At How Many Kilometers is a Car Scrapped?

How to Replace the Fuel Filter on a Bora?

The steps to replace the fuel filter on a Bora are as follows: 1. Prepare two flat-head screwdrivers and an oil can. First, use one screwdriver to press against the fuel pipe clamp. 2. Insert the other screwdriver between the fuel filter and the clamp, twist it slightly to loosen one end, then remove the fuel filter by pressing the other clamp with your thumb and index finger and pulling the filter out. 3. When installing the new fuel filter, be sure to apply some engine oil to the inside of the clamp and the filter connector, then rotate the filter while inserting it—it should go in easily. 4. It is crucial to apply oil, as the Bora's fuel filter is prone to leaks. It's best not to attempt this yourself, as dealing with a fuel leak can be troublesome. 5. Ideally, use up the fuel in the tank before replacement, or at least wait until the low fuel light comes on to minimize fuel vaporization.

17

1

Share

Why does the newly replaced brake pad smell burnt and get hot?

Newly replaced brake pads smelling burnt and getting hot are caused by the gap between the brake pads and the brake disc being too small or the brake caliper seizing up. Service Life: Under normal driving conditions, the lifespan of front brake pads is generally 30,000–50,000 kilometers, while rear brake pads last 120,000–150,000 kilometers. The replacement time should be determined based on actual wear conditions. The manufacturer's recommended mileage may vary depending on the vehicle model. Replacement: When replacing brake pads, choose products from reputable manufacturers. Genuine manufacturer-produced brake pads typically have clear packaging printing, including a license number, specified friction coefficient, and compliance standards. The packaging box should also contain a certificate of conformity, production batch number, and production date. It is recommended to have new brake pads installed by professionals at certified repair shops to avoid errors that could lead to potential safety hazards. Inspection: When inspecting brake pads, the wear on the brake disc or brake drum should also be checked to ensure sufficient contact area with the brake pads for improved braking performance.

15

1

Share

What Causes Severe Body Shaking When Slowly Releasing the Clutch in First Gear?

The reasons for severe body shaking when slowly releasing the clutch in first gear may include an uneven clutch pressure plate, weakened damping spring tension, or poor contact of the clutch lining. Below are detailed explanations of the causes and solutions: Uneven Clutch Pressure Plate: First gear has a lower gear ratio, and the engine's speed is directly transmitted to the transmission to drive the wheels. When the clutch pressure plate is uneven, the clutch disc may not engage smoothly, causing bouncing and resulting in shaking during startup. The clutch pressure plate should be replaced promptly. Weakened Damping Spring Tension: If the tension of the clutch torsional damping spring weakens, it can cause shaking when the clutch engages. If the issue is confirmed to be with the torsional damping spring, the spring should be replaced immediately. Poor Contact of Clutch Lining: Hardening of the clutch lining surface or adhesion of sticky substances can easily lead to clutch shaking. Any excess material on the clutch lining should be promptly addressed.

15

4

Share

What Are the Advantages of Rear-Wheel Drive Cars?

The advantages of rear-wheel drive cars are as follows: 1. Better acceleration performance and higher comfort. When the vehicle starts, accelerates, or climbs a slope, the center of gravity shifts backward, increasing the traction of the rear wheels as the driving wheels. This enhances the vehicle's starting, acceleration, or climbing ability, providing better driving stability and comfort. It also offers good load-bearing capacity and a simple structure. 2. Superior handling. With the rear wheels responsible for driving, the front wheels can focus on steering, making the vehicle more responsive during turns. Additionally, moving some components from the front to the rear of the vehicle helps achieve a near-perfect 50:50 weight distribution, significantly improving balance and stability. This is why most sports cars use rear-wheel drive. 3. Easier maintenance. The front-engine, rear-wheel-drive layout places components like the engine, clutch, and transmission closer to the cabin, simplifying the layout of control mechanisms and the structure of the steering system, making vehicle maintenance and repairs more convenient.

16

2

Share

Where to Wash the Car Chassis?

Car chassis cleaning should be done at a car wash shop. The steps for cleaning a car chassis are as follows: 1. Lift the car with a lift, wrap the exhaust pipe, wire connectors, etc., and rinse the chassis with a high-pressure water gun. 2. Use a specialized cleaning agent to rinse the chassis again, then dry the chassis with a high-pressure air gun. 3. Finally, unwrap the wrapped parts and lower the car. The introduction to the car chassis is as follows: 1. The car chassis consists of four parts: the transmission system, the running system, the steering system, and the braking system. 2. The function of the chassis is to support and install the car engine and its various components and assemblies, form the overall shape of the car, receive the power of the engine, make the car move, and ensure normal driving.

16

4

Share

Why won't the car start and the engine fault light is on?

If the car won't start and the engine fault light is on, it may be caused by an oxygen sensor failure or a mass air flow sensor failure. Oxygen sensor failure: Modern vehicles are equipped with two oxygen sensors, one before and one after the three-way catalytic converter. The front oxygen sensor detects the air-fuel ratio under different engine operating conditions, while the ECU adjusts the fuel injection quantity and calculates the ignition timing based on this signal. The rear oxygen sensor mainly monitors the performance of the three-way catalytic converter. Therefore, if the oxygen sensor is damaged or the sensor connector is damaged or loose, it can cause the air-fuel mixture to become too lean or too rich, triggering the fault light. Mass air flow sensor failure: The mass air flow sensor, also known as the air flow meter, measures the amount of air intake and converts it into an electrical signal sent to the ECU. Based on the optimal air-fuel ratio, the ECU determines the amount of fuel to inject. If the mass air flow sensor or its circuit malfunctions, the ECU will not receive the correct air intake signal, leading to improper fuel control and causing the air-fuel mixture to become too lean or too rich, which prevents the engine from operating normally.

10

2

Share

At How Many Kilometers is a Car Scrapped?

How to Replace the Fuel Filter on a Bora?

Why does the newly replaced brake pad smell burnt and get hot?

What Causes Severe Body Shaking When Slowly Releasing the Clutch in First Gear?

What Are the Advantages of Rear-Wheel Drive Cars?

Where to Wash the Car Chassis?

Why won't the car start and the engine fault light is on?

Is it normal to fail the Subject 3 test 4 times?

What Causes Loose Steering and Abnormal Noises on Rough Roads?

What is the tire pressure for SUVs?

What Are the Symptoms of Oil and Coolant Mixing?