At what level of wear should a wire rope be scrapped?

1 Answers
VanNolan
07/30/25 1:00am
Wire rope wear: For lifting machinery wire ropes, the rope should be scrapped if the number of broken wires within one lay length reaches 10% of the total number of wires. Automobile abnormal noises: As the usage time of automobiles increases, along with improper operation, maintenance quality, and the influence of the natural environment, various components may produce noises exceeding specified limits due to wear, damage, looseness, aging, poor contact, short circuits, and open circuits. These noises include knocking sounds, high-speed operation whistles, part rubbing sounds, gear grinding sounds, etc. Approximately 70% of automobile faults are manifested through abnormal noises. Therefore, identifying general patterns and characteristics of faults from these most intuitive manifestations can greatly facilitate automobile fault diagnosis. Automobile performance abnormalities: Automobile performance abnormalities are relatively common fault phenomena. Examples include difficulty starting, automatic stalling, generator failure to generate electricity, difficulty shifting gears, steering failure, brake failure, etc.
Was this review help?
13
1
Share
More Forum Discussions

What Causes Unstable Idling Speed in a Van?

The reason for unstable idling speed in a van is excessive carbon buildup in the throttle body. When this occurs, the throttle body can be removed and cleaned. After cleaning and reinstalling the throttle body, it is essential to perform a computer re-calibration; otherwise, it may lead to increased fuel consumption. The throttle body acts as the engine's throat, controlling the amount of air entering the engine. It is installed on the engine's intake pipe. When the driver presses the accelerator pedal, the throttle opening increases, allowing more air to enter the engine cylinders. After the sensor detects the increased air intake, it sends a signal to the ECU (Engine Control Unit), which then commands the fuel supply system to increase fuel injection. As a result, the engine speed rises.
8
0
Share

Is It Normal for the Brakes to Make Noise When Starting the Car?

It is normal for the brakes to make noise when starting the car. When the driver slowly releases the brake pedal, the engine already has enough power to drive the car forward, but the brakes are not fully released. As a result, the moving wheels are held back by the brake system, naturally producing noise. In a manual transmission car, when the brake is released, the transmission does not output power, and the vehicle starts only after the brake is fully released. However, in an automatic transmission car, as soon as the gear is engaged, the transmission already provides force for the tires to rotate forward, but the vehicle does not move because the brake is pressed. When starting an automatic transmission car, the brake is usually released slowly. If the brake is released quickly, this noise will not occur.
17
2
Share

What are the reasons for inaccurate car fuel gauge readings?

The reasons for inaccurate car fuel gauge readings: 1. The fuel gauge pointer fluctuates irregularly: This cannot necessarily be considered a malfunction, as it is related to the design of the fuel pump used to reflect the fuel level; 2. The fuel gauge scale rises: This occurs because the linkage between the fuel level sensor and the float gets stuck, preventing the float from moving up and down normally, causing the fuel level sensor to remain unchanged, thus the fuel gauge pointer stays fixed at a certain position; 3. The fuel gauge suddenly drops to zero: When this happens, it indicates an issue with the vehicle's fuel level sensor, most likely due to contamination of the sensor that hasn't been cleaned in time. Gasoline contains many impurities, and the fuel level sensor being constantly immersed in them can become polluted over time, directly affecting the accuracy of the readings.
1
1
Share

How Wide is a 4.2-Meter Wide-Body Vehicle?

4.2-meter trucks typically have a length of 4200mm, a width ranging from 1600-1800mm, and a height between 1600-1800mm. Here is some additional information: 1. Wide-body light trucks: These usually have a wheelbase between 3300-5200mm, with specifications and load capacity larger than standard light trucks. For the light truck industry, wide-body light trucks are not a new concept. 2. Examples of wide-body light trucks: With the development of the domestic economy and the construction of the highway network, wide-body light trucks, primarily used for medium to long-distance freight transport, have become increasingly popular. Existing wide-body light trucks in the market include Dongfeng Jinba, Dongfeng Duolika, JMC Kairui, Qingling 700P, JAC Weiling, and Foton Aumark.
11
3
Share

What are the causes of starter failure?

The causes of starter failure include the following points: 1. Insufficient battery power. 2. Loose, corroded, or worn battery cables. 3. Faulty starter relay. For automatic transmissions, the gear position switch may also be faulty. 4. Blown fuse. 5. Starter motor failure, including issues with the electric motor and magnetic switch, as well as other component failures. Here are some practical diagnostic steps: For regular vehicles, you can use a wire to short-circuit the two terminals on the starter's electromagnetic switch to start the engine. If the starter operates, the issue is likely with the starter relay or fuse. If the starter does not operate, it can be determined that the starter itself is faulty, with the most common issue being the electromagnetic switch.
1
3
Share

What is the difference between factory paint and 4S shop paint?

There are differences between factory paint and 4S shop touch-up paint, which are as follows: 1. Different spraying environments: The OEM paint shop in the factory is a sealed positive-pressure workshop with air filtered through multiple layers and oil-water separation; 4S shop touch-up paint is done in a separate paint room or outdoors. 2. Different construction tools: Factory paint is applied using robotic automatic spraying in the OEM factory; 4S shop touch-up paint is done manually using ordinary spray guns. 3. Different baking methods: Factory paint in the OEM paint shop uses thermal radiation to bake the car body at temperatures reaching 200 degrees Celsius; 4S shop touch-up paint uses lamp baking.
1
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.