 1.2 meters and no higher than 2.5 meters, with an installation angle between 30 to 90 degrees. For vehicles with factory-installed or aftermarket explosion-proof film, which may affect microwave signal transmission, the device should be installed in the microwave window area. ETC stands for Electronic Toll Collection. To apply for an ETC device, you need to provide the original and photocopies of the vehicle owner's valid ID and vehicle registration certificate. If someone else is handling the application, they must also bring their valid ID. The photocopy of the vehicle registration certificate should include the page with the most recent annual inspection stamp. Additionally, a bank card for deducting highway toll fees is required, and the vehicle must be registered under the name of an individual aged between 18 and 60. For company vehicles, the required documents include: A letter of introduction from the vehicle owner (with company seal); a photocopy of the organization code certificate or business license (with company seal); the original ID of the agent; the original vehicle registration certificate; and the vehicle to be registered for ETC. Here are some considerations for installing ETC: Do not obstruct the driver's view. The best location is behind the rearview mirror: Many car models have windshields with a steep angle, which can reduce the driver's field of vision. Installing the ETC device without considering this may increase blind spots. Placing it behind the rearview mirror on the right side can help avoid obstructing the view. Do not interfere with charging: The ETC device requires power but generally does not need charging or battery replacement, as it has a built-in solar panel for self-charging. Therefore, avoid installing it on the windshield's blackened areas or positions that may block the solar panel. Once installed, do not remove it casually: The adhesive button in the middle is an anti-tamper lever connected to a switch. After installation, the windshield presses the lever in. If removed, the lever pops out, triggering the switch and locking the device, rendering it unusable. You would then need to visit an ETC service point to unlock it. This feature prevents multiple vehicles from sharing one device. When using ETC, note the following: The ETC transaction sensing range is 8 meters. To avoid paying for the vehicle in front due to its faulty ETC device, maintain a distance of at least 10 meters. The ETC lane recognizes vehicles at a speed of 20 km/h; driving too fast may result in failed fee deductions. Also, insufficient balance on a debit card linked to ETC can cause payment failures.

5

Share

Validity Period of Temporary License Plates for New Cars in Shenzhen

The validity period of temporary license plates for new cars in Shenzhen is 15 days. Below is the specific process for obtaining temporary license plates for a new car: 1. First, you need to pay the vehicle purchase tax, purchase insurance for the new car, and undergo criminal investigation inspection. 2. Then, non-exempt vehicles must pass the inspection line, make payment and fill out forms, take rubbings and photos, and collect the necessary documents for license plate registration. 3. You need to submit the documents at the vehicle management office, sign as the owner, and have the vehicle undergo an external inspection and confirmation by a police officer. 4. Finally, select the license plate number and receive the receipt, have the license plate securely sealed, install the plate, and receive the vehicle registration certificate and license. 5. The validity period of a temporary movement permit is generally 3 days, while the temporary license plate is valid for 15 days. The maximum period from purchasing a new car to officially registering it is generally 3 months. If this period is exceeded, a certain late fee must be paid as per regulations. The timing of registration after purchasing a car is entirely up to the owner.

11

5

Share

What Causes Frequent Blowing of Automotive Fuses?

Below are the specific reasons for the frequent blowing of automotive fuses: 1. The fuse blows in the middle between two tightening screws. The fuse becomes thinner and blows as the tightening screws are tightened, usually due to the absence of washers or washers rotating with the screws. 2. Overloading. New electrical devices are added to the circuit, exceeding the safe current allowed by the fuse, or the fuse selected is too small. 3. Short circuit. A short circuit in the circuit or electrical device causes excessive current, leading to the fuse blowing. 4. The fuse blows at the root of the tightening screw. Loose or sparking tightening screws cause the fuse to blow; excessive tightening pressure flattens the fuse, reducing its current-carrying capacity and causing it to blow; loose wire terminal screws cause sparking when current passes, overheating the terminal plate and increasing the thermal load on the fuse, leading to blowing.

19

0

Share

What to Do If ETC Fails to Scan When Exiting the Highway?

If you find that the card was not scanned while traveling within the province, you need to promptly contact the toll station staff to have the card scanned and pay the fee to avoid affecting subsequent use. If the card was not scanned at an out-of-province highway exit, please consult the local ETC service hotline for specific handling procedures. How ETC Works: Through the onboard electronic tag installed on the vehicle's windshield, specialized short-range communication is established with the microwave antenna in the ETC lane at the toll station. This utilizes computer networking technology to perform backend settlement processing with the bank, thereby allowing vehicles to pass through highway or bridge toll stations without stopping while still paying the toll. Benefits of Installing ETC: Saves time by eliminating the hassle of waiting in line. Green and environmentally friendly, as vehicles pass through toll stations without stopping, reducing noise and exhaust emissions and minimizing pollution. Reduces wear and saves costs by decreasing the frequency of vehicle starts and stops, lowering wear and fuel consumption. Users also enjoy a 5% discount on toll fees. Improves efficiency, as ETC lanes can theoretically increase vehicle throughput by 2-3 times, making traditional ETC more updated, faster, and more high-tech. Compared to license plate payment, ETC technology is more mature and advantageous.

7

2

Share

How to Drive an Automatic Transmission Car for Better Fuel Efficiency?

Here are specific methods for driving an automatic transmission car to save fuel: 1. Utilize coasting. This does not mean coasting in neutral; do not shift to "N" while driving an automatic car. Instead, release the accelerator pedal to let the car coast using its momentum, which can save some fuel. 2. Start gently. Since the engine is cold and the water temperature is not yet at normal operating conditions, it consumes more fuel. After starting the car, let it warm up for about a minute. 3. Anticipate traffic lights. If you cannot pass through, release the accelerator early to control speed and avoid sudden braking, which can save over 30% of fuel.

7

2

Share

Can 4 Liters of Engine Oil Be Taken on High-Speed Trains?

Can a Car Be Charged If It Starts But Doesn't Move?

Where to Place the ETC Device on the Windshield?

Validity Period of Temporary License Plates for New Cars in Shenzhen

What Causes Frequent Blowing of Automotive Fuses?

What to Do If ETC Fails to Scan When Exiting the Highway?

How to Drive an Automatic Transmission Car for Better Fuel Efficiency?

Are Hazard Warning Flashers the Same as Emergency Flashers?

What to Do If Coolants Are Mixed?

What are the reasons for the car's one-button start not responding?

What are the symptoms of aging engine mounts?