···
Log in / Register

At what location are solid line violations photographed?

4 Answers
CarmenDella
09/02/25 5:06am

Solid line lane changes within approximately 100 meters of an intersection are likely to be captured by traffic violation cameras. Normally, cameras that monitor solid line violations and traffic flow face backward for capturing violations. Here are specific details about solid line violation photography: Introduction to solid line violation cameras: Cameras that photograph solid line violations are road surveillance cameras primarily used to capture violations such as wrong-way driving, solid line lane changes, and illegal parking. These are typically the "7-shaped white traffic poles" installed roadside. Therefore, when encountering a pole with multiple cameras, do not take chances. Precautions regarding vehicle line crossing: When the left wiper's protruding node aligns with an object on the ground in your line of sight, the left wheel will run over that object during movement. Maintaining 60 cm from the centerline while driving is generally safe. When the intersection point between the cotton board and A-pillar aligns with the centerline in your vision, the vehicle body is precisely 60 cm from the centerline. To determine right wheel position: when your sightline intersects the right wiper with a target object, the tire will run over that object.

Was this review help?
11
0
Share
AlexandraFitz
09/14/25 7:16am

I often notice that the locations where running over solid lines are captured are mainly at spots with electronic surveillance. The most common places are under traffic lights at intersections, where cameras mounted on high monitoring poles capture the moment vehicles cross the line. Main roads in the city, such as arterial roads and areas around commercial districts, are also prone to enforcement, especially when crossing solid lines in turning lanes. On highways, cameras are installed at solid line zones before entrance ramps and exits, and crossing them results in a violation. Areas near tunnels and overpasses may also have surveillance due to high traffic volume and safety risks in these sections. Developing the habit of not crossing solid lines while driving is crucial, as it not only avoids fines and penalty points but also ensures safe travel. If you're unsure where cameras are located, you can pay attention to road sign warnings or navigation alerts, but the safest approach is to follow traffic rules and avoid taking shortcuts for convenience.

Was this review help?
20
0
Share
Expand All
VonHeidi
10/28/25 7:57am

After years of driving, most cases of crossing solid lines being captured occur at locations with strict traffic control. Intersections are the most obvious spots – stopping over the line at red lights will trigger cameras, usually mounted on signal poles or cantilevers. Urban expressway ring road exits also frequently have monitoring, where crossing solid lines immediately activates enforcement. Rural roads may have fewer, but urban bridge and tunnel entrances are hotspot areas. Crossing solid line violations can easily cause accidents, so drivers should always pay attention to lane markings – treat solid lines like walls that must not be crossed. Develop the habit of checking mirrors before driving, change lanes in advance, and avoid forcing your way in solid line zones for both safety and convenience. Be extra cautious in bad weather, as slippery roads significantly increase the risk of skidding when crossing lines. Ultimately, these measures exist to maintain order and reduce congestion – compliance brings peace of mind.

Was this review help?
4
4
Share
Expand All
JosephineLynn
12/11/25 8:13am

Locations where crossing solid lines are captured are typically key points equipped with electronic cameras. The primary spots are under traffic lights at intersections, where cameras are mounted high on monitoring poles for automatic capture. Highways also have setups at exit ramps to promptly record line-crossing behaviors. These points are usually selected in areas prone to congestion or accidents, such as central city intersections or near large roundabouts. Nearby landmarks like crosswalks or intersection signs often have cameras focused on vehicle violations. Drivers should maintain center-lane driving to avoid fines or even penalty points for line-crossing violations.

Was this review help?
14
0
Share
Expand All
More Forum Discussions

Where are Haval engines produced?

Haval vehicles' engines are produced at two manufacturing bases: Haval Xushui Factory and Haval Tianjin Factory. Below is more information about Haval: 1. Haval vehicles use the GW4G15 series engines independently developed by Great Wall: The GW4G15 series engines reflect Great Wall Motors' efficient independent R&D capabilities. The Haval H6 is equipped with the newly developed GW4HG15 1.5T engine by Great Wall, which features an aluminum alloy cylinder block, dual overhead camshafts, intake-side VVT technology, and exhaust turbocharging technology. It delivers a maximum power output of 110kW at 5600 rpm and a peak torque of 210Nm between 1800-4200 rpm. 2. The 1.5T engine used in Haval vehicles is regarded by many owners as the most powerful 1.5T engine in China: The engine integrates advanced technologies such as centrally mounted fuel injectors, cylinder head-integrated exhaust manifold, high transient response electronically controlled turbocharger, two-stage variable displacement oil pump, dual VVT (intake and exhaust), and a dual-circuit cooling system.
19
5
Share

How to Use Hazard Lights?

Correct methods for using hazard lights are as follows: 1. When driving on highways with low visibility, such as in fog, rain, snow, sand, or hail, hazard lights can be turned on; 2. When towing a malfunctioning vehicle, both the towing vehicle and the towed vehicle should turn on hazard lights; 3. When a vehicle breaks down or a traffic accident occurs on the road, hazard lights warn surrounding vehicles to detour; 4. When temporarily parking on the road, hazard lights need to be turned on as a signal indicating the vehicle is preparing to slow down or stop in an emergency. More information about vehicle hazard lights is as follows: 1. Vehicle hazard lights, commonly known as double flashing lights, are when both turn signals flash together. There is a red triangular button on the vehicle's dashboard, pressing it will turn on the hazard lights. 2. For some microcars, the hazard light switch is located on the front part of the steering column near the steering wheel, where there is a small red lever. Lifting this lever will turn on the hazard lights.
4
3
Share

How to Repair Small Dents on Car Metal Panels?

If it's the front or rear bumper, which is usually made of plastic, the restoration is relatively easier. Pour hot water over the dented area of the bumper to heat it up. Once it reaches a certain temperature, it will soften. At this point, you need to strike while the iron is hot by pushing from inside the engine compartment outward until the dent is restored. If the dent is on the body's waistline or is a sharp crease, you will need to go to a 4S shop or auto repair shop for metal sheet repair. Here is an introduction to dent repair techniques: 1. Auto repair shops have a technique called dent repair, also known as light metal sheet repair. However, dent repair techniques are quite similar to DIY tool repairs. Both methods involve using suction cups to pull out the dented area, then inserting a hook behind the dent to slowly push it out, and finally using a rubber hammer to smooth out the protruding parts. 2. Door dent repair can save money and time, but not all dents can be repaired. As long as the paint surface is not peeling or chipped, and the dent is not too deep, the repair is relatively straightforward.
14
3
Share

How to Deal with Overly Stiff Shock Absorbers?

Methods to address overly stiff shock absorbers can be divided into the following three scenarios: 1. Break-in period for new cars: Generally, excessive stiffness in shock absorbers is due to the vehicle being new, and its components not having fully broken in yet. During this time, the sensation of overly stiff shock absorbers is normal, and it should improve after the break-in period. 2. Reduce tire pressure: The stiffness of the shock absorbers can be adjusted by altering the tire pressure. However, the reduced tire pressure should remain within the normal range. This method can provide slight relief. 3. Upgrade to adjustable shock absorbers: Consult with professionals and, if modifications are permitted, replace the current shock absorbers with adjustable ones that allow for hardness adjustment, such as coilover shock absorbers, which can also adjust height and damping.
19
1
Share

How to Replace BMW Wiper Blades?

Here are the steps to replace BMW wiper blades: 1. For F-series models such as F01, F18, F35, etc.: a) Ensure the vehicle is turned off. b) Press the start button to power on the vehicle without stepping on the brake or starting the engine. c) Wait for 5 seconds, then turn off the power. d) With the engine off, push the wiper lever upward and hold for more than 3 seconds. e) Rotate the wiper blade 90° to remove it, and reposition the wiper after replacement. 2. For G-series models such as G01, G30, G32, etc.: a) Stay outside the vehicle and lock it using the remote control. b) Wait for 5 seconds, then unlock the vehicle and enter. c) Push the wiper lever upward, and the wiper will swipe three times and stop in the middle of the windshield. d) Replace the new wiper blade. e) After replacement, press the 'START/STOP' button three times consecutively. f) Push the wiper lever downward once to exit the maintenance mode.
11
4
Share

How to Open the Hood of an A6?

The method to open the hood of an A6: There is a pull handle on the left front side of the driver's seat. Pull it, and the hood will pop up slightly. Then, press the center of the hood with your hand to open it completely. Functions of the engine hood: 1. Airflow guidance: The shape of the engine hood effectively adjusts the direction of airflow relative to the car's movement and reduces the resistance caused by airflow, minimizing its impact on the vehicle. By guiding the airflow, air resistance can be converted into beneficial forces, increasing the tire's grip on the road and enhancing driving stability. 2. Protection for the engine and surrounding components: By improving the strength and structure of the engine hood, it effectively prevents adverse effects such as impacts, corrosion, rain, and electrical interference, ensuring the vehicle operates normally. 3. Aesthetics: The exterior design of a vehicle is a direct reflection of its value. As a crucial part of the overall appearance, the engine hood plays a vital role in enhancing visual appeal and embodying the concept of the car. 4. Assisting driver visibility: During driving, the driver's ability to correctly judge road conditions and the situation ahead relies heavily on the reflection of natural light and the view ahead. The shape of the engine hood effectively adjusts the direction and form of reflected light, thereby reducing its impact on the driver.
9
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.