Brief Description of the Steps for Removing and Dismantling Car Wheels?

How to Start a Manual Transmission Car with a Dead Battery?

Turn the key to the ignition position, press the clutch pedal, release the handbrake, set the gear to 1st or 2nd, keep the clutch pedal pressed, slowly release the clutch while stepping on the accelerator. First, open the hoods of both cars, connect the positive and negative terminals between the two cars, then start the other car, rev the engine, and try starting your car. Use a sturdy tow rope to securely connect the front and rear of both cars, then start the front car to pull the rear car. In extreme cases, you can call emergency services for assistance.

12

5

Share

How to reset the tire pressure light on a Toyota Levin?

This situation usually indicates a very slow air leak, making it difficult to immediately identify which tire is affected. In such cases, you can use a tire pressure gauge to measure the pressure. If the warning light is on, you should visit a 4S shop to replace the tire. When any tire exceeds 3.0 bar, it can trigger the tire pressure monitoring light to illuminate. In this case, you need to reduce the tire pressure. If a tire has low pressure, high-speed driving can cause the tire temperature to rise, leading to an increase in tire pressure. In such situations, you should promptly stop to rest or replace the tire with a spare. When the tire pressure drops below 1.8 bar, it will cause the tire pressure monitoring light to come on. Therefore, you should regularly check whether the tire pressure monitor is functioning properly.

3

5

Share

Do You Need to Press the Brake Every Time You Shift Gears in an Automatic Transmission?

Whether to press the brake when shifting gears in an automatic transmission car depends on the actual situation. The details are as follows: 1. Shifting between D, D3, and D2 while driving does not require pressing the brake: However, if you suddenly shift from D to a lower gear at high speed, the engine RPM will be very high, and the car will jerk significantly. But when driving at low speeds, you can shift to a lower gear directly. Some cars also have S or M modes, which can be switched to from D mode while driving. 2. Shifting from N to R or D requires pressing the brake and holding the lock button; otherwise, the gear cannot be engaged. However, shifting from R or D to N can be done directly without pressing any buttons.

1

3

Share

What is the Chinese equivalent of Euro 4 emission standards?

Euro 4 emission standards are equivalent to China's National IV standards. Below are specific details about Euro 4: 1. In terms of emission standards, Euro 4 is similar to China's National IV, but Euro 4 is more stringent than National IV. 2. The Euro 4 standard refers to the Euro 4 emission standard, which was implemented at the end of 2005 as an important automotive exhaust emission standard currently adopted by most countries. 3. China's National IV emission standard represents the fourth phase of national standards for motor vehicle pollutant emissions. The main automotive emission pollutants include HC (hydrocarbons), NOx (nitrogen oxides), CO (carbon monoxide), and PM (particulate matter).

1

4

Share

What should be noted after replacing brake pads?

After replacing brake pads, the following points should be noted: 1. Try to avoid heavy braking and sudden stops, as the friction surface of the new brake pads has not fully conformed to the surface of the brake disc. 2. After installing new brake pads, it is essential to break them in properly to ensure quick and effective conformity between the brake pads and the brake disc, guaranteeing optimal braking performance. 3. Minor noises during braking after replacing new brake pads are normal. If these noises disappear after the break-in period, there is no need for concern. However, if the noise is significant and persists for an extended period, it is advisable to visit a quick repair shop to check whether the noise is caused by edge wear.

16

4

Share

What is the difference between AT tires and MT tires?

AT tires refer to all-terrain tires, while MT tires refer to mud tires. The main differences between AT tires and MT tires are as follows: 1. Suitable environments: MT tires are a more extreme type of off-road tire, heavily focused on muddy terrain and not suitable for dry northern regions. AT tires, on the other hand, balance both off-road and on-road performance. 2. Traction capability: MT tires are more suitable for off-road vehicles, offering strong traction and off-road capabilities. AT tires, known as all-terrain tires, are versatile and can be used in many different environments, making them a common choice in the market. 3. Design philosophy: AT tires feature bold and rugged tread patterns with large gaps, while MT tires do not have this design. 4. Comfort level: AT tires are built upon the performance limitations of MT tires, with their rugged tread patterns and gaps leading to increased tire noise and reduced driving comfort.

10

1

Share

Brief Description of the Steps for Removing and Dismantling Car Wheels?

How to Start a Manual Transmission Car with a Dead Battery?

How to reset the tire pressure light on a Toyota Levin?

Do You Need to Press the Brake Every Time You Shift Gears in an Automatic Transmission?

What is the Chinese equivalent of Euro 4 emission standards?

What should be noted after replacing brake pads?

What is the difference between AT tires and MT tires?

What to Do When the Battery Doesn't Hold Charge in Winter?

How to Turn on the Fog Lights on Ora Black Cat?

How to Lift the Wiper Blades on a Kodiaq?

What to Do When Motorcycle Disc Brakes Make Friction Noise?