Buzzing Noise During Car Acceleration

2 Answers
StMolly
07/29/25 1:49am
Acceleration with a buzzing noise may be caused by the following reasons: 1. Transmission noise: One of the main sources of noise could be friction within the transmission, possibly due to worn transmission bearings or insufficient lubrication fluid. The transmission is one of the more precise and complex components in a vehicle. If there is noise during driving that disappears when the clutch pedal is depressed, it is likely an issue with the transmission components. The gear teeth in the transmission are usually loosely fitted on the shafts, which are equipped with needle bearings. If the rolling bearings of a particular gear are damaged, the meshing will be affected, leading to noise due to the lack of radial positioning. 2. Valve noise: A 'ticking' sound from the engine after starting, especially when the engine is cold, is typically valve noise. This occurs because the oil pressure hasn't built up yet, and the valves aren't properly lubricated. The sound usually subsides after a short while. 3. Engine issues: If the buzzing sound is indeed from the engine, check if the RPM is unusually high. If the RPM increases significantly during acceleration while the vehicle speed rises slowly, this usually indicates clutch slippage, requiring replacement of the clutch assembly.
Was this review help?
8
1
Share
DiColton
08/12/25 5:52am
Recently I encountered a similar issue - the annoying humming sound during acceleration is usually caused by unbalanced tires, with vibrations transferring to the cabin at high speeds. Worn wheel bearings are also common, with the humming sound increasing with speed, and in severe cases the wheel might even lock up. It could also be wind noise - faster airflow during acceleration, so check if door seals or exterior trim are loose. I suggest first identifying the sound source: front could indicate loose engine belt, rear might suggest exhaust leak. You can check tire balance yourself at a tire shop to save time and money, but safety first - older cars should get comprehensive inspections to prevent accidents.
Was this review help?
17
2
Share
Expand All
More Forum Discussions

What Causes the Steering Wheel to Snap Back?

The reasons for the steering wheel snapping back: 1. The front left leaf spring's front mounting bolt is loose or the leaf spring is broken; 2. The left steering wheel has shifted backward. If the steering wheel suddenly rotates on its own, immediate repair is required to avoid affecting normal driving. The steering wheel, also known as the handwheel, typically consists of a skeleton and foam. Common steering wheels feature various control switches, such as acceleration/deceleration buttons and cruise control buttons. The steering wheel has corresponding mounting clips or screw holes for the driver's seat airbag, and the horn contact is pressed into the skeleton. The steering wheel is the tool for controlling the direction of the car and is one of the important components of the vehicle. When driving, both hands should firmly grip the steering wheel to prevent loss of control and potential traffic accidents. After replacing tires, a four-wheel alignment should be performed to prevent steering deviation.
19
4
Share

Is the Sagitar a B-segment car?

The Sagitar is not a B-segment car; it is positioned as a compact car. The Sagitar has a length of 4753 mm, a width of 1800 mm, a height of 1462 mm, and a wheelbase of 2731 mm. The exterior design follows the family-style design, with a horizontally stretched front grille decorated with chrome trim. The headlights on both sides have a relatively moderate shape but offer excellent recognition and average aggressiveness. This car is equipped with two engines: a 1.2T and a 1.4T, paired with two types of transmissions: a 5-speed manual transmission and a 7-speed dual-clutch transmission. The 1.2T engine has a maximum output power of 85 kW and a maximum torque of 175 Nm, while the 1.4T engine has a maximum output power of 110 kW and a maximum torque of 250 Nm.
15
0
Share

What does the 'push' mean in Toyota Prado 4WD?

Toyota Prado 4WD 'push' refers to the four-wheel drive mode. Here are some details about the Prado: 1. Exterior: The vehicle has a body length of 4840 mm, width of 1885 mm, height of 1890 mm, wheelbase of 2790 mm, front track of 1585 mm, rear track of 1585 mm, minimum ground clearance of 215 mm. It is a five-door, seven-seat SUV with an 87-liter fuel tank capacity. 2. Configuration: It performs exceptionally well on unpaved roads. The domestic version is the 2019 model, which has been discontinued. It is equipped with a 3.5-liter 280 horsepower six-cylinder naturally aspirated engine and a six-speed automatic transmission.
20
4
Share

Will fuel overflow when filling up the tank?

Fuel can overflow when filling up the tank, but modern gas stations commonly use self-sealing nozzles that automatically shut off when the tank is full. Fueling precautions: Use automotive gasoline only. Improper fuel entering the fuel system may damage the fuel system and engine. Do not use gasoline containing methanol or alcohol. Avoid spilling fuel on painted surfaces to prevent paint damage. If the fuel door is frozen and cannot be opened, gently push or tap the door to remove ice and open it. Prevent excessive fuel pressure that may cause spraying. Solutions for fuel overflow: For gasoline spills, use a broom to disperse the fuel and isolate the area, keeping people and vehicles away until it evaporates completely. For diesel spills, use fire sand to absorb the fuel by sweeping back and forth, then place the oil-saturated sand in direct sunlight on a concrete surface to dry.
3
2
Share

What should be paid attention to during the car break-in period?

During the car break-in period, the following points should be noted: 1. Try to keep the vehicle in a light load state and avoid overloading; 2. Always pay attention to the operating status of various components of the vehicle, such as water temperature and oil pressure; 3. Drive at a constant speed, avoid violent and aggressive driving, and cultivate good driving habits. The break-in period generally refers to the process of contact, friction, and meshing of mechanical components during initial operation, also known as running-in. The car break-in period refers to the initial driving stage of a new car or after a major overhaul, usually 1000 to 1500 kilometers, which is the basic mileage to ensure full contact, friction, adaptation, and shaping of mechanical parts. During this period, the ability of various components of the car to adapt to the environment can be adjusted and improved, and the protrusions on the parts can be worn off.
12
0
Share

How to Open the Hood of the Buick LaCrosse?

The method to open the hood of the Buick LaCrosse: 1. Locate the hood release button below the left side of the steering wheel and press it, which will release the exterior hood; 2. Slightly lift the exterior hood and prop it up; 3. Extend the hydraulic strut to its full length to secure the hood in place. The Buick LaCrosse is a 4-door, 5-seater sedan with a trunk capacity of 523L. Its body dimensions are 5026mm in length, 1866mm in width, and 1459mm in height, with a wheelbase of 2905mm. The LaCrosse is equipped with a 9-speed automatic transmission, and its engine delivers a maximum power of 124kw. The vehicle features a front MacPherson independent suspension and a rear multi-link independent suspension.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.