At what mileage does the first-generation Jog typically start burning oil?

1 Answers
MacCamille
07/30/25 8:42am
Jog first-generation may start burning oil after approximately 35,000 kilometers. The reasons for oil burning include: long-term normal wear causing increased clearance between the cylinder and piston rings, severely reduced sealing performance which allows crankcase oil to enter the combustion chamber and mix with gasoline for combustion, resulting in oil burning phenomenon. Mild cases may show no blue smoke or minimal smoke emission, while severe cases exhibit significant smoke. Some vehicles may also experience damaged valve stem seals. If the engine has experienced oil shortage, it may accelerate wear leading to cylinder sticking or piston ring seizure. These conditions require replacement of new components for resolution. Other contributing factors include using low-quality oil or oil with incorrect viscosity grade, as well as overfilling the engine oil.
Was this review help?
20
0
Share
More Forum Discussions

What are the solutions for high water temperature in Yuchai engines?

Here are the causes and solutions for high water temperature in Yuchai engines: 1. Radiator issues: (1) If the radiator is too far from the engine, causing the fan to operate outside the wind circle, adjust the radiator's installation position; (2) If the air conditioning condenser blocks the radiator, there are two solutions: first, if there's sufficient space in the engine compartment, relocate the condenser; second, if the generator has sufficient output, install an electric fan in front of the condenser. 2. Maintenance and usage issues: Using gasoline below the required octane rating (which is not allowed in principle) or advanced ignition timing can cause engine knocking, leading to high water temperature. The solution is to adjust the distributor to slightly retard the ignition timing.
6
0
Share

What type of suspension does the Mercedes-Benz S600 use?

The Mercedes-Benz S600 uses a double-wishbone independent suspension at the front and a double-wishbone independent suspension at the rear. The suspension refers to a connection structure system between the body, frame, and wheels, which includes components such as shock absorbers, suspension springs, anti-roll bars, subframes, lower control arms, longitudinal links, steering knuckle arms, rubber bushings, and connecting rods. More details about the double-wishbone independent suspension are as follows: 1. The double-wishbone independent suspension, also known as a double-A-arm independent suspension, uses upper and lower unequal-length wishbones (shorter upper and longer lower) to allow the wheels to automatically change the camber angle during vertical movement, reducing changes in track width and tire wear. It also adapts to road conditions, providing a large tire contact area and excellent road grip. 2. The double-wishbone suspension offers outstanding performance and is used in supercars like Ferrari and Maserati. It has advantages such as high lateral stiffness, excellent anti-roll performance, and strong grip, but it occupies more space, has higher costs, and requires complex suspension alignment parameter settings. 3. The double-wishbone suspension consists of upper and lower unequal-length V-shaped or A-shaped control arms and a strut-type hydraulic shock absorber, with the upper control arm typically shorter than the lower one. One end of the upper control arm connects to the strut shock absorber, while the other end connects to the body. One end of the lower control arm connects to the wheel, while the other end connects to the body. 4. The upper and lower control arms are also connected by a link rod, which is also connected to the wheel. In the overall suspension structure, the connection of multiple pivot points enhances the integrity of the upper and lower control arms and the entire suspension.
2
2
Share

How to Report Modified Daytime Running Lights to the Vehicle Management Office?

To report modified daytime running lights to the vehicle management office, follow these steps: Visit the office and explain the modification to the relevant staff to complete the necessary procedures. This includes annotating the changes in the motor vehicle registration certificate, retrieving the old driving license, and issuing a new one. Daytime running lights (DRLs) are daytime visibility lights installed on both front sides of the vehicle to enhance its presence during daylight. Notes on proper headlight usage: 1. Use low beams when driving at night. 2. Avoid using high beams when driving closely behind another vehicle in the same direction. 3. Alternate between high and low beams when navigating sharp turns, slopes, arched bridges, crosswalks, or uncontrolled intersections at night.
11
0
Share

What are the precautions for replacing the high-pressure fuel pump in a Highlander?

Precautions for replacing the high-pressure fuel pump in a Highlander include disconnecting the fuel pump power supply and taking fire prevention measures. Below is more relevant information: 1. Brief introduction to the function of the high-pressure fuel pump: (1) It can increase fuel pressure to ensure complete combustion of the fuel. (2) It enables high-pressure injection for better atomization. (3) It can serve as a power source for hydraulic devices such as jacks, heading machines, extruders, and cotton gins. 2. Reasons for damage to the high-pressure fuel pump in a car: (1) Improper behavior during refueling. (2) Avoid waiting until the fuel warning light comes on before refueling, as this can shorten the fuel pump's lifespan. (3) Too little fuel or running out of fuel can burn out or damage the fuel pump. (4) Overfilling the fuel tank.
14
5
Share

What is the maintenance interval for the Highlander?

The maintenance interval for the Highlander is every 10,000 kilometers or 6 months. Below is more relevant information: 1. Highlander parts replacement cycle: Engine oil and oil filter should be replaced every 10,000 kilometers or 6 months, the air conditioning filter every 20,000 kilometers or 1 year, the air filter, brake fluid, as well as the transfer case oil and rear differential oil for four-wheel-drive models every 40,000 kilometers or 2 years, and the spark plugs every 60,000 kilometers. 2. Highlander introduction: The Highlander is a vehicle produced by Toyota, a large-sized SUV in the Toyota family. It features a spacious body and an innovative, roomy interior. Moreover, the Highlander comes standard with the highest level of safety equipment in its class. This SUV is exceptionally quiet while driving and offers outstanding responsiveness, combining versatility with driving comfort.
2
2
Share

What Causes the Clicking Sound When Braking in a Cayenne?

Here are the reasons why a Cayenne may produce a clicking sound when braking: 1. Excessive wear on brake discs and brake pads: Both brake discs and brake pads are high-wear components that experience friction with each brake application. Over time, wear naturally occurs, and when excessive, it can lead to abnormal noises. 2. Improper installation of brake pads: If the brake pads are installed incorrectly or are of the wrong model, abnormal noises may also occur. Reinstalling the brake pads may resolve the issue. 3. Other possible causes: Generally, faults in components such as the caliper, brake disc, or brake pads can produce this noise. If the noise persists, check for dragging brakes, as poor caliper reset can cause prolonged friction between the disc and pad, leading to abnormal noises under certain conditions. Additionally, foreign objects on the brake pads or discs can also cause abnormal noises.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.