Automotive Parts and Accessories Manufacturing?

Where to Place the Car Shock Absorber Shim?

It should be placed at the closest point to the body panel when the car door is closed. Below is a related introduction to the door shock absorber shim: Function: It prevents the shock absorber from coming into contact with the car body. When the car turns, the center of gravity shifts to one side, causing the body to tilt and compress the spring. The shim then provides support, helping to reduce the car's body roll. Material: The shim is made of paper, rubber, or copper and is placed between two surfaces to enhance sealing. It serves as a sealing element between static sealing surfaces to prevent fluid leakage. It is installed on the car body by adhesion, and the adhesive material is usually very mild, so it will not damage the surface of the car body.

15

2

Share

Is Paint Peeling and Rusting on a Car Serious?

Paint peeling and rusting on a car can have serious consequences. Here is relevant information about car paint peeling and rusting: 1. Rust Risk: Even after repainting, there may still be a risk of rust due to workmanship and environmental factors. However, some "older cars" can remain in good condition if the region and the owner's maintenance are adequate. If a car is frequently exposed to extreme conditions like high temperature and humidity, rust and other issues may be unavoidable, but this still depends on how well the car is cared for. Vehicles are designed to last a long time, generally around ten years without major issues. Even some new cars may have paint damage due to transportation issues when they arrive at 4S stores, but these stores will repaint and repair them, which does not affect the vehicle's quality. 2. Performance Damage: A 1% rust on the car body reduces its strength by 5%-10%, meaning the car's defensive performance in traffic accidents will be compromised.

2

1

Share

What does the F1 display on the Suzuki GW250 indicate?

FI is the indicator light for fuel-injected motorcycles. When the key is first turned on, the fuel injection system performs a self-check, and the FI indicator light will illuminate and then turn off. If this indicator light does not turn off or starts flashing, the flashing frequency represents a specific fault code. By reading the fault code through after-sales service, the issue can be identified. Below is an introduction to the Suzuki GSX250: Configuration: The Haojue Suzuki GSX250 is equipped with a parallel twin-cylinder water-cooled engine with a displacement of 248CC, two valves per cylinder, a maximum power of 18.4KW at 8000 RPM, a maximum torque of 23.4NM, and a fuel tank capacity of 15L, meeting emission standards. Appearance: The overall design continues the heritage of a supercar, with smooth and flowing lines. The full and rounded curves of the vehicle outline a uniquely charming and stylish appearance.

14

3

Share

What Causes Intermittent Car Starting Failure?

Car intermittent starting failure reasons are as follows: Battery failure: The car engine makes a "click-click-click" sound, starts immediately upon ignition, but still fails to start after hearing the "click-click-click" sound, and the battery indicator light on the car dashboard is also on. This indicates a depleted battery. Spark plug blockage: The vehicle starts successfully, but there is obvious hesitation during startup. You should observe the engine's operation. If there is continuous shaking or intermittent shaking, it is likely caused by the spark plug. At this point, you can start with the spark plug to see if there are any hidden dangers, so as to replace it in time. Fuel pump pressure loss: After prolonged use, the fuel pump will inevitably experience internal wear, leading to insufficient fuel supply pressure and difficulty in ignition. In this case, replacing the fuel pump can solve the problem.

6

0

Share

Does the Suzuki GSX250R have storage space?

Suzuki GSX250R does not have storage space, and you can only install it yourself. The following is an introduction about Suzuki: Brand introduction: Suzuki (SUZUKI) was established in 1920 and is a Japanese automobile manufacturing company. The "S" in the Suzuki trademark pattern is the first capital letter of "SUZUKI", which gives people a sense of infinite power and symbolizes the unlimited development of Suzuki Motor Corporation. In terms of power: The Suzuki GSX250R is a 250CC twin-cylinder four-stroke water-cooled motorcycle with a maximum horsepower of 25 and a maximum power of 18.4KW. When driving on normal urban roads, the fuel consumption per 100 kilometers of this car is about 4.5-5.0L, and the transmission method is chain drive.

17

3

Share

Should You Charge the Low or High Pressure Side First When Adding Refrigerant to a Car AC?

When adding refrigerant to a car AC, start with the low-pressure side because the system is vacuumed, and the high-pressure side retains an interface only suitable for adding refrigerant. This approach is chosen based on the different substances being added. Precautions for Adding Refrigerant to a Car AC: Before adding refrigerant, use a pressure/vacuum machine to pressurize the system and check for leaks. If leaks are found, inspect all AC system components, including pipe joints, condensers, evaporators, dryer bottles, compressors, etc., by spraying soapy water to locate the leaks. Address or replace the faulty parts. After replacement, pressurize the system again to check for leaks. Only proceed with vacuuming and adding refrigerant once no leaks are confirmed. Steps for Adding Refrigerant: Connect the refrigerant gauge to the AC system (both high and low-pressure pipes) and vacuum the system. Select the low-pressure side for vacuuming (turn the switch corresponding to the low-pressure gauge counterclockwise, ensuring the high-pressure gauge switch remains closed). Generally, there's no need to monitor the negative pressure value; 3 minutes of vacuuming is sufficient. After the time elapses, tighten the low-pressure gauge switch, then connect the refrigerant canister for filling (keeping the high-pressure switch closed and only opening the low-pressure switch). If too much refrigerant is added, release the excess through the refrigerant gauge. Excess refrigerant can reduce cooling efficiency, increase the compressor's workload, and shorten its normal lifespan.

3

0

Share

Automotive Parts and Accessories Manufacturing?

Where to Place the Car Shock Absorber Shim?

Is Paint Peeling and Rusting on a Car Serious?

What does the F1 display on the Suzuki GW250 indicate?

What Causes Intermittent Car Starting Failure?

Does the Suzuki GSX250R have storage space?

Should You Charge the Low or High Pressure Side First When Adding Refrigerant to a Car AC?

What is the top speed of the Suzuki GSX250?

How Often Should Mazda Transmission Fluid Be Changed?

Why was the Wuling Zhiguang V discontinued?

Can You Hold Both a Car Driver's License and a Motorcycle License Simultaneously?